Centre-pull hangers are all too short, so...
#1
Senior Member
Thread Starter
Join Date: Feb 2020
Posts: 2,819
Mentioned: 49 Post(s)
Tagged: 0 Thread(s)
Quoted: 1106 Post(s)
Likes: 0
Liked 1,327 Times
in
783 Posts
Centre-pull hangers are all too short, so...
I made my own.
It's just a nut, drilled and tapped M6x1, silver-soldered to a bent spoke. It goes around the seatpost clamp bolt.
AND they all rust except the Mafac stainless ones - this won't: Brass and stainless and silver.
Anybody else want one?
It's just a nut, drilled and tapped M6x1, silver-soldered to a bent spoke. It goes around the seatpost clamp bolt.
AND they all rust except the Mafac stainless ones - this won't: Brass and stainless and silver.
Anybody else want one?
Likes For oneclick:
#2
Senior Member
Join Date: May 2008
Location: Fredericksburg, Va
Posts: 9,579
Bikes: '65 Frejus TDF, '73 Bottecchia Giro d'Italia, '83 Colnago Superissimo, '84 Trek 610, '84 Trek 760, '88 Pinarello Veneto, '88 De Rosa Pro, '89 Pinarello Montello, '94 Burley Duet, 97 Specialized RockHopper, 2010 Langster, Tern Link D8
Mentioned: 73 Post(s)
Tagged: 0 Thread(s)
Quoted: 1607 Post(s)
Liked 2,216 Times
in
1,103 Posts
@oneclick - Show us the application please.
__________________
Bikes don't stand alone. They are two tired.
Bikes don't stand alone. They are two tired.
Likes For oneclick:
#4
Senior Member
Join Date: Apr 2011
Location: Maryland, USA
Posts: 2,433
Bikes: Drysdale/Gitane/Zeus/Masi/Falcon/Palo Alto/Raleigh/Legnano
Mentioned: 34 Post(s)
Tagged: 0 Thread(s)
Quoted: 983 Post(s)
Liked 631 Times
in
402 Posts
Great idea for thinking outside the box. Hmm, I have no idea what the tension load is on the part under hard braking... those connections will hold?
__________________
Larry:1958 Drysdale, 1961 Gitane Gran Sport, 1974 Zeus track, 1988 Masi Gran Corsa, 1974 Falcon, 1980 Palo Alto, 1973 Raleigh Gran Sport, 1974 Legnano. Susan: 1976 Windsor Profesional.
Larry:1958 Drysdale, 1961 Gitane Gran Sport, 1974 Zeus track, 1988 Masi Gran Corsa, 1974 Falcon, 1980 Palo Alto, 1973 Raleigh Gran Sport, 1974 Legnano. Susan: 1976 Windsor Profesional.
#5
Full Member
Join Date: Feb 2010
Location: Tucson, AZ
Posts: 303
Bikes: Raleigh Competition GS, Freschi Supreme, Miyata 1000, Trek 520, Marin Pine Mountain, Specialized RockCombo, Soma Smoothie, Surly Cross-Check
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 99 Post(s)
Liked 267 Times
in
105 Posts
Likes For squarenoise:
#6
Stop reading my posts!
Join Date: Sep 2004
Posts: 12,582
Mentioned: 90 Post(s)
Tagged: 0 Thread(s)
Quoted: 1443 Post(s)
Liked 1,062 Times
in
787 Posts
I also would like to see how it installs, but yes, I am interested! Always appreciate it when C&Vers are also skilled DIYers, we have had many examples over the years!
#7
buy my bikes
Join Date: Jun 2014
Location: Michigan
Posts: 1,800
Bikes: my very own customized GUNNAR CrossHairs
Mentioned: 19 Post(s)
Tagged: 0 Thread(s)
Quoted: 519 Post(s)
Liked 428 Times
in
249 Posts
the SURLY looks like a weld. The OP is using a braze.
