Homemade MKS pedal cone tool
#1
Senior Member
Thread Starter
Join Date: Dec 2018
Location: Southeast TX
Posts: 614
Bikes: Several
Mentioned: 10 Post(s)
Tagged: 0 Thread(s)
Quoted: 207 Post(s)
Liked 1,042 Times
in
322 Posts
Homemade MKS pedal cone tool
In doing a bit of reading before rebuilding my first set of quill pedals (MKS Sylvans), I found others had trouble keeping the cone in place while tightening the locknut. In an effort to make it a bit easier, I hatched a plan.
I bought a cheap chainring nut wrench off of Amazon and altered it to fit the grooves in the cone while still allowing access to the locknut. It worked like a charm.
I bought a cheap chainring nut wrench off of Amazon and altered it to fit the grooves in the cone while still allowing access to the locknut. It worked like a charm.
Last edited by Brad L; 07-20-20 at 12:25 AM.
Likes For Brad L:
#3
Senior Member
Join Date: Sep 2010
Location: Roswell, GA
Posts: 8,319
Bikes: '93 Trek 750, '92 Schwinn Crisscross, '93 Mongoose Alta
Mentioned: 30 Post(s)
Tagged: 0 Thread(s)
Quoted: 1438 Post(s)
Liked 1,092 Times
in
723 Posts
Awesome, I love making tools for special jobs and you did a great job with this one.
#4
Senior Member
Join Date: Aug 2005
Location: Pittsburgh, PA
Posts: 33,656
Bikes: '96 Litespeed Catalyst, '05 Litespeed Firenze, '06 Litespeed Tuscany, '20 Surly Midnight Special, All are 3x10. It is hilly around here!
Mentioned: 39 Post(s)
Tagged: 0 Thread(s)
Quoted: 2026 Post(s)
Likes: 0
Liked 1,096 Times
in
742 Posts
Great idea. I used to stick a small screwdriver blade in the cone notches to hold it in place but your tool works much better.
#5
SE Wis
Join Date: Apr 2005
Location: Milwaukee, WI
Posts: 10,511
Bikes: '68 Raleigh Sprite, '02 Raleigh C500, '84 Raleigh Gran Prix, '91 Trek 400, 2013 Novara Randonee, 1990 Trek 970
Mentioned: 40 Post(s)
Tagged: 0 Thread(s)
Quoted: 2746 Post(s)
Liked 3,390 Times
in
2,053 Posts
#6
Senior Member
Join Date: Dec 2010
Location: St Cloud Fl.
Posts: 1,945
Bikes: Only my riders left...
Mentioned: 6 Post(s)
Tagged: 0 Thread(s)
Quoted: 350 Post(s)
Liked 782 Times
in
389 Posts
I gotta go through my excess tool box...actually I just touched every tool in my shop, no excess those wrenches...back to the screwdriver method...
#7
SE Wis
Join Date: Apr 2005
Location: Milwaukee, WI
Posts: 10,511
Bikes: '68 Raleigh Sprite, '02 Raleigh C500, '84 Raleigh Gran Prix, '91 Trek 400, 2013 Novara Randonee, 1990 Trek 970
Mentioned: 40 Post(s)
Tagged: 0 Thread(s)
Quoted: 2746 Post(s)
Liked 3,390 Times
in
2,053 Posts
Now I'm going to have to go through my tool boxes and find one of the auto antenna nut spanners I have from wrenching in a dealership in the 70's.
The power antennas I'd install as upgrades came with a cheap pin spanner about the right size and easily modified. I know I have at least one stashed in a drawer somewhere.
Looked something like this.
126-0007 ANTENNA SPANNER WRENCH [126-0007] : Baum Tools Specialty Auto Tools, Specialty European Auto Tools
The power antennas I'd install as upgrades came with a cheap pin spanner about the right size and easily modified. I know I have at least one stashed in a drawer somewhere.
Looked something like this.
126-0007 ANTENNA SPANNER WRENCH [126-0007] : Baum Tools Specialty Auto Tools, Specialty European Auto Tools
#8
Senior Member
Join Date: Jul 2018
Location: Eugene, OR
Posts: 1,326
Mentioned: 64 Post(s)
Tagged: 0 Thread(s)
Quoted: 535 Post(s)
Liked 346 Times
in
196 Posts
Thank you for posting this! I have a pair of Specialized track pedals that must be made by MKS. Same cone and nut.
The left pedal was rough. When overhauling it, I didn’t have any luck with a screwdriver. Setting the tips of needle nosed pliers in the slots in the back of the cone didn’t work either. Couldn’t get the nut tight enough against the cone and still have a proper load on the bearings.
I’ll be making this tool this week!
The left pedal was rough. When overhauling it, I didn’t have any luck with a screwdriver. Setting the tips of needle nosed pliers in the slots in the back of the cone didn’t work either. Couldn’t get the nut tight enough against the cone and still have a proper load on the bearings.
I’ll be making this tool this week!