Go Back  Bike Forums > Search Forums
Reload this Page >

Search Results

Notices
Search: Posts Made By: Crankycrank
Showing results 1 to 10 of 10
Search took 0.01 seconds.
08-21-19, 09:49 AM
Replies: 20
Views: 864
Posted By Crankycrank

What brand and model hub? Photos would also help....

What brand and model hub? Photos would also help. Have you checked any bike shops yet?
08-15-19, 10:17 AM
Replies: 14
Views: 1,037
Posted By Crankycrank

Just give the chain a good wipe with a rag after...

Just give the chain a good wipe with a rag after a few miles of riding after lubing. This usually gets rid of the excess lube that flings off onto your spokes.
08-13-19, 02:51 PM
Replies: 14
Views: 1,037
Posted By Crankycrank

I'd be concerned that doing it this way only...

I'd be concerned that doing it this way only leaves a light film on the outside of the chain and not where you want the lube which is inside all the moving surfaces.
07-18-19, 11:03 AM
Replies: 9
Views: 664
Posted By Crankycrank

I don't know the answer to your question but one...

I don't know the answer to your question but one thing that may help is to look for a manufacturer name labeled or stamped somewhere on the trainer and do a search with that info. Performance and...
07-02-19, 02:41 PM
Replies: 41
Views: 2,264
Posted By Crankycrank

Easiest way to sand a seam is fold the tube so...

Easiest way to sand a seam is fold the tube so that the seam is on the fold. Makes the seam stand out and simple to sand down to match the surface.
06-28-19, 09:01 AM
Replies: 20
Views: 1,139
Posted By Crankycrank

Another vote for getting the quick link pliers...

Another vote for getting the quick link pliers or if out on the road you can use this trick. https://www.youtube.com/watch?v=85Uednr4zFI Even a rock will do to knock the link loose.
06-09-19, 01:18 PM
Replies: 12
Views: 807
Posted By Crankycrank

I'm with the grease crowd. Anti-Seize is a little...

I'm with the grease crowd. Anti-Seize is a little more long lasting but is a big mess to clean off especially when it gets on your hands if you have to do a mid-ride adjustment. Either will work fine...
06-09-19, 08:21 AM
Replies: 12
Views: 807
Posted By Crankycrank

Screw the bolt all the way into the wedge then...

Screw the bolt all the way into the wedge then loosen the bolt about 1/4". Tap the head of the bolt with a rubber mallet or a steel hammer with a block of wood to protect the bolt. This will push the...
05-23-19, 05:18 PM
Replies: 4
Views: 507
Posted By Crankycrank

That would be the easiest and best solution IMHO.

That would be the easiest and best solution IMHO.
05-01-19, 08:39 AM
Replies: 17
Views: 883
Posted By Crankycrank

Ditto. You can also soak the freehub in Odorless...

Ditto. You can also soak the freehub in Odorless Mineral Spirits after removing the rubber seal. Spin the hub around every few hours to loosen up the gunk. If you have access to an air compressor you...
Showing results 1 to 10 of 10


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

Copyright 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.