Help. I really screwed up
#1
Senior Member
Thread Starter
Join Date: Oct 2009
Location: upstate NY
Posts: 161
Bikes: Jamis renegade, surly big dummy, giant talon 29er
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 62 Post(s)
Likes: 0
Liked 42 Times
in
22 Posts
Help. I really screwed up
So I was moving a fear rack from one bike to another. When tightening the last bolt down the head broke. So I decided that I would use a drill and try to drill it out good or bad it what I tried. Well the drill bit broke. So I quietly put the bike in tha garage and went about my day. Hoping I can get it all out and retap the threads. It's an aluminum frame bike.
#2
Senior Member
Join Date: Dec 2019
Location: South Shore of Long Island
Posts: 2,799
Bikes: 2010 Carrera Volans, 2015 C-Dale Trail 2sl, 2017 Raleigh Rush Hour, 2017 Blue Proseccio, 1992 Giant Perigee, 80s Gitane Rallye Tandem
Mentioned: 12 Post(s)
Tagged: 0 Thread(s)
Quoted: 1088 Post(s)
Liked 1,024 Times
in
723 Posts
Is the bit broken off inside the bolt to where its in the way? If not get a reverse direction drill bit and try again. If so try to get a tiny pair of needle nose and see if you can get enough of a grip to turn the fragment counter clockwise which may unstick it. In not tapping the bit with a center punch may work it loose. can also try epoxying something to the whole of the bolt and getting it to turn.
#4
Senior Member
Thread Starter
Join Date: Oct 2009
Location: upstate NY
Posts: 161
Bikes: Jamis renegade, surly big dummy, giant talon 29er
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 62 Post(s)
Likes: 0
Liked 42 Times
in
22 Posts
I'll pop a pic up tomorrow. I just had to walk away when it happened. It's a new bike has not even been ridden yet.
Likes For Chris!:
#5
Senior Member
Join Date: Oct 2015
Posts: 15,489
Bikes: 2015 Workswell 066, 2017 Workswell 093, 2014 Dawes Sheila, 1983 Cannondale 500, 1984 Raleigh Olympian, 2007 Cannondale Rize 4, 2017 Fuji Sportif 1 LE
Mentioned: 144 Post(s)
Tagged: 0 Thread(s)
Quoted: 7652 Post(s)
Liked 3,473 Times
in
1,834 Posts
I'd be really careful about epoxying an extension .... I mean, nothing could go wrong there, right?
Best bet is to buy a quality drill bit smaller than the screw, and to drill Very slowly. The screw/bolt/whatever might be stainless and very hard. Slip off you might gouge the frame .... push too hard you could break another bit.
You shouldn't need to retap the threads---if you drill out the bolt with a bit smaller than the bolt, you should be able to pull out the old bits and re-use the hole .... but re-tapping aluminum is not that hard .... but please be careful there, too.
I am glad you walked away ... I have failed to walk away on occasion .... it is like trying to dig your way out of a hole. As it stands, you are not really out much but the cost of a drill bit.
Best bet is to buy a quality drill bit smaller than the screw, and to drill Very slowly. The screw/bolt/whatever might be stainless and very hard. Slip off you might gouge the frame .... push too hard you could break another bit.
You shouldn't need to retap the threads---if you drill out the bolt with a bit smaller than the bolt, you should be able to pull out the old bits and re-use the hole .... but re-tapping aluminum is not that hard .... but please be careful there, too.
I am glad you walked away ... I have failed to walk away on occasion .... it is like trying to dig your way out of a hole. As it stands, you are not really out much but the cost of a drill bit.
Likes For Maelochs:
#6
Senior Member
Join Date: Jul 2009
Posts: 5,949
Bikes: Colnago, Van Dessel, Factor, Cervelo, Ritchey
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 3952 Post(s)
Liked 7,297 Times
in
2,947 Posts
Find a friendly machine shop and ask them to do it. Not only will they have the right tools to remove the screw, they'll be able to set it up so the frame suffers no damage.
Likes For tomato coupe:
#7
Senior Member
Join Date: Jan 2010
Posts: 39,238
Mentioned: 211 Post(s)
Tagged: 1 Thread(s)
Quoted: 18415 Post(s)
Liked 15,542 Times
in
7,329 Posts
Just hope this doesn't spawn a "My LMS (Local Machine Shop) sucks!" thread.
Likes For indyfabz:
#8
Señor Member
Join Date: Feb 2013
Posts: 5,066
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 649 Post(s)
Liked 292 Times
in
215 Posts
Generally, drilling a bolt is only necessary to remove the head of the bolt, then a pair of pliers or vise grips can be used to unscrew the extending piece of shank.
If the shank doesn't want to unscrew easily then something else is wrong. Are you sure this was a metric (probably M5) bolt? There are imperial sizes that are close to the metric size but will not smoothly screw in or out.
If the shank doesn't want to unscrew easily then something else is wrong. Are you sure this was a metric (probably M5) bolt? There are imperial sizes that are close to the metric size but will not smoothly screw in or out.
