Not strictly vintage but...
#1
Fixed on the plains.
Thread Starter
Not strictly vintage but...
I'm trying to figure out how I would go about cleaning up my cranks for my new build without damaging the logo on it. Current suggestion is to tape over it and buff the rest of it.
#2
Senior Member
Join Date: Oct 2015
Location: PDX
Posts: 14,101
Bikes: Merz x 5 + Specialized Merz Allez x 2, Strawberry/Newlands/DiNucci/Ti x3, Gordon, Fuso/Moulton x2, Bornstein, Paisley,1958-74 Paramounts x3, 3rensho, 74 Moto TC, 73-78 Raleigh Pro's x5, Marinoni x2, 1960 Cinelli SC, 1980 Bianchi SC, PX-10 X 2
Mentioned: 267 Post(s)
Tagged: 0 Thread(s)
Quoted: 4494 Post(s)
Liked 6,300 Times
in
3,633 Posts
Many of these are lucky to be this intact, taping it off may compromise even more, in any case it could be moot if it looks wrong after the rest is polished.
#3
Fixed on the plains.
Thread Starter
Yeah, that's what you get for running raced parts. I guess I was thinking that if I used an x-acto knife to cut the tape down to fit the logo perfectly it wouldn't be noticeable, but the more I think about it the more I'm not sure I could do that without further scratching up the crank arms. Do you suppose that spot near the pedal threads on the chainring side will polish up?
#4
Senior Member
Join Date: Oct 2015
Location: PDX
Posts: 14,101
Bikes: Merz x 5 + Specialized Merz Allez x 2, Strawberry/Newlands/DiNucci/Ti x3, Gordon, Fuso/Moulton x2, Bornstein, Paisley,1958-74 Paramounts x3, 3rensho, 74 Moto TC, 73-78 Raleigh Pro's x5, Marinoni x2, 1960 Cinelli SC, 1980 Bianchi SC, PX-10 X 2
Mentioned: 267 Post(s)
Tagged: 0 Thread(s)
Quoted: 4494 Post(s)
Liked 6,300 Times
in
3,633 Posts
Yeah, that's what you get for running raced parts. I guess I was thinking that if I used an x-acto knife to cut the tape down to fit the logo perfectly it wouldn't be noticeable, but the more I think about it the more I'm not sure I could do that without further scratching up the crank arms. Do you suppose that spot near the pedal threads on the chainring side will polish up?
#5
Fixed on the plains.
Thread Starter
Not really planning on completely redoing it, just making it look decent. If I could get away with buffing it and moving on that's exactly what I'd do.
Likes For LNKFixed:
#6
Senior Member
Join Date: Nov 2013
Location: Southern California
Posts: 1,626
Mentioned: 14 Post(s)
Tagged: 0 Thread(s)
Quoted: 780 Post(s)
Liked 727 Times
in
401 Posts
If I'm not mistaken I'm pretty sure branko_76 is pretty good at polishing parts? From what I've seen of his grand prix restorstion.
edit: I'm also of the opinion that they look fine.
edit: I'm also of the opinion that they look fine.
Last edited by Piff; 06-23-20 at 05:07 PM.
#8
Extraordinary Magnitude
Join Date: Aug 2009
Location: Waukesha WI
Posts: 13,640
Bikes: 1978 Trek TX700; 1978/79 Trek 736; 1984 Specialized Stumpjumper Sport; 1984 Schwinn Voyageur SP; 1985 Trek 620; 1985 Trek 720; 1986 Trek 400 Elance; 1987 Schwinn High Sierra; 1990 Miyata 1000LT
Mentioned: 84 Post(s)
Tagged: 0 Thread(s)
Quoted: 2597 Post(s)
Liked 1,678 Times
in
926 Posts
I’ve used clear nail polish over Suntour Cyclone, AR and Mountech screening. But that won’t protect against buffing or anything.
My guess is those cranks are anodized- I don’t think you’re taking the anodization off without taking off the lettering.
