Wheel Warp?
#1
Senior Member
Thread Starter
Join Date: Aug 2005
Location: New York
Posts: 269
Bikes: 2001 LeMond Zurich, 1990 Peugeot Bordeaux/105, 1986 Cannondale, 1972 Peugeot UO8... oh, I've lost count.
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 8 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Wheel Warp?
So I've a Rolf Vector wheel that came with my 2001 LeMond Zurich. These wheels were actually made under license by Trek, and Rolf has pretty much disowned them.
Anyway, a couple of years ago, the spokes on the rear wheel drive side started getting tighter and tighter - I didn't really notice until they actually broke the hub flange! Pretty weird, but I found another set on eBay for low $ and that was that. And over the past years since, it's happened the the second wheel! The flange hasn't broken yet, but I fear it's inevitable at this point.
So has anyone ever experienced anything like this? Has anyone ever heard of anything like this? I'm big for a bicyclist, but not that big (190-200 lbs), and while the wheels are old, it just seems weird that they would both fail in this way. And the front ones are fine - no change to the spoke tension on either one.
Thoughts? Advise? Help?
Anyway, a couple of years ago, the spokes on the rear wheel drive side started getting tighter and tighter - I didn't really notice until they actually broke the hub flange! Pretty weird, but I found another set on eBay for low $ and that was that. And over the past years since, it's happened the the second wheel! The flange hasn't broken yet, but I fear it's inevitable at this point.
So has anyone ever experienced anything like this? Has anyone ever heard of anything like this? I'm big for a bicyclist, but not that big (190-200 lbs), and while the wheels are old, it just seems weird that they would both fail in this way. And the front ones are fine - no change to the spoke tension on either one.
Thoughts? Advise? Help?
#2
Senior Member
Join Date: Mar 2008
Posts: 8,688
Mentioned: 46 Post(s)
Tagged: 0 Thread(s)
Quoted: 1074 Post(s)
Liked 295 Times
in
222 Posts
So I've a Rolf Vector wheel that came with my 2001 LeMond Zurich. These wheels were actually made under license by Trek, and Rolf has pretty much disowned them.
Anyway, a couple of years ago, the spokes on the rear wheel drive side started getting tighter and tighter - I didn't really notice until they actually broke the hub flange! Pretty weird, but I found another set on eBay for low $ and that was that. And over the past years since, it's happened the the second wheel! The flange hasn't broken yet, but I fear it's inevitable at this point.
Anyway, a couple of years ago, the spokes on the rear wheel drive side started getting tighter and tighter - I didn't really notice until they actually broke the hub flange! Pretty weird, but I found another set on eBay for low $ and that was that. And over the past years since, it's happened the the second wheel! The flange hasn't broken yet, but I fear it's inevitable at this point.
WRT spokes going tighter, that CAN’T happen - unless you look to paranormal explanations.
NDS spokes slackening, that CAN happen.
#3
Really Old Senior Member
What were the measured tensions before & after?
Spokes don't get tighter unless someone took a spoke wrench to them.
Are you assuming they got tighter because you broke a flange?
Spokes don't get tighter unless someone took a spoke wrench to them.
Are you assuming they got tighter because you broke a flange?
#4
Senior Member
Thread Starter
Join Date: Aug 2005
Location: New York
Posts: 269
Bikes: 2001 LeMond Zurich, 1990 Peugeot Bordeaux/105, 1986 Cannondale, 1972 Peugeot UO8... oh, I've lost count.
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 8 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
So the rim seems to be warping to the non-drive side, while (oddly enough) staying pretty straight and true.
#5
Senior Member
Join Date: Feb 2012
Location: Rochester, NY
Posts: 18,089
Bikes: Stewart S&S coupled sport tourer, Stewart Sunday light, Stewart Commuting, Stewart Touring, Co Motion Tandem, Stewart 3-Spd, Stewart Track, Fuji Finest, Mongoose Tomac ATB, GT Bravado ATB, JCP Folder, Stewart 650B ATB
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4206 Post(s)
Liked 3,870 Times
in
2,314 Posts
Maybe the OP has discovered the "cold fusion" of the bike world. How to add energy into a system without doing anything.
