Where to find spoke clamps for reflectors?
#1
Newbie
Thread Starter
Join Date: Sep 2022
Posts: 45
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 11 Post(s)
Likes: 0
Liked 7 Times
in
5 Posts
Where to find spoke clamps for reflectors?
Hi, I have a few late 70s to mid 80s Raleigh and Motobecane road bikes that use pretty much the same white or black spoke clamp to hold the wheel reflectors on. Where do I find replacements?? Is anyone reproducing them? I see a pair on Ebay for $22. I think not. Just asking. Thanks
Last edited by geph0007; 02-09-23 at 11:12 AM.
#2
señor miembro
Join Date: Dec 2018
Location: Pac NW
Posts: 6,625
Bikes: '70s - '80s Campagnolo
Mentioned: 92 Post(s)
Tagged: 0 Thread(s)
Quoted: 3890 Post(s)
Liked 6,488 Times
in
3,211 Posts
This may or may not help, but there are a few in my trash can every time I overhaul a bike.
Likes For SurferRosa:
#3
Ride, Wrench, Swap, Race
Join Date: Jan 2010
Location: Northern California
Posts: 9,194
Bikes: Cheltenham-Pedersen racer, Boulder F/S Paris-Roubaix, Varsity racer, '52 Christophe, '62 Continental, '92 Merckx, '75 Limongi, '76 Presto, '72 Gitane SC, '71 Schwinn SS, etc.
Mentioned: 132 Post(s)
Tagged: 0 Thread(s)
Quoted: 1565 Post(s)
Liked 1,296 Times
in
866 Posts
I'm remembering these being a sort of a maybe D-shaped plastic nut with a groove for the spoke, easily fabricated(?).
Not going to be a lot of demand, but I myself do sometimes prefer to retain original reflectors if/when it is convenient to do so. Maybe someone would go to the trouble of 3D-printing a batch of them, however unlikely (though not hard to do).
More often, I install relatively modern, svelte wheel reflectors made of clear plastic (the very slender ones held on with a single plastic quarter-turn screw). The industry has sadly had to replace these with "winged" monstrosities (that are intended to bridge the span on low-spoke-count wheels).
Not going to be a lot of demand, but I myself do sometimes prefer to retain original reflectors if/when it is convenient to do so. Maybe someone would go to the trouble of 3D-printing a batch of them, however unlikely (though not hard to do).
More often, I install relatively modern, svelte wheel reflectors made of clear plastic (the very slender ones held on with a single plastic quarter-turn screw). The industry has sadly had to replace these with "winged" monstrosities (that are intended to bridge the span on low-spoke-count wheels).
#4
Senior Member
Join Date: Jun 2019
Location: Michigan USA
Posts: 887
Bikes: A bunch of old bikes.
Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
Quoted: 278 Post(s)
Liked 873 Times
in
418 Posts
geph0007 I can't help you find the clamps for your reflectors, but I can forward this.
If the cheap plastic clamp holding your spoke mounted reflector fails during a ride and the reflector slips and rotates.
You could be looking at an accident, broken spokes, or both.
If the cheap plastic clamp holding your spoke mounted reflector fails during a ride and the reflector slips and rotates.
You could be looking at an accident, broken spokes, or both.
#5
Senior Member
I use velcro wheel reflectors that I bought from Rivendell.
#6
Senior Member
Join Date: Feb 2017
Location: Concord, NC
Posts: 701
Bikes: 1984 Bianchi Tipo Corsa, 1985 Cannondale SM600 (24/26)
Mentioned: 8 Post(s)
Tagged: 0 Thread(s)
Quoted: 235 Post(s)
Liked 349 Times
in
190 Posts
Maybe try a bike co-op type place if there is one near you. The "Recyclery" near me had zillions of old wheels and miscellaneous parts.
#7
Senior Member
Join Date: Feb 2013
Location: Alta California
Posts: 14,271
Mentioned: 415 Post(s)
Tagged: 1 Thread(s)
Quoted: 3814 Post(s)
Liked 3,345 Times
in
2,182 Posts
-----
had some lying aboot har sumwharz but the cat decided to place them in its eye...last have seen of 'em
see be yeah
-----
had some lying aboot har sumwharz but the cat decided to place them in its eye...last have seen of 'em
see be yeah
-----
#8
Ride, Wrench, Swap, Race
Join Date: Jan 2010
Location: Northern California
Posts: 9,194
Bikes: Cheltenham-Pedersen racer, Boulder F/S Paris-Roubaix, Varsity racer, '52 Christophe, '62 Continental, '92 Merckx, '75 Limongi, '76 Presto, '72 Gitane SC, '71 Schwinn SS, etc.
Mentioned: 132 Post(s)
Tagged: 0 Thread(s)
Quoted: 1565 Post(s)
Liked 1,296 Times
in
866 Posts
geph0007 I can't help you find the clamps for your reflectors, but I can forward this.
If the cheap plastic clamp holding your spoke mounted reflector fails during a ride and the reflector slips and rotates.
You could be looking at an accident, broken spokes, or both.
If the cheap plastic clamp holding your spoke mounted reflector fails during a ride and the reflector slips and rotates.
You could be looking at an accident, broken spokes, or both.
Thankfully, while I've had several wheel reflectors manage to "part company" while riding, they always became brittle when contact was made with the stationary fork legs, chainstays or whatever they contacted, followed by a "snap" sort of sound.
I suspect that the reflector's designer may have tested them for any ability to stop or to damage the wheel and spokes.
The worst outcome came when I literally test-rode my 45-lb, $200, 27.5"wheel, 2016ish Mongoose Hondo mid-fat sort of bike on my post-purchase ride out of the store. The tires were nearly flat, leading me to immediately downshift (toward the spokes), whereupon the rear wheel reflector (mounted to the right side of the wheel, doh!) contacted the rear derailer roughly and luckily didn't seriously bend the flimsy mechanism. Lesson learned about riding a K-Mart bike out of the store (although I did ride the three miles home on it with about eight psi in the 2.6" tires).
I later removed the reflectors, and also replaced the horrible Chinese twist shifters, all-steel crankset and brake levers, added fork boots, suspension post, beer/lock carrier rack, 10mm solid rear axle and so on until the bike was actually somewhat good for real off-road riding adventures.
EDIT: Recalling now that I replaced nearly every part of that bike, save for the fork, headset, calipers, front derailer and wheels.
Last edited by dddd; 02-10-23 at 12:08 AM.