It would be easy enough to insert a bolt and pull on it test it. I'm guessing a person could go full 200lb of body weight on the SURLY welded part and just hang out for a good long time.
A possible improvement to the OP's hack would be a tall nut to get more brazed length. Maybe bend the spoke around the nut a bit. Maybe put a flat on the spoke to get more surface area.
Found this trying to get a best guess on brazed joint shear strength: https://lucasmilhaupt.com/EN/Brazing...ndamentals.htm
see table 1 here: https://app.aws.org/wj/supplement/WJ_1975_08_s276.pdf
... next question: fatigue cycles associated with braking (which would lead to breaking....)
i should really get back to work....
anyway, I'll vote HACK (not a bodge.....)
cheers.
It would be easy enough to insert a bolt and pull on it test it. I'm guessing a person could go full 200lb of body weight on the SURLY welded part and just hang out for a good long time.
A possible improvement to the OP's hack would be a tall nut to get more brazed length. Maybe bend the spoke around the nut a bit. Maybe put a flat on the spoke to get more surface area.
Found this trying to get a best guess on brazed joint shear strength: https://lucasmilhaupt.com/EN/Brazing...ndamentals.htm
see table 1 here: https://app.aws.org/wj/supplement/WJ_1975_08_s276.pdf
... next question: fatigue cycles associated with braking (which would lead to breaking....)
i should really get back to work....
anyway, I'll vote HACK (not a bodge.....)
cheers.
Likes For mrv:
#8
Senior Member
Join Date: May 2008
Location: Fredericksburg, Va
Posts: 9,579
Bikes: '65 Frejus TDF, '73 Bottecchia Giro d'Italia, '83 Colnago Superissimo, '84 Trek 610, '84 Trek 760, '88 Pinarello Veneto, '88 De Rosa Pro, '89 Pinarello Montello, '94 Burley Duet, 97 Specialized RockHopper, 2010 Langster, Tern Link D8
Mentioned: 73 Post(s)
Tagged: 0 Thread(s)
Quoted: 1607 Post(s)
Liked 2,216 Times
in
1,103 Posts
__________________
Bikes don't stand alone. They are two tired.
Bikes don't stand alone. They are two tired.
#9
Team Beer
Join Date: Apr 2004
Location: Sacramento CA
Posts: 6,339
Bikes: Too Many
Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 114 Post(s)
Liked 159 Times
in
104 Posts
I've made several of these with spokes and cable stop braze-ons. They are perfectly strong. To the OP, nice thinking on using a brass nut.
__________________
I'm not one for fawning over bicycles, but I do believe that our bikes communicate with us, and what this bike is saying is, "You're an idiot." BikeSnobNYC
I'm not one for fawning over bicycles, but I do believe that our bikes communicate with us, and what this bike is saying is, "You're an idiot." BikeSnobNYC
Likes For Cynikal:
Likes For oneclick:
#11
Senior Member
Join Date: May 2008
Location: Fredericksburg, Va
Posts: 9,579
Bikes: '65 Frejus TDF, '73 Bottecchia Giro d'Italia, '83 Colnago Superissimo, '84 Trek 610, '84 Trek 760, '88 Pinarello Veneto, '88 De Rosa Pro, '89 Pinarello Montello, '94 Burley Duet, 97 Specialized RockHopper, 2010 Langster, Tern Link D8
Mentioned: 73 Post(s)
Tagged: 0 Thread(s)
Quoted: 1607 Post(s)
Liked 2,216 Times
in
1,103 Posts
Good work!
__________________
Bikes don't stand alone. They are two tired.
Bikes don't stand alone. They are two tired.
#12
Not lost wanderer.