My first thought was like Bill's. How were the spoke tensions measured before and after. Andy
My first thought was like Bill's. How were the spoke tensions measured before and after. Andy
__________________
AndrewRStewart
AndrewRStewart
#6
Senior Member
It's a stretch, but if the nipples were alloy and were oxidizing, it's remotely possible that the oxidation (which has larger volume than the aluminum from which it formed) pulled the spokes a little tighter. This oxidation could also happen to an alloy rim bed. But I've never heard of that happening, or observed it. It seems way more likely that the hub flange just broke. I can't dream up another situation where spokes would spontaneously tighten.
#7
Senior Member
Join Date: Feb 2012
Location: Rochester, NY
Posts: 18,089
Bikes: Stewart S&S coupled sport tourer, Stewart Sunday light, Stewart Commuting, Stewart Touring, Co Motion Tandem, Stewart 3-Spd, Stewart Track, Fuji Finest, Mongoose Tomac ATB, GT Bravado ATB, JCP Folder, Stewart 650B ATB
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4206 Post(s)
Liked 3,870 Times
in
2,314 Posts
Well... that's what my LBS said too until he saw the wheel. Hand to god, The spokes have, over time, gotten increasingly tight on the drive side, and pretty loose on the non-drive side. No one has touched them. When I got the replacement wheel last year or the year before the spokes on both sides were pretty even, tension-wise.
So the rim seems to be warping to the non-drive side, while (oddly enough) staying pretty straight and true.
So the rim seems to be warping to the non-drive side, while (oddly enough) staying pretty straight and true.
Now how tension is measured is variable. If a tension meter isn't applied the same way on each spoke then it's reading can vary. Add to that a spoke that is bladed and another layer of potential measured tension exists. Andy
__________________
AndrewRStewart
AndrewRStewart
#8
- Soli Deo Gloria -
Join Date: Aug 2015
Location: Northwest Georgia
Posts: 14,779
Bikes: 2018 Rodriguez Custom Fixed Gear, 2017 Niner RLT 9 RDO, 2015 Bianchi Pista, 2002 Fuji Robaix
Mentioned: 235 Post(s)
Tagged: 0 Thread(s)
Quoted: 6844 Post(s)
Liked 736 Times
in
469 Posts
No one should be surprised when it happens. On the contrary, if you buy a Trek/Bontrager wheel, you should expect it to fail.
The internet is full of stories going back 15 years.
Keith Bontrager blogged that it was the riders fault for not rinsing off road salt after the ride. I remember there was a guy on a forum from Honolulu who was furious.
-Tim-
#9
Senior Member
Thread Starter
Join Date: Aug 2005
Location: New York
Posts: 269
Bikes: 2001 LeMond Zurich, 1990 Peugeot Bordeaux/105, 1986 Cannondale, 1972 Peugeot UO8... oh, I've lost count.
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 8 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
FYI to all - spoke tension was "measured" by hand - pinching the spokes. It's not super accurate, but gives a general baseline. Especially since, as I mentioned, they were all pretty consistently tensioned when I got them. Now spokes on the non-drive side are pretty loose, spoke son the drive side are super tight - they really don't give at all.
#10
Senior Member
Thread Starter
Join Date: Aug 2005
Location: New York
Posts: 269
Bikes: 2001 LeMond Zurich, 1990 Peugeot Bordeaux/105, 1986 Cannondale, 1972 Peugeot UO8... oh, I've lost count.
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 8 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Trek/Bontrager wheels failing is nothing new.
No one should be surprised when it happens. On the contrary, if you buy a Trek/Bontrager wheel, you should expect it to fail.
The internet is full of stories going back 15 years.
Keith Bontrager blogged that it was the riders fault for not rinsing off road salt after the ride. I remember there was a guy on a forum from Honolulu who was furious.
-Tim-
No one should be surprised when it happens. On the contrary, if you buy a Trek/Bontrager wheel, you should expect it to fail.
The internet is full of stories going back 15 years.
Keith Bontrager blogged that it was the riders fault for not rinsing off road salt after the ride. I remember there was a guy on a forum from Honolulu who was furious.
-Tim-
Sigh, now I'm sad. Didn't want to have to replace the wheels - they're pretty.
