Why would KMC say this?
#1
Senior Member
Thread Starter
Join Date: Jan 2013
Posts: 2,721
Bikes: too many sparkly Italians, some sweet Americans and a couple interesting Japanese
Mentioned: 10 Post(s)
Tagged: 0 Thread(s)
Quoted: 574 Post(s)
Liked 615 Times
in
424 Posts
Why would KMC say this?
One of my son-in-laws only brushes & wipes his chains, never would soak or use my Ultrasonic Cleaner as KMC on the web site says "DO NOT dip your chain in (aggressive) degreasers - they remove the remaining grease from the chain’s parts, and may cause cracks." on https://www.kmcchain.com/en/teach/ma...nce-bike-chain. Assuming OMS is an aggressive degreaser to KMC I am mystified by "cracks" and curious the basis of this as surely they want good life from their chains. Can it be that the average cyclist is incapable of keeping a chain lubed and needs factory grease to last a lifetime?
#2
Senior Member
Join Date: May 2003
Location: Mountain Brook. AL
Posts: 4,003
Mentioned: 14 Post(s)
Tagged: 0 Thread(s)
Quoted: 303 Post(s)
Likes: 0
Liked 137 Times
in
105 Posts
Probably a reflection of the POV expressed in this article: https://silca.cc/blogs/silca/hydroge...-break-a-chain
FWIW I used a pHydrion 1-13 range pH strip to check pH of red wine vinegar = 4, of Simple Green purchased at Sam's about 15 yrs ago
and pH was ~9, finally Palmolive Ultra Strength dish soap pH ~4. Acidic pH is somewhat more likely to "hydrogen embrittle" than alkaline
pH, but the effects of aqueous solutions on hydrogen embrittlement of steel at normal temps (under the boiling point) and pressures of atmospheric
are extremely small. It is primarily a problem at welding temperatures which are high enough to turn H20 into plasma.
FWIW I used a pHydrion 1-13 range pH strip to check pH of red wine vinegar = 4, of Simple Green purchased at Sam's about 15 yrs ago
and pH was ~9, finally Palmolive Ultra Strength dish soap pH ~4. Acidic pH is somewhat more likely to "hydrogen embrittle" than alkaline
pH, but the effects of aqueous solutions on hydrogen embrittlement of steel at normal temps (under the boiling point) and pressures of atmospheric
are extremely small. It is primarily a problem at welding temperatures which are high enough to turn H20 into plasma.
Last edited by sch; 01-13-24 at 11:51 AM. Reason: reversed acid/base effects
Likes For sch:
Likes For Mr. 66:
Likes For easyupbug:
#5
Thread derailleur
Join Date: Mar 2004
Location: Glendora, CA
Posts: 668
Bikes: Croll '94 & Cannondale Supersix '15
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 378 Post(s)
Liked 480 Times
in
276 Posts
Long-time KMC high-end chain user here. Never did anything more than lightly wipe it after each lube.
Over 6k miles lifespan from every single one. Love 'em!
Over 6k miles lifespan from every single one. Love 'em!
#6
Method to My Madness
Join Date: Nov 2020
Location: Orange County, California
Posts: 3,867
Bikes: Trek FX 2, Cannondale Synapse x2, Cannondale CAAD4, Santa Cruz Stigmata 3
Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 2068 Post(s)
Liked 1,561 Times
in
1,082 Posts
That is the same Silca article that had (for a few months) used my photo (below) without permission.
(I believed that) I had damaged the original 105 chain (CN-HG600) on my bike for letting it soak overnight in purple degreaser.
cyccommute can explain in greater detail, but purple degreaser is basically a strong base in an aqueous solution, whereas odorless mineral spirits is an organic solvent refined from petroleum byproducts. Only the former carries a risk of hydrogen embrittlement.
(I believed that) I had damaged the original 105 chain (CN-HG600) on my bike for letting it soak overnight in purple degreaser.
cyccommute can explain in greater detail, but purple degreaser is basically a strong base in an aqueous solution, whereas odorless mineral spirits is an organic solvent refined from petroleum byproducts. Only the former carries a risk of hydrogen embrittlement.
Likes For SoSmellyAir:
#7
Senior Member
Join Date: Apr 2009
Location: New Rochelle, NY
Posts: 39,054
Bikes: too many bikes from 1967 10s (5x2)Frejus to a Sumitomo Ti/Chorus aluminum 10s (10x2), plus one non-susp mtn bike I use as my commuter
Mentioned: 141 Post(s)
Tagged: 1 Thread(s)
Quoted: 5971 Post(s)
Liked 2,878 Times
in
1,602 Posts
The reference to caustic cleaners and fracture relates to radicals, ie. hydrogen or chlorine, which can migrate into the steel and degrade the crystal structure.