Join Date: Jan 2013
Location: Lititz, Pa
Posts: 3,327
Bikes: In USA; 73 Raleigh Super Course dingle speed, 72 Raleigh Gran Sport SS, 72 Geoffry Butler, 81 Centurion Pro-Tour, 74 Gugie Grandier Sportier
Mentioned: 72 Post(s)
Tagged: 0 Thread(s)
Quoted: 885 Post(s)
Liked 990 Times
in
522 Posts
I would take 2 or 3
#13
Senior Member
Thread Starter
Join Date: Feb 2020
Posts: 2,819
Mentioned: 49 Post(s)
Tagged: 0 Thread(s)
Quoted: 1106 Post(s)
Likes: 0
Liked 1,327 Times
in
783 Posts
How about 3 of Mk III (pictured below) for $30 and I'll pay postage. You only get the hanger, you'll have to supply your own adjuster.
This one has the plain nut, but it has two holes cross-drilled into the edges and the spoke is bent 90 degrees and silver-soldered into the holes. I think this is (so far) the best solution, it's lighter than Mk II, the thread engagement for the adjuster is longer. It's a 2mm spoke, if you have a seat-lug with a show-off thin kerf it may not fit; I can make one with a thinner spoke if that's the case.
Just to be clear, this is *real* silver solder, the same as used in jewellery, not that "silver-bearing" stuff sold in hardware stores. It melts at medium-red heat and has a bulk UTS of around 50 KSI, the hardware stuff you can do with a soldering iron and is more like 10 KSI. It's not coming apart.
This one has the plain nut, but it has two holes cross-drilled into the edges and the spoke is bent 90 degrees and silver-soldered into the holes. I think this is (so far) the best solution, it's lighter than Mk II, the thread engagement for the adjuster is longer. It's a 2mm spoke, if you have a seat-lug with a show-off thin kerf it may not fit; I can make one with a thinner spoke if that's the case.
Just to be clear, this is *real* silver solder, the same as used in jewellery, not that "silver-bearing" stuff sold in hardware stores. It melts at medium-red heat and has a bulk UTS of around 50 KSI, the hardware stuff you can do with a soldering iron and is more like 10 KSI. It's not coming apart.
Last edited by oneclick; 11-25-20 at 09:17 AM.
#14
multimodal commuter
Join Date: Nov 2006
Location: NJ, NYC, LI
Posts: 19,808
Bikes: 1940s Fothergill, 1959 Allegro Special, 1963? Claud Butler Olympic Sprint, Lambert 'Clubman', 1974 Fuji "the Ace", 1976 Holdsworth 650b conversion rando bike, 1983 Trek 720 tourer, 1984 Counterpoint Opus II, 1993 Basso Gap, 2010 Downtube 8h, and...
Mentioned: 584 Post(s)
Tagged: 0 Thread(s)
Quoted: 1908 Post(s)
Liked 574 Times
in
339 Posts
I made something similar for my Holdsworth Gugifacazione, but instead of a nut soldered to the spoke, i have a piece of aluminum. The ends of the spoke go all the way through the aluminum piece and are then bent to a J shape, the end of which goes back into a second hole in the aluminum. Ive used this for a few years, no problems.
Last edited by rhm; 11-27-20 at 01:23 PM.
#15
Senior Member
Thread Starter
Join Date: Feb 2020
Posts: 2,819
Mentioned: 49 Post(s)
Tagged: 0 Thread(s)
Quoted: 1106 Post(s)
Likes: 0
Liked 1,327 Times
in
783 Posts
Mk IV prototype...
This was too much trouble to make the way it is. If I do anymore like this it'll probably just have a separate ring, not be formed from one piece:
Likes For oneclick:
#16
Full Member
Join Date: Feb 2010
Location: Tucson, AZ
Posts: 303
Bikes: Raleigh Competition GS, Freschi Supreme, Miyata 1000, Trek 520, Marin Pine Mountain, Specialized RockCombo, Soma Smoothie, Surly Cross-Check
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 99 Post(s)
Liked 267 Times
in
105 Posts
Now THIS is a great upgrade!! Such a smart/elegant solution to help alight the cable housing and relieve that pressure right at the adjuster.