PPS - Never had any salt on them - road or otherwise. ;-)
#11
Senior Member
Join Date: Feb 2012
Location: Rochester, NY
Posts: 18,089
Bikes: Stewart S&S coupled sport tourer, Stewart Sunday light, Stewart Commuting, Stewart Touring, Co Motion Tandem, Stewart 3-Spd, Stewart Track, Fuji Finest, Mongoose Tomac ATB, GT Bravado ATB, JCP Folder, Stewart 650B ATB
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4206 Post(s)
Liked 3,870 Times
in
2,314 Posts
And mere pinching pairs of spokes is like not using a torque wrench to tighten bolts. Sure an experienced person has a better chance of not using a proper tension tool and understanding what's really going on but even us shop wrenches don't have the best touch all the time.
Plucking spokes to hear the tone they ring at is a better non tool method but still requires the plucker to have a good sense of tone and repetition/reproduction of notes. God knows this isn't the case for all.
One issue that pro service people see all the time is the customer's perception and the timing of the moment that said perception begins. That moment is rarely when the changes to the equipment has actually begun. But all understanding of the changes, by the customer, has been baselined at the moment of their awareness began. There's a disconnect that most are not aware of or even willing to accept. Andy
Plucking spokes to hear the tone they ring at is a better non tool method but still requires the plucker to have a good sense of tone and repetition/reproduction of notes. God knows this isn't the case for all.
One issue that pro service people see all the time is the customer's perception and the timing of the moment that said perception begins. That moment is rarely when the changes to the equipment has actually begun. But all understanding of the changes, by the customer, has been baselined at the moment of their awareness began. There's a disconnect that most are not aware of or even willing to accept. Andy
__________________
AndrewRStewart
AndrewRStewart
#12
Super Moderator
Join Date: Jul 2004
Location: Ffld Cnty Connecticut
Posts: 21,843
Bikes: Old Steelies I made, Old Cannondales
Mentioned: 12 Post(s)
Tagged: 0 Thread(s)
Quoted: 1173 Post(s)
Liked 927 Times
in
612 Posts
Ride them. Check the flanges regularly for cracks.
Have an EXPERIENCED mechanic take a look at spoke tension and give you an opinion on the wheels
__________________
Bikes: Old steel race bikes, old Cannondale race bikes, less old Cannondale race bike, crappy old mtn bike.
FYI: https://www.bikeforums.net/forum-sugg...ad-please.html
Bikes: Old steel race bikes, old Cannondale race bikes, less old Cannondale race bike, crappy old mtn bike.
FYI: https://www.bikeforums.net/forum-sugg...ad-please.html
#13
Senior Member
Thread Starter
Join Date: Aug 2005
Location: New York
Posts: 269
Bikes: 2001 LeMond Zurich, 1990 Peugeot Bordeaux/105, 1986 Cannondale, 1972 Peugeot UO8... oh, I've lost count.
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 8 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
So anybody got any recommendations for replacement wheels that would look nice on that bike and DON'T cost $1,000?
#14
Senior Member
Join Date: Jul 2006
Posts: 3,065
Mentioned: 63 Post(s)
Tagged: 0 Thread(s)
Quoted: 1217 Post(s)
Liked 187 Times
in
118 Posts
FYI to all - spoke tension was "measured" by hand - pinching the spokes. It's not super accurate, but gives a general baseline. Especially since, as I mentioned, they were all pretty consistently tensioned when I got them. Now spokes on the non-drive side are pretty loose, spoke son the drive side are super tight - they really don't give at all.
#15
Senior Member
Join Date: Oct 2017
Location: Chapel Hill NC
Posts: 1,683
Bikes: 2000 Litespeed Vortex Chorus 10, 1995 DeBernardi Cromor S/S
Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 645 Post(s)
Liked 797 Times
in
446 Posts
FYI to all - spoke tension was "measured" by hand - pinching the spokes. It's not super accurate, but gives a general baseline. Especially since, as I mentioned, they were all pretty consistently tensioned when I got them. Now spokes on the non-drive side are pretty loose, spoke son the drive side are super tight - they really don't give at all.
FWIW, my dailies are a pair of Rolf Vector Pros (the Rolf-disowned Trek products) that I've used full-time for >15 years. I'm ~180 lb, and these wheels have been, and remain, completely solid. Apart from replacing the front bearings years ago, they have required nothing.
