Connector piece for forks without extra hole at drops?
#1
Newbie
Thread Starter
Join Date: Jul 2011
Posts: 32
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Connector piece for forks without extra hole at drops?
Hi, I just bought a pair of mudguards for a racer and I've realised I wont be able to install them (properly) on my bike because there are no holes on the drops, where I am supposed to attach the bracket (? sorry I'm not so sure about the names for all this stuff). My question is: are there connection pieces which I could buy to make this possible and if so what are they called?
The photo will explain it better than me
The photo will explain it better than me
#3
Banned
0 parts.. put the QR skewer through the strut holes (also for 5mm bolts)
then through the axle, with the wheel in the dropouts.
then through the axle, with the wheel in the dropouts.
#4
Senior Member
Join Date: Nov 2014
Location: Eugene, Oregon, USA
Posts: 27,547
Mentioned: 217 Post(s)
Tagged: 0 Thread(s)
Quoted: 18372 Post(s)
Liked 4,507 Times
in
3,350 Posts
Most good hardware stores or nut&bolt stores should sell "P-Clips".
There are also fenders that mount with rubber bands that are designed for road bikes. But, they always seem to move around just a bit.
There are also fenders that mount with rubber bands that are designed for road bikes. But, they always seem to move around just a bit.
#5
Senior Member
Join Date: Feb 2012
Location: Rochester, NY
Posts: 18,071
Bikes: Stewart S&S coupled sport tourer, Stewart Sunday light, Stewart Commuting, Stewart Touring, Co Motion Tandem, Stewart 3-Spd, Stewart Track, Fuji Finest, Mongoose Tomac ATB, GT Bravado ATB, JCP Folder, Stewart 650B ATB
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4199 Post(s)
Liked 3,851 Times
in
2,301 Posts
This! No involvement with the wheel's attachment means easy to deal with wheel removal with no fender issues to mess with. Andy (who likes one bolt doing only one job)
__________________
AndrewRStewart
AndrewRStewart
#6
Bad example
Join Date: Nov 2015
Location: Seattle and Reims
Posts: 3,062
Bikes: Peugeot: AO-8 1973, PA-10 1971, PR-10 1973, Sante 1988; Masi Gran Criterium 1975, Stevenson Tourer 1980, Stevenson Criterium 1981, Schwinn Paramount 1972, Rodriguez 2006, Gitane Federal ~1975, Holdsworth Pro, Follis 172 ~1973, Bianchi '62
Mentioned: 36 Post(s)
Tagged: 0 Thread(s)
Quoted: 823 Post(s)
Liked 206 Times
in
94 Posts
I also use P-clips when there are no fender eyelets. Works fine.
__________________
Keeping Seattle’s bike shops in business since 1978
Keeping Seattle’s bike shops in business since 1978
#7
Senior Member
Join Date: Aug 2005
Location: Pittsburgh, PA
Posts: 33,656
Bikes: '96 Litespeed Catalyst, '05 Litespeed Firenze, '06 Litespeed Tuscany, '20 Surly Midnight Special, All are 3x10. It is hilly around here!
Mentioned: 39 Post(s)
Tagged: 0 Thread(s)
Quoted: 2026 Post(s)
Likes: 0
Liked 1,096 Times
in
742 Posts
I think Bob's suggestion will work but will make wheel removal much more difficult and will eliminate the "qr" feature as the skewer would have to be removed completely. The P-clips are a better method.
#10
I am potato.
Join Date: Jun 2015
Location: Pacific Northwest
Posts: 3,116
Bikes: Only precision built, custom high performance elitist machines of the highest caliber. 🍆
Mentioned: 29 Post(s)
Tagged: 0 Thread(s)
Quoted: 1789 Post(s)
Liked 1,629 Times
in
933 Posts
The only problem I can think of is mud/grit getting in between the clamp and the bike. A piece of tape or something would mitigate any potential abrasion issue.