Likes For squarenoise:
#17
Senior Member
Thread Starter
Join Date: Feb 2020
Posts: 2,819
Mentioned: 49 Post(s)
Tagged: 0 Thread(s)
Quoted: 1106 Post(s)
Likes: 0
Liked 1,327 Times
in
783 Posts
I made something similar for my Holdsworth Gugifacazione, but instead of a nut soldered to the spoke, i have a piece of aluminum. The ends of the spoke go all the way through the aluminum piece and are then bent to a J shape, the end of which goes back into a second hole in the aluminum. Ive used this for a few years, no problems.
But maybe something like this would keep that cable-outer from rubbing:
Last edited by oneclick; 11-28-20 at 01:06 PM.
#19
Senior Member
Join Date: Apr 2011
Location: Maryland, USA
Posts: 2,433
Bikes: Drysdale/Gitane/Zeus/Masi/Falcon/Palo Alto/Raleigh/Legnano
Mentioned: 34 Post(s)
Tagged: 0 Thread(s)
Quoted: 983 Post(s)
Liked 631 Times
in
402 Posts
Or mount the locknut underneath?
__________________
Larry:1958 Drysdale, 1961 Gitane Gran Sport, 1974 Zeus track, 1988 Masi Gran Corsa, 1974 Falcon, 1980 Palo Alto, 1973 Raleigh Gran Sport, 1974 Legnano. Susan: 1976 Windsor Profesional.
Larry:1958 Drysdale, 1961 Gitane Gran Sport, 1974 Zeus track, 1988 Masi Gran Corsa, 1974 Falcon, 1980 Palo Alto, 1973 Raleigh Gran Sport, 1974 Legnano. Susan: 1976 Windsor Profesional.
#20
Senior Member
Thread Starter
Join Date: Feb 2020
Posts: 2,819
Mentioned: 49 Post(s)
Tagged: 0 Thread(s)
Quoted: 1106 Post(s)
Likes: 0
Liked 1,327 Times
in
783 Posts
I do have a nice little channel-lock-type set of pliers, the jaws are about 3/32" thick and about 3/4" long, it works no matter where the adjuster is.
#21
www.theheadbadge.com
Join Date: Sep 2005
Location: Southern Florida
Posts: 28,513
Bikes: https://www.theheadbadge.com
Mentioned: 124 Post(s)
Tagged: 0 Thread(s)
Quoted: 2422 Post(s)
Liked 4,391 Times
in
2,092 Posts
#22
Ride, Wrench, Swap, Race
Join Date: Jan 2010
Location: Northern California
Posts: 9,193
Bikes: Cheltenham-Pedersen racer, Boulder F/S Paris-Roubaix, Varsity racer, '52 Christophe, '62 Continental, '92 Merckx, '75 Limongi, '76 Presto, '72 Gitane SC, '71 Schwinn SS, etc.
Mentioned: 132 Post(s)
Tagged: 0 Thread(s)
Quoted: 1565 Post(s)
Liked 1,295 Times
in
865 Posts
Old cable housing adjusters had mere knurling on their (usually round) locknut, so didn't rely on anything more than finger-tightening.
I find that they tend never to loosen on their own!
I find that they tend never to loosen on their own!
#23
Senior Member
Thread Starter
Join Date: Feb 2020
Posts: 2,819
Mentioned: 49 Post(s)
Tagged: 0 Thread(s)
Quoted: 1106 Post(s)
Likes: 0
Liked 1,327 Times
in
783 Posts
5mm/wingnut version
I had to get more brass nuts to make more of these things. I knew that the flat nuts I had would not work for a 5mm adjuster; either the existing hole was too big or the nut outside was too small. Then I saw my local hardware store had 8-32 brass wingnuts:
The nut costs more but that's not a big factor, it's just as easy to make. I got some 10-24 wingnuts and will make a few 6mm versions like this.
The nut costs more but that's not a big factor, it's just as easy to make. I got some 10-24 wingnuts and will make a few 6mm versions like this.