So, while typical petroleum solvent are fine, many aggressive cleaners are not. Not being able to list every problem cleaner out there KMC puts in a blanket warning.
Also consider that chain companies spend serious dough to provide chains with lubricants that will maximize chain life. Most people who diligently strip these lubes end up replacing it with something not nearly as good. IMO, if you change the lube, you forfeit, to an extent, the right to complain about chain life.
So, while typical petroleum solvent are fine, many aggressive cleaners are not. Not being able to list every problem cleaner out there KMC puts in a blanket warning.
Also consider that chain companies spend serious dough to provide chains with lubricants that will maximize chain life. Most people who diligently strip these lubes end up replacing it with something not nearly as good. IMO, if you change the lube, you forfeit, to an extent, the right to complain about chain life.
Last edited by FBinNY; 01-14-24 at 11:11 AM.
#8
Mad bike riding scientist
Join Date: Nov 2004
Location: Denver, CO
Posts: 27,478
Bikes: Some silver ones, a red one, a black and orange one, and a few titanium ones
Mentioned: 153 Post(s)
Tagged: 1 Thread(s)
Quoted: 6278 Post(s)
Liked 4,322 Times
in
2,421 Posts
What do you think “degreasing” is or how it is accomplished? If you use a water based “degreaser” or mineral spirits, you are using a solvent to remove the grease.
__________________
Stuart Black
Plan Epsilon Around Lake Michigan in the era of Covid
Old School…When It Wasn’t Ancient bikepacking
Gold Fever Three days of dirt in Colorado
Pokin' around the Poconos A cold ride around Lake Erie
Dinosaurs in Colorado A mountain bike guide to the Purgatory Canyon dinosaur trackway
Solo Without Pie. The search for pie in the Midwest.
Picking the Scablands. Washington and Oregon, 2005. Pie and spiders on the Columbia River!
Stuart Black
Plan Epsilon Around Lake Michigan in the era of Covid
Old School…When It Wasn’t Ancient bikepacking
Gold Fever Three days of dirt in Colorado
Pokin' around the Poconos A cold ride around Lake Erie
Dinosaurs in Colorado A mountain bike guide to the Purgatory Canyon dinosaur trackway
Solo Without Pie. The search for pie in the Midwest.
Picking the Scablands. Washington and Oregon, 2005. Pie and spiders on the Columbia River!
#9
Mad bike riding scientist
Join Date: Nov 2004
Location: Denver, CO
Posts: 27,478
Bikes: Some silver ones, a red one, a black and orange one, and a few titanium ones
Mentioned: 153 Post(s)
Tagged: 1 Thread(s)
Quoted: 6278 Post(s)
Liked 4,322 Times
in
2,421 Posts
One of my son-in-laws only brushes & wipes his chains, never would soak or use my Ultrasonic Cleaner as KMC on the web site says "DO NOT dip your chain in (aggressive) degreasers - they remove the remaining grease from the chain’s parts, and may cause cracks." on https://www.kmcchain.com/en/teach/ma...nce-bike-chain. Assuming OMS is an aggressive degreaser to KMC I am mystified by "cracks" and curious the basis of this as surely they want good life from their chains. Can it be that the average cyclist is incapable of keeping a chain lubed and needs factory grease to last a lifetime?
Mineral spirits…real mineral spirits, not the water based “green” ones…have no effect on metal parts and little effect on most plastic parts.
Green mineral spirits is a very different animal and could lead to cracking if a salt contaminated chain is soaked in it. Several years ago I demonstrated how this could happen. (Please don’t resurrect this very old thread) If you don’t want to wade through the whole thread, Here’s the result of the Great Chain Corrosion Experiment of 2011.
__________________
Stuart Black
Plan Epsilon Around Lake Michigan in the era of Covid
Old School…When It Wasn’t Ancient bikepacking
Gold Fever Three days of dirt in Colorado
Pokin' around the Poconos A cold ride around Lake Erie
Dinosaurs in Colorado A mountain bike guide to the Purgatory Canyon dinosaur trackway
Solo Without Pie. The search for pie in the Midwest.
Picking the Scablands. Washington and Oregon, 2005. Pie and spiders on the Columbia River!
