Go Back  Bike Forums > Search Forums
Reload this Page >

Search Results

Notices
Search: Posts Made By: mrrabbit
Showing results 1 to 18 of 18
Search took 0.01 seconds.
12-05-20, 12:36 PM
Replies: 18
Views: 731
Posted By mrrabbit

Gap calipers . . . . . . so long as sidewall...

Gap calipers . . .

. . . so long as sidewall thickness is .5 mm or more, there's some life left.

Most rims start at 1.4 to 1.6mm

=8-)
11-23-20, 07:11 PM
Replies: 21
Views: 852
Posted By mrrabbit

You're doing it wrong. The only time you...

You're doing it wrong.

The only time you loosen is to RESET and START OVER.

1. Loosen - tap with a plastic or rubber mallet to ensure the wheel is reset - i.e. has serious slack or play.
2. ...
11-14-20, 10:08 PM
Replies: 52
Views: 1,699
Posted By mrrabbit

Stress Relieving =8-|

Stress Relieving

=8-|
10-07-20, 09:05 PM
Replies: 27
Views: 1,236
Posted By mrrabbit

It will crack where the seattube meets the bottom...

It will crack where the seattube meets the bottom bracket lug.

It's made in Mexico....the cracking issue at the BB applies to 850, 1000, 1500, 2000 and sadly, 3000 modelos after 1981.

While the...
10-06-20, 11:23 AM
Replies: 2
Views: 317
Posted By mrrabbit

1. No super lights or light weights . . . middle...

1. No super lights or light weights . . . middle weights on up. You want inner wall thicknesses of 2.2mm or higher.
2. Washers are NOT hole fillers - they are head / elbow spacers.
3. The...
10-06-20, 11:09 AM
Replies: 14
Views: 757
Posted By mrrabbit

Bent cage . . . been in a side-swipe type...

Bent cage . . . been in a side-swipe type accident . . . and someone tried to bend it back . . . a little too far.

Repairable by the way.

=8-|
07-05-20, 01:08 PM
Replies: 38
Views: 1,421
Posted By mrrabbit

2 Kinds of dish for 99.9999% of the bicycles we...

2 Kinds of dish for 99.9999% of the bicycles we ride:

1. Adjective dish (appearance) caused by dual flanged hubs.
2. Verb dish (action) which is a TECHNICAL requirement for building ALL wheels....
07-05-20, 12:16 PM
Replies: 18
Views: 747
Posted By mrrabbit

You should change your sig: "Your Daily Dose...

You should change your sig:

"Your Daily Dose - Common Sense Rx"

=8-)
07-01-20, 08:38 PM
Replies: 11
Views: 488
Posted By mrrabbit

#1...

#1 (https://www.bikeforums.net/usertag.php?do=list&action=hash&hash=1) cause of broken nipples is spokes that are too short.

Nipples are fasteners, not spoke extenders.

A properly built wheel...
05-31-20, 06:17 PM
Replies: 26
Views: 1,198
Posted By mrrabbit

Do a stress relief cycle...see if any more break....

Do a stress relief cycle...see if any more break.

=8-|
05-30-20, 03:34 PM
Replies: 19
Views: 661
Posted By mrrabbit

People seem to have a hard time understanding...

People seem to have a hard time understanding that the stress relieving process has multiple benefits:

1. Early on, it assists with spoke setting.
2. Near finishing point, reveals if more work...
05-28-20, 10:34 AM
Replies: 27
Views: 936
Posted By mrrabbit

There are three levels for polish for stainless...

There are three levels for polish for stainless steel spokes:

no polish
semi-polished
polished

CN and Wheelsmith by default do polished.

But I've had CN do semi-polish for me in the past.
05-23-20, 08:56 AM
Replies: 9
Views: 369
Posted By mrrabbit

If the hubs are pure french....there's a slight...

If the hubs are pure french....there's a slight possibility they might be 13 balls rear (Maillard Helicomatic), much smaller (3/16 or 5/32) than the ball bearings we see for the typically 10 front...
09-09-19, 11:10 PM
Replies: 46
Views: 7,335
Posted By mrrabbit

What's really important here is that you have an...

What's really important here is that you have an assembly by which to keep the meter calibrated.

As general rule of thumb for modern day alloy rims:

Single wall = 90 to 95 kgf
Double wall = 95...
09-03-19, 09:27 PM
Replies: 6
Views: 1,344
Posted By mrrabbit

There's science and engineering... ...then...

There's science and engineering...

...then there's application.

Spoke calculator should simply provide a calculated length result.

Because a DT Swiss double butted 2.0 / 1.8 / 2.0 will...
09-03-19, 09:11 PM
Replies: 94
Views: 6,601
Posted By mrrabbit

Wow...just wow... 1. Most alloy rims are...

Wow...just wow...


1. Most alloy rims are rated for 90kgf to 110kgf tension AFTER a proper stress relieving cycle has been done.

2. Select makes and models can survive 110kgf to 130kgf.

3....
05-14-19, 02:04 PM
Replies: 6
Views: 461
Posted By mrrabbit

At a minimum...when a wheel is done: 1. Ends...

At a minimum...when a wheel is done:

1. Ends of the spokes must penetrate the thickness of the inner wall of the rim.
2. Come up to about 1.5mm below the screwdriver slot of the nipple.

That's...
02-16-10, 07:44 PM
Replies: 13
Views: 7,046
Posted By mrrabbit

Look at the screwdriver flat portion of the...

Look at the screwdriver flat portion of the nipples:

1. If spoke end has passed it - result = ok
2. If spoke end has reached the flat - result = ok
3. If spoke end has come up to within a...
Showing results 1 to 18 of 18


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2021 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.