Upgrade freehub budy HG to micro spline body
#1
Newbie
Thread Starter
Join Date: Jun 2020
Location: Quito
Posts: 2
Bikes: MTB GER Level 4.5
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Upgrade freehub budy HG to micro spline body
Hi guys
I'm thinking to upgrade my current groupset ( a mix of Tourney/Altus/Acera) to deore m6000 groupset but since the new deore m5100-12 speed groupset was released a few days ago, I'm planning to buy the m6100 instead
Since deore m5100 12 speed cassette uses the micro spline freehub body, I want to know if it is possible to replace my current freehub body (shimano FH-RM35) with micros spline body. Or, I have to buy a new Freehub which accepts micro spline ?
Thanks for your help
I'm thinking to upgrade my current groupset ( a mix of Tourney/Altus/Acera) to deore m6000 groupset but since the new deore m5100-12 speed groupset was released a few days ago, I'm planning to buy the m6100 instead
Since deore m5100 12 speed cassette uses the micro spline freehub body, I want to know if it is possible to replace my current freehub body (shimano FH-RM35) with micros spline body. Or, I have to buy a new Freehub which accepts micro spline ?
Thanks for your help
Last edited by dhub92; 06-23-20 at 05:02 PM.
#3
Very Slow Rider
Join Date: Jul 2017
Location: E Wa
Posts: 1,274
Bikes: Jones Plus LWB, 1983 Centurion Japanese CrMo bike
Mentioned: 12 Post(s)
Tagged: 0 Thread(s)
Quoted: 500 Post(s)
Liked 132 Times
in
101 Posts
I was thinking of doing the same thing because I have the Sunrace 12 speed 11-50t but going to a 10-51t would allow me to switch from a 30t to a 28t chainwheel, resulting in a little higher top gear and my low gear would be pretty damn low (good for climbing because I wouldn't be in my largest cog for as long, if ever).
Mind you, I have reallly big 29x3.0 tires so takes a lot of gear reduction to kick those guys over.
#4
Newbie
Thread Starter
Join Date: Jun 2020
Location: Quito
Posts: 2
Bikes: MTB GER Level 4.5
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
That's a really good point but that will limit the OP to a 11t smallest cog, rather than the new 10-51t put out by Shimano.
I was thinking of doing the same thing because I have the Sunrace 12 speed 11-50t but going to a 10-51t would allow me to switch from a 30t to a 28t chainwheel, resulting in a little higher top gear and my low gear would be pretty damn low (good for climbing because I wouldn't be in my largest cog for as long, if ever).
Mind you, I have reallly big 29x3.0 tires so takes a lot of gear reduction to kick those guys over.
I was thinking of doing the same thing because I have the Sunrace 12 speed 11-50t but going to a 10-51t would allow me to switch from a 30t to a 28t chainwheel, resulting in a little higher top gear and my low gear would be pretty damn low (good for climbing because I wouldn't be in my largest cog for as long, if ever).
Mind you, I have reallly big 29x3.0 tires so takes a lot of gear reduction to kick those guys over.
Back to the original question, is it possible to replace the regular HG freehub body (FH-RM35) with the new micro spline body ? what do you guys think ? or, Should I go for the m6000 2x10 (28-38t) instead ?
Last edited by dhub92; 06-23-20 at 05:20 PM.