Here’s the ultimate Aluminum Polishing thread: https://www.bikeforums.net/classic-v...ng-thread.html
My guess is those cranks are anodized- I don’t think you’re taking the anodization off without taking off the lettering.
Here’s the ultimate Aluminum Polishing thread: https://www.bikeforums.net/classic-v...ng-thread.html
__________________
*Recipient of the 2006 Time Magazine "Person Of The Year" Award*
Commence to jigglin’ huh?!?!
"But hey, always love to hear from opinionated amateurs." -says some guy to Mr. Marshall.
Commence to jigglin’ huh?!?!
"But hey, always love to hear from opinionated amateurs." -says some guy to Mr. Marshall.
#9
Mother Nature's Son
Join Date: Mar 2016
Location: Sussex County, Delaware
Posts: 3,111
Bikes: 2014 Orbea Avant MD30, 2004 Airborne Zeppelin TI, 2003 Lemond Poprad, 2001 Lemond Tourmalet, 2014? Soma Smoothie
Mentioned: 14 Post(s)
Tagged: 0 Thread(s)
Quoted: 838 Post(s)
Liked 1,414 Times
in
801 Posts
I’ve used clear nail polish over Suntour Cyclone, AR and Mountech screening. But that won’t protect against buffing or anything.
My guess is those cranks are anodized- I don’t think you’re taking the anodization off without taking off the lettering.
Here’s the ultimate Aluminum Polishing thread: https://www.bikeforums.net/classic-v...ng-thread.html
My guess is those cranks are anodized- I don’t think you’re taking the anodization off without taking off the lettering.
Here’s the ultimate Aluminum Polishing thread: https://www.bikeforums.net/classic-v...ng-thread.html
The Golden Boy, thanks for posting this thread. I amy have to revisit some cranks that I tucked away.
#10
señor miembro
Join Date: Dec 2018
Location: Pac NW
Posts: 8,237
Bikes: '70s - '80s Campagnolo
Mentioned: 92 Post(s)
Tagged: 0 Thread(s)
Quoted: 3846 Post(s)
Liked 6,437 Times
in
3,183 Posts
Hard to tell how bad looking these are. The spider looks bad, but it may just be a reflection. If they really need polishing, you have to deanodize first, which will strip the black logo. It may be possible to cover the logo somehow while deanodizing. I've never tried that. If they're really bad, I might try to mask it off and give it a go. However, deanodizing and polishing are difficult enough without adding additional tasks like this. Another idea is to go ahead and fully polish and later apply a new decal that reproduces the logo.
Likes For SurferRosa:
#11
Senior Member
Join Date: Sep 2010
Location: La Habra, California
Posts: 820
Bikes: Italvega Super Speciales and Superlights
Mentioned: 33 Post(s)
Tagged: 0 Thread(s)
Quoted: 355 Post(s)
Liked 345 Times
in
174 Posts
I would agree with SurferRosa, do a good polishing and re-apply a new decal (if available). In regards to the area around the pedal eye, clean it up and lightly polish but be sure to use a pedal washer to evenly distribute the axial stress on the face of the threaded area. Makes future removal easier too. You are going to rehab the pedals too right?
__________________
Italvega and Torpado Enthusiast
Italvega and Torpado Enthusiast
#12
Senior Member
Join Date: Oct 2015
Location: PDX
Posts: 14,101
Bikes: Merz x 5 + Specialized Merz Allez x 2, Strawberry/Newlands/DiNucci/Ti x3, Gordon, Fuso/Moulton x2, Bornstein, Paisley,1958-74 Paramounts x3, 3rensho, 74 Moto TC, 73-78 Raleigh Pro's x5, Marinoni x2, 1960 Cinelli SC, 1980 Bianchi SC, PX-10 X 2
Mentioned: 267 Post(s)
Tagged: 0 Thread(s)
Quoted: 4494 Post(s)
Liked 6,300 Times
in
3,633 Posts
#13
Senior Member
Join Date: Jan 2015
Location: Los Angeles
Posts: 4,674
Bikes: 82 Medici, 2011 Richard Sachs, 2011 Milwaukee Road
Mentioned: 54 Post(s)
Tagged: 0 Thread(s)
Quoted: 1924 Post(s)
Liked 1,954 Times
in
1,086 Posts
They look great as is. Record, Dura Ace, and Superbe ALWAYS look great.