#11
Bad example
Join Date: Nov 2015
Location: Seattle and Reims
Posts: 3,062
Bikes: Peugeot: AO-8 1973, PA-10 1971, PR-10 1973, Sante 1988; Masi Gran Criterium 1975, Stevenson Tourer 1980, Stevenson Criterium 1981, Schwinn Paramount 1972, Rodriguez 2006, Gitane Federal ~1975, Holdsworth Pro, Follis 172 ~1973, Bianchi '62
Mentioned: 36 Post(s)
Tagged: 0 Thread(s)
Quoted: 823 Post(s)
Liked 206 Times
in
94 Posts
No need. The p-clips are covered in rubber. They do not move when tight, and don’t need anything else to protect the frame.
__________________
Keeping Seattle’s bike shops in business since 1978
Keeping Seattle’s bike shops in business since 1978
#12
Senior Member
Join Date: Nov 2014
Location: Eugene, Oregon, USA
Posts: 27,547
Mentioned: 217 Post(s)
Tagged: 0 Thread(s)
Quoted: 18372 Post(s)
Liked 4,507 Times
in
3,350 Posts
For those more ambitious people, there are these too:
https://www.cycle-frames.com/bicycle...TTLE-BOSS.html
https://www.cycle-frames.com/bicycle...e-for-MTB.html
https://www.cycle-frames.com/bicycle...Randoneur.html
Of course, if you are really ambitious:
https://framebuildersupply.com/produ...le-two-eyelets
https://www.cycle-frames.com/bicycle...TTLE-BOSS.html
https://www.cycle-frames.com/bicycle...e-for-MTB.html
https://www.cycle-frames.com/bicycle...Randoneur.html
Of course, if you are really ambitious:
https://framebuildersupply.com/produ...le-two-eyelets
#13
Senior Member
Join Date: Nov 2014
Location: Eugene, Oregon, USA
Posts: 27,547
Mentioned: 217 Post(s)
Tagged: 0 Thread(s)
Quoted: 18372 Post(s)
Liked 4,507 Times
in
3,350 Posts
I was imagining dropping the P-Clip attachments right down to the dropout which might help hold them into place, but that would surely leave gaps, and a potential for grime.
The rubber will help a bit with flex and anti-slip.
#14
Old fart
Join Date: Nov 2004
Location: Appleton WI
Posts: 24,784
Bikes: Several, mostly not name brands.
Mentioned: 153 Post(s)
Tagged: 0 Thread(s)
Quoted: 3587 Post(s)
Liked 3,400 Times
in
1,934 Posts
You can also get plastic P-clips. They don't corrode when exposed to salt. They're not as strong as plastic-coated metal, but plenty strong for mudguards. If you intend to mount a rack, you'll want the metal ones.
#15
Senior Member
Join Date: Sep 2014
Posts: 3,893
Mentioned: 20 Post(s)
Tagged: 0 Thread(s)
Quoted: 1062 Post(s)
Liked 665 Times
in
421 Posts
This is just one size, the same site has other sizes, and I've found these at their brick and mortar stores. I usually snug things up by shimming with innertube rubber if needed.
https://www.acehardware.com/departments/lighting-and-electrical/cable-management-cable-ties-and-electrical-tape/cable-clamps/3471125
https://www.acehardware.com/departments/lighting-and-electrical/cable-management-cable-ties-and-electrical-tape/cable-clamps/3470911
https://www.acehardware.com/departments/lighting-and-electrical/cable-management-cable-ties-and-electrical-tape/cable-clamps/3471125
https://www.acehardware.com/departments/lighting-and-electrical/cable-management-cable-ties-and-electrical-tape/cable-clamps/3470911
#16
Senior Member
Join Date: Sep 2010
Location: Roswell, GA
Posts: 8,319
Bikes: '93 Trek 750, '92 Schwinn Crisscross, '93 Mongoose Alta
Mentioned: 30 Post(s)
Tagged: 0 Thread(s)
Quoted: 1438 Post(s)
Liked 1,092 Times
in
723 Posts
Also known as Adel clamps, they are used to support fuel lines in aircraft engine compartments so abrasion of the underlying material is a non-issue if installed intelligently.