Fixed Cleats: best way to find the correct angle
#1
Junior Member
Thread Starter
Join Date: Jan 2016
Posts: 16
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 6 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Fixed Cleats: best way to find the correct angle
For those of you who use fixed cleats, what is the best way to find the right angle of your cleat position. I've decided to start using fixed cleats because I love the locked in feeling they provide, but before riding more miles with them, I want to make sure they're in the right position so I don't get injured.
#2
wears long socks
For those of you who use fixed cleats, what is the best way to find the right angle of your cleat position. I've decided to start using fixed cleats because I love the locked in feeling they provide, but before riding more miles with them, I want to make sure they're in the right position so I don't get injured.
The angle would depend on your natural gait.
#3
Advocatus Diaboli
Join Date: Feb 2015
Location: Wherever I am
Posts: 8,715
Bikes: Merlin Cyrene, Nashbar steel CX
Mentioned: 14 Post(s)
Tagged: 1 Thread(s)
Quoted: 4818 Post(s)
Liked 1,554 Times
in
1,019 Posts
#4
Senior Member
Join Date: Jan 2005
Location: Baltimore, MD
Posts: 5,680
Mentioned: 18 Post(s)
Tagged: 0 Thread(s)
Quoted: 2655 Post(s)
Liked 3,216 Times
in
1,835 Posts
To the OP: among my friends who used nailed-on cleats, we'd ride with a new pair of shoes without cleats until the pedal cage left marks in the soles of the shoes that made it obvious where the cleat slot should go. Something like that approach should be adaptable to clipless pedals.
#5
Full Member
I'm a long time convert to zero-float cleats. To set the cleat position, I sat on the edge of a table and let my legs dangle over the edge, paying close attention to the angle my feet stabilized at and set my cleats to mimic that position when clipped in. It took a couple of rides to fine tune the positioning - not surprisingly each foot ended up at a different angle. While you're in the fine tuning phase, listen to your knees they will complain the loudest from a misalignment. If I ride cleats with float now, I feel that my feet are side-slipping and losing power through the downstroke.
The problem with riding with loose cleats for positioning is that unless you can take your shoe(s) off without unclipping and then mark the cleat position on the sole, you'll lose it from the force of unclipping.
The problem with riding with loose cleats for positioning is that unless you can take your shoe(s) off without unclipping and then mark the cleat position on the sole, you'll lose it from the force of unclipping.
#6
Senior Member
Join Date: Dec 2014
Location: Burbank
Posts: 465
Bikes: Fuji roubaix 1.1
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 20 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
For those of you who use fixed cleats, what is the best way to find the right angle of your cleat position. I've decided to start using fixed cleats because I love the locked in feeling they provide, but before riding more miles with them, I want to make sure they're in the right position so I don't get injured.
#8
Senior Member
For those of you who use fixed cleats, what is the best way to find the right angle of your cleat position. I've decided to start using fixed cleats because I love the locked in feeling they provide, but before riding more miles with them, I want to make sure they're in the right position so I don't get injured.
#9
Senior Member
Join Date: Dec 2009
Location: Houston, TX
Posts: 28,682
Bikes: 1990 Romic Reynolds 531 custom build, Merlin Works CR Ti custom build, super light Workswell 066 custom build
Mentioned: 110 Post(s)
Tagged: 1 Thread(s)
Quoted: 6556 Post(s)
Likes: 0
Liked 58 Times
in
36 Posts
I use 5° float cleats and have absolutely no sense of looseness or side-slip. Low float cleats are a brilliant solution to the issue of getting cleat placement right. And make no mistake: I rode nailed on cleats for many years.
Regarding getting zero float cleats placement right is a problem. Without toeclips to hold the foot in place you can't ride very far without cleats to imprint the bottom of the shoe. Best way I know is to mount the cleats loosely, mount the bike on a trainer stand and pedal for awhile. Then have an assistant tighten the bolts for you without letting the cleats shift.
Regarding getting zero float cleats placement right is a problem. Without toeclips to hold the foot in place you can't ride very far without cleats to imprint the bottom of the shoe. Best way I know is to mount the cleats loosely, mount the bike on a trainer stand and pedal for awhile. Then have an assistant tighten the bolts for you without letting the cleats shift.
Last edited by rpenmanparker; 02-15-17 at 06:08 PM.