__________________
I don't do: disks, tubeless, e-shifting, or bead head nymphs.
I don't do: disks, tubeless, e-shifting, or bead head nymphs.
#14
Senior Member
Join Date: May 2019
Location: Bloomington, IN
Posts: 2,939
Bikes: Paramount, Faggin, Ochsner, Ciocc, Basso
Mentioned: 114 Post(s)
Tagged: 0 Thread(s)
Quoted: 1285 Post(s)
Liked 1,837 Times
in
1,110 Posts
Trying to clean these up will require removing the clear coat on the crank to get to the aluminum underneath. It will be a major undertaking to get right but if you do go that route I wish you luck. Smiles, MH
#15
Senior Member
Join Date: Oct 2011
Location: Fairplay Co
Posts: 9,582
Bikes: Current 79 Nishiki Custum Sport, Jeunet 620, notable previous bikes P.K. Ripper loop tail, Kawahara Laser Lite, Paramount Track full chrome, Raliegh Internatioanl, Motobecan Super Mirage. 59 Crown royak 3 speed
Mentioned: 26 Post(s)
Tagged: 1 Thread(s)
Quoted: 786 Post(s)
Liked 1,706 Times
in
620 Posts
I would just tape over the label then clean polish the cranks then take the tape off and do a light second cleaning polish with some wax.
#16
Senior Member
Join Date: Jun 2018
Location: The Urban Shores Of Michigami
Posts: 1,745
Bikes: ........................................ .....Holdsworth "Special"..... .......Falcon "Special".......... .........Miyata 912........... ........................................
Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 701 Post(s)
Liked 667 Times
in
417 Posts
If I'm not mistaken I'm pretty sure branko_76 is pretty good at polishing parts? From what I've seen of his grand prix restorstion.
edit: I'm also of the opinion that they look fine.
edit: I'm also of the opinion that they look fine.
For fragile finishes like anodized aluminum, I like to use NEVR-DULL wadding compound and then a micro-fiber cloth to buff it out. LNKFixed , I'm pretty sure the lettering was printed after the anodizing process so go lightly over it with whatever you decide to use.
Regarding that "Ultimate Aluminum Polishing" thread, it's pretty wordy but I didn't find a silver bullet. After years of experimenting with buffing wheels and compounds, I've found the safest and most efficient way to buff raw aluminum is a soft wire wheel mounted in a slow speed arbor, then a polishing compound, then buff with a micro-fiber cloth.
Likes For branko_76:
#17
Senior Member
Join Date: Jun 2018
Location: The Urban Shores Of Michigami
Posts: 1,745
Bikes: ........................................ .....Holdsworth "Special"..... .......Falcon "Special".......... .........Miyata 912........... ........................................
Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 701 Post(s)
Liked 667 Times
in
417 Posts
btw, LNKFixed , if you can let go of the lettering, you can make those crank arms look better than new.
Here are a couple of Shimano cranks, the 600 has the original anodized finish, the 105 was badly scratched so I used fine emery cloth to remove the scratches (and the anodizing), buffed it with a soft wire wheel, then NEVR-DULL, then micro-fiber cloth as I previously described.
600 crank with original anodized finish
105 crank after finish was removed, buffed and polished
Here are a couple of Shimano cranks, the 600 has the original anodized finish, the 105 was badly scratched so I used fine emery cloth to remove the scratches (and the anodizing), buffed it with a soft wire wheel, then NEVR-DULL, then micro-fiber cloth as I previously described.
600 crank with original anodized finish
105 crank after finish was removed, buffed and polished
Last edited by branko_76; 06-24-20 at 05:03 AM.