Stuart Black
Plan Epsilon Around Lake Michigan in the era of Covid
Old School…When It Wasn’t Ancient bikepacking
Gold Fever Three days of dirt in Colorado
Pokin' around the Poconos A cold ride around Lake Erie
Dinosaurs in Colorado A mountain bike guide to the Purgatory Canyon dinosaur trackway
Solo Without Pie. The search for pie in the Midwest.
Picking the Scablands. Washington and Oregon, 2005. Pie and spiders on the Columbia River!
Likes For cyccommute:
#10
Newbie
Join Date: Jan 2024
Posts: 4
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 3 Times
in
2 Posts
FWIW I use an ultrasonic cleaner to clean my chains and the solution is Lyman Turbo Sonic Steel and Gun Parts Cleaning Solution. It does a great job on the chains without any issues.
I figured it's not causing any problems with my guns - metal and plastic - and it isn't causing any problems with my chains.
I give the chains a good soaking in chain lube, wiping them off, reinstalling, operate the bikes through their gears before running another cloth over the chains.
Works for me but YMMV.
I figured it's not causing any problems with my guns - metal and plastic - and it isn't causing any problems with my chains.
I give the chains a good soaking in chain lube, wiping them off, reinstalling, operate the bikes through their gears before running another cloth over the chains.
Works for me but YMMV.
#12
Senior Member
Join Date: Sep 2004
Location: Chicago area
Posts: 2,577
Bikes: Airborne "Carpe Diem", Motobecane "Mirage", Trek 6000, Strida 2, Dahon "Helios XL", Dahon "Mu XL", Tern "Verge S11i"
Mentioned: 23 Post(s)
Tagged: 0 Thread(s)
Quoted: 996 Post(s)
Liked 592 Times
in
406 Posts
Of possible relevance is this experience. It's not chain-related, but has to do with the effects of strong chemicals on stressed metal.
I had a set of couplers for MKS pedals. The couplers were quite rusty (why they were not stainless steel is a good question), so I soaked them in Naval Jelly (phosphoric acid gel) until the rust was gone... overnight as I remember. Not more than a few hundred miles later, one of the couplers fell apart. The other was cracked and on the way to failure. I have two other pairs of these couplers which have accumulated at least as many miles, but show no signs of failure. I have avoided the use of Naval Jelly on them.
This coupler is not failing, but is disassembled for cleaning and replacement of the ball bearings. No H3PO4 was used.
This coupler was soaked in H3PO4 for rust removal. The cracks were discovered after the other coupler fell apart.
I had a set of couplers for MKS pedals. The couplers were quite rusty (why they were not stainless steel is a good question), so I soaked them in Naval Jelly (phosphoric acid gel) until the rust was gone... overnight as I remember. Not more than a few hundred miles later, one of the couplers fell apart. The other was cracked and on the way to failure. I have two other pairs of these couplers which have accumulated at least as many miles, but show no signs of failure. I have avoided the use of Naval Jelly on them.
This coupler is not failing, but is disassembled for cleaning and replacement of the ball bearings. No H3PO4 was used.
This coupler was soaked in H3PO4 for rust removal. The cracks were discovered after the other coupler fell apart.
#13
Senior Member
Removal of rust by phosphoric acid is going to leave the surface rough - not a good idea to use on surfaces that must be smooth, such as ball bearing and their races.
As for why not the stainless steel, the answer is always money!
As for why not the stainless steel, the answer is always money!
Likes For Alan K:
#14
SE Wis
Join Date: Apr 2005
Location: Milwaukee, WI
Posts: 10,557
Bikes: '68 Raleigh Sprite, '02 Raleigh C500, '84 Raleigh Gran Prix, '91 Trek 400, 2013 Novara Randonee, 1990 Trek 970
Mentioned: 40 Post(s)
Tagged: 0 Thread(s)
Quoted: 2755 Post(s)
Liked 3,427 Times
in
2,075 Posts
#16
Mad bike riding scientist
Join Date: Nov 2004
Location: Denver, CO
Posts: 27,478
Bikes: Some silver ones, a red one, a black and orange one, and a few titanium ones
Mentioned: 153 Post(s)
Tagged: 1 Thread(s)
Quoted: 6278 Post(s)
Liked 4,322 Times
in
2,421 Posts
That’s mostly because people don’t understand chemistry. Safety Klean parts washers use mineral spirits in some applications and calls the solvent a degreaser. Anything that dissolves grease is a “degreaser”. Mineral spirits is actually a whole lot better at “degreasing” than water based degreasers are.
