Original Hyperglide Chain Connector Pin Removal & Reinstallation?
#1
only here for the "LIKES"
Thread Starter
Join Date: Nov 2004
Location: squirrel cage of anxiety and delusion
Posts: 483
Mentioned: 143 Post(s)
Tagged: 0 Thread(s)
Quoted: 1644 Post(s)
Likes: 0
Liked 2,244 Times
in
1,053 Posts
Original Hyperglide Chain Connector Pin Removal & Reinstallation?
7 speed, Hyperglide cassette rear hub.
I want to break the low mileage original Hyperglide chain on my Bridgestone. It still has the factory waxy type coating on it, but it is very dusty from having sat around for the better part of 3 decades.
I want to remove the chain to do a thorough deep cleaning, probably a wax lube, then reinstall the chain.
One of the pins is noticeably different from the others, see pic. I am presuming this is the original connector pin, and I'd like to maintain as much originality on the bike as possible. If I drive this pin out, can I reinstall it?
Or would I be better off picking a different spot on the chain to remove a pin/link and installing a quick link. I realize this option would allow for easier future removal / servicing.
I want to break the low mileage original Hyperglide chain on my Bridgestone. It still has the factory waxy type coating on it, but it is very dusty from having sat around for the better part of 3 decades.
I want to remove the chain to do a thorough deep cleaning, probably a wax lube, then reinstall the chain.
One of the pins is noticeably different from the others, see pic. I am presuming this is the original connector pin, and I'd like to maintain as much originality on the bike as possible. If I drive this pin out, can I reinstall it?
Or would I be better off picking a different spot on the chain to remove a pin/link and installing a quick link. I realize this option would allow for easier future removal / servicing.
#2
Full Member
Join Date: Aug 2014
Location: ETX/ SNH
Posts: 225
Bikes: 2011 Handsome/ Twin Six Speedy Devil, 2006 Soma Groove, 1991 Haro Impulse Comp, 1987 KHS Montana Pro, 1986 Ross Mount Hood, 1986 Mongoose ATB, 1985 Shogun Prairie Breaker I, 1973 World Voyageur, 1941 Schwinn DX "Klunker"
Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 83 Post(s)
Liked 96 Times
in
45 Posts
7 speed, Hyperglide cassette rear hub.
I want to break the low mileage original Hyperglide chain on my Bridgestone. It still has the factory waxy type coating on it, but it is very dusty from having sat around for the better part of 3 decades.
I want to remove the chain to do a thorough deep cleaning, probably a wax lube, then reinstall the chain.
One of the pins is noticeably different from the others, see pic. I am presuming this is the original connector pin, and I'd like to maintain as much originality on the bike as possible. If I drive this pin out, can I reinstall it?
Or would I be better off picking a different spot on the chain to remove a pin/link and installing a quick link. I realize this option would allow for easier future removal / servicing.
I want to break the low mileage original Hyperglide chain on my Bridgestone. It still has the factory waxy type coating on it, but it is very dusty from having sat around for the better part of 3 decades.
I want to remove the chain to do a thorough deep cleaning, probably a wax lube, then reinstall the chain.
One of the pins is noticeably different from the others, see pic. I am presuming this is the original connector pin, and I'd like to maintain as much originality on the bike as possible. If I drive this pin out, can I reinstall it?
Or would I be better off picking a different spot on the chain to remove a pin/link and installing a quick link. I realize this option would allow for easier future removal / servicing.
Edit: https://mikesbikes.com/products/hg-c...AaAmREEALw_wcB
Last edited by MrK.; 08-09-20 at 04:03 PM.
Likes For MrK.:
#3
Phyllo-buster
Join Date: Jan 2010
Location: Nova Scotia
Posts: 8,848
Bikes: roadsters, club bikes, fixed and classic
Mentioned: 133 Post(s)
Tagged: 0 Thread(s)
Quoted: 2298 Post(s)
Liked 2,056 Times
in
1,256 Posts
Although MrK. gives good advice, a chain cleaning 'in situ' is easier than swapping the stoopid Shimano special pin. I think my closeted dislike for Shimano began with those chains.
#4
Senior Member
Join Date: Jan 2015
Location: Los Angeles
Posts: 4,710
Bikes: 82 Medici, 2011 Richard Sachs, 2011 Milwaukee Road
Mentioned: 55 Post(s)
Tagged: 0 Thread(s)
Quoted: 1954 Post(s)
Liked 2,018 Times
in
1,114 Posts
Your LBS might have some pins. I use the HG 7/8, 9, and 10 use different pins and like MRk says, leave that pin in the photo alone. Story is that the holes hold that pin just fine but if you drive a replacement into that slot, it may not hold very well.
__________________
I don't do: disks, tubeless, e-shifting, or bead head nymphs.
I don't do: disks, tubeless, e-shifting, or bead head nymphs.
#6
Senior Member
Join Date: Oct 2011
Location: Fairplay Co
Posts: 9,536
Bikes: Current 79 Nishiki Custum Sport, Jeunet 620, notable previous bikes P.K. Ripper loop tail, Kawahara Laser Lite, Paramount Track full chrome, Raliegh Internatioanl, Motobecan Super Mirage. 59 Crown royak 3 speed
Mentioned: 26 Post(s)
Tagged: 1 Thread(s)
Quoted: 794 Post(s)
Liked 1,795 Times
in
640 Posts
I would just pop the HG pin and that link and replace it with a KMC 7/8 master link have done this on several bikes no issues.
Likes For zukahn1:
#7
Senior Member
Join Date: Oct 2011
Location: Fairplay Co
Posts: 9,536
Bikes: Current 79 Nishiki Custum Sport, Jeunet 620, notable previous bikes P.K. Ripper loop tail, Kawahara Laser Lite, Paramount Track full chrome, Raliegh Internatioanl, Motobecan Super Mirage. 59 Crown royak 3 speed
Mentioned: 26 Post(s)
Tagged: 1 Thread(s)
Quoted: 794 Post(s)
Liked 1,795 Times
in
640 Posts
Also I would advise against much chain cleaning beyond whip down if the chain as vintage and good as described heavy cleaning will take off the HG finish on the chain and likely make it worse.
#8
Senior Member
The early Shimano UG and HG chain tools had a shallow recesses on the opposing face of the tool. This allowed you to put the chain back together without squishing the bowed out plates. These chains could potentially 'break' if joined back together with a standard VAR or Cyclo etc chain tool. I'd imagine there's still a modern equivalent for those that want to use those stupid special pins, or for really old chains with no special pin.
I don't think it's relevant if you're just splitting the chain and using a quick link.
I don't think it's relevant if you're just splitting the chain and using a quick link.