#16
Senior Member
Thread Starter
Join Date: Aug 2005
Location: New York
Posts: 269
Bikes: 2001 LeMond Zurich, 1990 Peugeot Bordeaux/105, 1986 Cannondale, 1972 Peugeot UO8... oh, I've lost count.
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 8 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Saying that "it can't happen" and implying that it isn't happening because I didn't measure the spoke tension isn't actually helpful.
The only respondant who who doesn't seem to have missed the point was TimothyH who laid some hard truth and info that i didn't know: Trek wheels of that era are garbage and should be expected to replaced.
I didn't build these wheels. I haven't touched them at all other than cleaning. They came with the bike (which I'm fond of).
#17
Senior Member
Join Date: Oct 2017
Location: Chapel Hill NC
Posts: 1,683
Bikes: 2000 Litespeed Vortex Chorus 10, 1995 DeBernardi Cromor S/S
Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 645 Post(s)
Liked 797 Times
in
446 Posts
Discussing spoke tension is hardly going off on a tangent when your original post stated "Anyway, a couple of years ago, the spokes on the rear wheel drive side started getting tighter and tighter". TimothyH may be the only respondent to didn't express skepticism that your spokes were mysteriously tightening themselves to the point of breaking the DS flange without the rim moving off center. The first is nonsensical, and the second flies in the face of everyone who's ever trued a wheel. Periodic squeezing over a couple of years is no way to conclude that spokes are becoming progressively tighter. Measure them and establish an actual baseline
Last edited by Litespud; 01-23-19 at 10:52 AM.
#18
Senior Member
Join Date: Mar 2012
Location: santa barbara CA
Posts: 1,087
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 96 Post(s)
Liked 30 Times
in
21 Posts
The experienced mechanic you had look at your wheel didn't have a tension tool?? Take the wheel to a mechanic /shop that has a tensionometer, otherwise you're wasting your time.
Brian
__________________
Brian
Brian
#19
Senior Member
Thread Starter
Join Date: Aug 2005
Location: New York
Posts: 269
Bikes: 2001 LeMond Zurich, 1990 Peugeot Bordeaux/105, 1986 Cannondale, 1972 Peugeot UO8... oh, I've lost count.
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 8 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Discussing spoke tension is hardly going off on a tangent when your original post stated "Anyway, a couple of years ago, the spokes on the rear wheel drive side started getting tighter and tighter". TimothyH may be the only respondent to didn't express skepticism that your spokes were mysteriously tightening themselves to the point of breaking the DS flange without the rim moving off center. The first is nonsensical, and the second flies in the face of everyone who's ever trued a wheel. Periodic squeezing over a couple of years is no way to conclude that spokes are becoming progressively tighter. Measure them and establish an actual baseline
I'll send you the wheel and you can see for yourselves. Nonsensical it may be: but there it is. Spokes should be roughly the same tension all around not all tight on one side and all loose on the other. When I got the replacement wheel, they were not all tight on one side and all loose on the other. Now they are. And I would certainly notice if the brakes started to rub!
Matt and Errol at Mad Dog Bikes both agree - rim is straight and true, but spokes on one side are crazy tight, and that's not right.
#20
Super Moderator
Join Date: Jul 2004
Location: Ffld Cnty Connecticut
Posts: 21,843
Bikes: Old Steelies I made, Old Cannondales
Mentioned: 12 Post(s)
Tagged: 0 Thread(s)
Quoted: 1173 Post(s)
Liked 927 Times
in
612 Posts
Oi.
I'll send you the wheel and you can see for yourselves. Nonsensical it may be: but there it is. Spokes should be roughly the same tension all around not all tight on one side and all loose on the other. When I got the replacement wheel, they were not all tight on one side and all loose on the other. Now they are. And I would certainly notice if the brakes started to rub!
Matt and Errol at Mad Dog Bikes both agree - rim is straight and true, but spokes on one side are crazy tight, and that's not right.
I'll send you the wheel and you can see for yourselves. Nonsensical it may be: but there it is. Spokes should be roughly the same tension all around not all tight on one side and all loose on the other. When I got the replacement wheel, they were not all tight on one side and all loose on the other. Now they are. And I would certainly notice if the brakes started to rub!