__________________
Stuart Black
Plan Epsilon Around Lake Michigan in the era of Covid
Old School…When It Wasn’t Ancient bikepacking
Gold Fever Three days of dirt in Colorado
Pokin' around the Poconos A cold ride around Lake Erie
Dinosaurs in Colorado A mountain bike guide to the Purgatory Canyon dinosaur trackway
Solo Without Pie. The search for pie in the Midwest.
Picking the Scablands. Washington and Oregon, 2005. Pie and spiders on the Columbia River!
Stuart Black
Plan Epsilon Around Lake Michigan in the era of Covid
Old School…When It Wasn’t Ancient bikepacking
Gold Fever Three days of dirt in Colorado
Pokin' around the Poconos A cold ride around Lake Erie
Dinosaurs in Colorado A mountain bike guide to the Purgatory Canyon dinosaur trackway
Solo Without Pie. The search for pie in the Midwest.
Picking the Scablands. Washington and Oregon, 2005. Pie and spiders on the Columbia River!
#17
Mad bike riding scientist
Join Date: Nov 2004
Location: Denver, CO
Posts: 27,478
Bikes: Some silver ones, a red one, a black and orange one, and a few titanium ones
Mentioned: 153 Post(s)
Tagged: 1 Thread(s)
Quoted: 6278 Post(s)
Liked 4,322 Times
in
2,421 Posts
Of possible relevance is this experience. It's not chain-related, but has to do with the effects of strong chemicals on stressed metal.
I had a set of couplers for MKS pedals. The couplers were quite rusty (why they were not stainless steel is a good question), so I soaked them in Naval Jelly (phosphoric acid gel) until the rust was gone... overnight as I remember. Not more than a few hundred miles later, one of the couplers fell apart. The other was cracked and on the way to failure. I have two other pairs of these couplers which have accumulated at least as many miles, but show no signs of failure. I have avoided the use of Naval Jelly on them.
This coupler is not failing, but is disassembled for cleaning and replacement of the ball bearings. No H3PO4 was used.
This coupler was soaked in H3PO4 for rust removal. The cracks were discovered after the other coupler fell apart.
I had a set of couplers for MKS pedals. The couplers were quite rusty (why they were not stainless steel is a good question), so I soaked them in Naval Jelly (phosphoric acid gel) until the rust was gone... overnight as I remember. Not more than a few hundred miles later, one of the couplers fell apart. The other was cracked and on the way to failure. I have two other pairs of these couplers which have accumulated at least as many miles, but show no signs of failure. I have avoided the use of Naval Jelly on them.
This coupler is not failing, but is disassembled for cleaning and replacement of the ball bearings. No H3PO4 was used.
This coupler was soaked in H3PO4 for rust removal. The cracks were discovered after the other coupler fell apart.
There was more rust on the back so the paint lifted more but the front of the plate came out quite nice.
It comes in huge quantities and can be reused. I took some to the co-op for treating rusty bolts we have around the shop and they came out super shiny. It uses what is call a celating agent to remove the rust. It can cause graying of some parts that have been coated with other metals. Make sure you rinse the parts after soaking and dry them quickly or else they will rust as they dry. I use denatured alcohol.
__________________
Stuart Black
Plan Epsilon Around Lake Michigan in the era of Covid
Old School…When It Wasn’t Ancient bikepacking
Gold Fever Three days of dirt in Colorado
Pokin' around the Poconos A cold ride around Lake Erie
Dinosaurs in Colorado A mountain bike guide to the Purgatory Canyon dinosaur trackway
Solo Without Pie. The search for pie in the Midwest.
Picking the Scablands. Washington and Oregon, 2005. Pie and spiders on the Columbia River!
Stuart Black
Plan Epsilon Around Lake Michigan in the era of Covid
Old School…When It Wasn’t Ancient bikepacking
Gold Fever Three days of dirt in Colorado
Pokin' around the Poconos A cold ride around Lake Erie
Dinosaurs in Colorado A mountain bike guide to the Purgatory Canyon dinosaur trackway
Solo Without Pie. The search for pie in the Midwest.
Picking the Scablands. Washington and Oregon, 2005. Pie and spiders on the Columbia River!
Likes For cyccommute:
Likes For rydabent:
#19
Mad bike riding scientist
Join Date: Nov 2004
Location: Denver, CO
Posts: 27,478
Bikes: Some silver ones, a red one, a black and orange one, and a few titanium ones
Mentioned: 153 Post(s)
Tagged: 1 Thread(s)
Quoted: 6278 Post(s)
Liked 4,322 Times
in
2,421 Posts
Because "plain old kerosene" isn't a readily available as it once was. 40 years ago, you might have been able to get kerosene at just about any corner gas station. Today, you have to seek out somewhere that carries. Mineral spirits are more readily available and come in smaller volumes
__________________
Stuart Black
Plan Epsilon Around Lake Michigan in the era of Covid
Old School…When It Wasn’t Ancient bikepacking
Gold Fever Three days of dirt in Colorado
Pokin' around the Poconos A cold ride around Lake Erie
Dinosaurs in Colorado A mountain bike guide to the Purgatory Canyon dinosaur trackway
Solo Without Pie. The search for pie in the Midwest.
Picking the Scablands. Washington and Oregon, 2005. Pie and spiders on the Columbia River!
Stuart Black
Plan Epsilon Around Lake Michigan in the era of Covid
Old School…When It Wasn’t Ancient bikepacking
Gold Fever Three days of dirt in Colorado
Pokin' around the Poconos A cold ride around Lake Erie
Dinosaurs in Colorado A mountain bike guide to the Purgatory Canyon dinosaur trackway
Solo Without Pie. The search for pie in the Midwest.
Picking the Scablands. Washington and Oregon, 2005. Pie and spiders on the Columbia River!
#20
Senior Member
#21
Senior Member
Join Date: Nov 2022
Location: California's capital
Posts: 514
Bikes: Litespeed Firenze, Spot Acme, Specialzed S Works Pro Race, Davidson Stiletto, Colnago Superissimo
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 147 Post(s)
Liked 324 Times
in
189 Posts
I suppose the deodorized lamp oils you can buy would be kerosene-adjacent.
#22
Newbie
Every single diesel engine injection system relies on diesel fuel as a lubricant to protect and lubricate all the moving parts within the fuel system including injectors, in-line pumps and injection pumps.
diesel fuel is readily available!!!
those pumps are under a lot of pressure compared to bike chains
diesel fuel is readily available!!!
those pumps are under a lot of pressure compared to bike chains
Likes For Billlyy:
#23
Mad bike riding scientist
Join Date: Nov 2004
Location: Denver, CO
Posts: 27,478
Bikes: Some silver ones, a red one, a black and orange one, and a few titanium ones
Mentioned: 153 Post(s)
Tagged: 1 Thread(s)
Quoted: 6278 Post(s)
Liked 4,322 Times
in
2,421 Posts
It's not super common now but "white gas" for camping gear works well, e.g., Coleman fuel. Harder to find now that canister stoves and lanterns have taken over the market. Weirdly, the MDS shows different mixes of petroleum distillates depending on country, but in my experience it leaves no residue or "fragrance" like kerosene regardless of brand, plus evaporates quickly.
I suppose the deodorized lamp oils you can buy would be kerosene-adjacent.
I suppose the deodorized lamp oils you can buy would be kerosene-adjacent.
__________________
Stuart Black
Plan Epsilon Around Lake Michigan in the era of Covid
Old School…When It Wasn’t Ancient bikepacking
Gold Fever Three days of dirt in Colorado
Pokin' around the Poconos A cold ride around Lake Erie
Dinosaurs in Colorado A mountain bike guide to the Purgatory Canyon dinosaur trackway
Solo Without Pie. The search for pie in the Midwest.
Picking the Scablands. Washington and Oregon, 2005. Pie and spiders on the Columbia River!
Stuart Black
Plan Epsilon Around Lake Michigan in the era of Covid
Old School…When It Wasn’t Ancient bikepacking
Gold Fever Three days of dirt in Colorado
Pokin' around the Poconos A cold ride around Lake Erie
Dinosaurs in Colorado A mountain bike guide to the Purgatory Canyon dinosaur trackway
Solo Without Pie. The search for pie in the Midwest.
Picking the Scablands. Washington and Oregon, 2005. Pie and spiders on the Columbia River!
Likes For cyccommute:
#24
Full Member
If OMS was in any way harmful to metal, I doubt it would be sold in metal cans. It is a wonderful solvent, relatively cheap, not as toxic or flammable as some other solvents and it is readily available. Why look for anything else?
Last edited by flanso; 01-15-24 at 03:56 PM. Reason: spelling error
Likes For flanso:
#25
Senior Member
Join Date: Apr 2019
Location: UK
Posts: 1,417
Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 688 Post(s)
Liked 459 Times
in
343 Posts
That other thread was interesting. Funny how some people can’t get their head around chemistry and keep trying to come up with physical causes because that’s much more intuitive.
Also: 1100 miles to break a 10speed chain. Must be something went on there.
Also: 1100 miles to break a 10speed chain. Must be something went on there.