Matt and Errol at Mad Dog Bikes both agree - rim is straight and true, but spokes on one side are crazy tight, and that's not right.
If the mechanic judges the spoke tension to be normal, then ride them, or sell them for cheap to someone, and explain you are nervous about them.
__________________
Bikes: Old steel race bikes, old Cannondale race bikes, less old Cannondale race bike, crappy old mtn bike.
FYI: https://www.bikeforums.net/forum-sugg...ad-please.html
Bikes: Old steel race bikes, old Cannondale race bikes, less old Cannondale race bike, crappy old mtn bike.
FYI: https://www.bikeforums.net/forum-sugg...ad-please.html
Last edited by Homebrew01; 01-23-19 at 11:28 AM.
#22
Super Moderator
Join Date: Jul 2004
Location: Ffld Cnty Connecticut
Posts: 21,843
Bikes: Old Steelies I made, Old Cannondales
Mentioned: 12 Post(s)
Tagged: 0 Thread(s)
Quoted: 1173 Post(s)
Liked 927 Times
in
612 Posts
There are gazillions of good wheels under $1000. Expensive wheels mainly buy you a little less weight, if that's important.
__________________
Bikes: Old steel race bikes, old Cannondale race bikes, less old Cannondale race bike, crappy old mtn bike.
FYI: https://www.bikeforums.net/forum-sugg...ad-please.html
Bikes: Old steel race bikes, old Cannondale race bikes, less old Cannondale race bike, crappy old mtn bike.
FYI: https://www.bikeforums.net/forum-sugg...ad-please.html
#23
Senior Member
Join Date: Oct 2017
Location: Chapel Hill NC
Posts: 1,683
Bikes: 2000 Litespeed Vortex Chorus 10, 1995 DeBernardi Cromor S/S
Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 645 Post(s)
Liked 797 Times
in
446 Posts
OK, well, I guess it'll have to remain one of life's mysteries. On a separate note, it's a shame that they're playing up - they're good-looking wheels, and in my experience at least, bulletproof. I imagine that one day I'm going to wear through one or other brake track, but since Rolf don't support them (and maintain that parts are not interchangeable with current Rolf Primas), I'll be faced with consigning the otherwise excellent Hugi hubs to the parts bin and seeking a replacement wheelset. Not wild about spending a grand on a pair of Campagnolos - may end up with a pair of custom wheels, but even these are likely to be ~$500 anyway
#24
Senior Member
Thread Starter
Join Date: Aug 2005
Location: New York
Posts: 269
Bikes: 2001 LeMond Zurich, 1990 Peugeot Bordeaux/105, 1986 Cannondale, 1972 Peugeot UO8... oh, I've lost count.
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 8 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
OK, well, I guess it'll have to remain one of life's mysteries. On a separate note, it's a shame that they're playing up - they're good-looking wheels, and in my experience at least, bulletproof. I imagine that one day I'm going to wear through one or other brake track, but since Rolf don't support them (and maintain that parts are not interchangeable with current Rolf Primas), I'll be faced with consigning the otherwise excellent Hugi hubs to the parts bin and seeking a replacement wheelset. Not wild about spending a grand on a pair of Campagnolos - may end up with a pair of custom wheels, but even these are likely to be ~$500 anyway
On the other hand I don't want them to fail while I'm in a hard corner. And if they're really doomed, I'd like to be out in front of it before it actually happens.
#25
Super Moderator
Join Date: Jul 2004
Location: Ffld Cnty Connecticut
Posts: 21,843
Bikes: Old Steelies I made, Old Cannondales
Mentioned: 12 Post(s)
Tagged: 0 Thread(s)
Quoted: 1173 Post(s)
Liked 927 Times
in
612 Posts
It would be interesting to accurately compare the drive side tension between the 2 rear wheels.
Perhaps the broken one was too high.
Perhaps the broken one was too high.
__________________
Bikes: Old steel race bikes, old Cannondale race bikes, less old Cannondale race bike, crappy old mtn bike.
FYI: https://www.bikeforums.net/forum-sugg...ad-please.html
Bikes: Old steel race bikes, old Cannondale race bikes, less old Cannondale race bike, crappy old mtn bike.
FYI: https://www.bikeforums.net/forum-sugg...ad-please.html