Likes For Chris!:
#10
SE Wis
Join Date: Apr 2005
Location: Milwaukee, WI
Posts: 10,515
Bikes: '68 Raleigh Sprite, '02 Raleigh C500, '84 Raleigh Gran Prix, '91 Trek 400, 2013 Novara Randonee, 1990 Trek 970
Mentioned: 40 Post(s)
Tagged: 0 Thread(s)
Quoted: 2747 Post(s)
Liked 3,395 Times
in
2,056 Posts
Is the drill bit still in there? Drills and taps are generally hard but brittle and can usually be broken up with a punch and the pieces picked out.
#11
Senior Member
Thread Starter
Join Date: Oct 2009
Location: upstate NY
Posts: 161
Bikes: Jamis renegade, surly big dummy, giant talon 29er
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 62 Post(s)
Likes: 0
Liked 42 Times
in
22 Posts
I was able to break the bit out and what I believe is most of the bolt. I think I'll drop it at my LBS and have them tap it for me. They are great guys and reasonably priced. Glad I walked away and didnt make it worse up front. I'll post results
#12
Full Member
The easiest way to repair is to tap it out to a size bigger thread but this may cause issues when you attach things as the larger screw will necessitate making the rack hole larger. The best solution is a helicoil which is a steel threaded insert that will match the original thread. If it were me I'd insist on the helicoil method but bike shops may not have the tools.
Note you can buy a helicoil kit on amazon from $10up which includes the drill, tap and multiple helicoils.
Note you can buy a helicoil kit on amazon from $10up which includes the drill, tap and multiple helicoils.
#13
Senior Member
Join Date: Mar 2010
Posts: 1,659
Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
Quoted: 1248 Post(s)
Liked 1,323 Times
in
674 Posts
If the threads are damaged in this instance you can also use Locktite Thread Repair compound which is not too expensive. Then run the bolt all the way through the rack mount and place a lock bolt on the other end. That won't be going anywhere.
#14
Half way there
Join Date: Sep 2015
Location: North Carolina
Posts: 2,957
Bikes: Many, and the list changes frequently
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 986 Post(s)
Liked 880 Times
in
527 Posts
Those rack mount studs have through holes so you may be able to attack the screw from the back side. I'd try a conventional right-hand drill bit smaller than the threaded portion and hope that once it "catches" in the soft metal of the broken bolt it would turn it out. Use a new bit so it will "bite" well.
#15
Sunshine
Join Date: Aug 2014
Location: Des Moines, IA
Posts: 16,614
Bikes: '18 class built steel roadbike, '19 Fairlight Secan, '88 Schwinn Premis , Black Mountain Cycles Monstercross V4, '89 Novara Trionfo
Mentioned: 123 Post(s)
Tagged: 0 Thread(s)
Quoted: 10963 Post(s)
Liked 7,490 Times
in
4,189 Posts
1- what is a fear rack?
2- screw/bolt extractors are a few dollars at the hardware store. The threading is opposite, so the tool digs into the broken bolt and the broken bolt unthreads out. Just an fyi for next time.
2- screw/bolt extractors are a few dollars at the hardware store. The threading is opposite, so the tool digs into the broken bolt and the broken bolt unthreads out. Just an fyi for next time.
#16
Happy banana slug
Join Date: Sep 2015
Location: Arcata, California, U.S., North America, Earth, Saggitarius Arm, Milky Way
Posts: 3,696
Bikes: 1984 Araya MB 261, 1992 Specialized Rockhopper Sport, 1993 Hard Rock Ultra, 1994 Trek Multitrack 750, 1995 Trek Singletrack 930
Mentioned: 31 Post(s)
Tagged: 0 Thread(s)
Quoted: 1533 Post(s)
Liked 1,529 Times
in
917 Posts
Good luck Chris!
#17
Senior Member
Likes For washed up:
#20
Senior Member
Join Date: Jul 2008
Location: 25 miles northwest of Boston
Posts: 29,549
Bikes: Bottecchia Sprint, GT Timberline 29r, Marin Muirwoods 29er, Trek FX Alpha 7.0
Mentioned: 112 Post(s)
Tagged: 0 Thread(s)
Quoted: 5224 Post(s)
Liked 3,581 Times
in
2,342 Posts
one of my favorite topics!
be sure to report back!
be sure to report back!
#21
Senior Member
Thread Starter
Join Date: Oct 2009
Location: upstate NY
Posts: 161
Bikes: Jamis renegade, surly big dummy, giant talon 29er
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 62 Post(s)
Likes: 0
Liked 42 Times
in
22 Posts
Could not get it out. Good thing my local shop had this 8.99 fix.
Last edited by Chris!; 03-10-20 at 03:59 PM.
#22
Señor Member
Join Date: Feb 2013
Posts: 5,066
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 649 Post(s)
Liked 292 Times
in
215 Posts
How did that bolt break, anyhow?
Also, you should shorten and/or put an 'acorn nut' on the end of the bolt holding the bracket on, if you like the skin on the inside of your thighs intact.
Also, you should shorten and/or put an 'acorn nut' on the end of the bolt holding the bracket on, if you like the skin on the inside of your thighs intact.
#23
Señor Member
Join Date: Feb 2013
Posts: 5,066
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 649 Post(s)
Liked 292 Times
in
215 Posts
Another, less ugly solution, would be to use a single front rack stay (iff possible with your rack) and bolt it to the hole int eh brake bridge that has a plastic plug in it.
#24
Senior Member
Thread Starter
Join Date: Oct 2009
Location: upstate NY
Posts: 161
Bikes: Jamis renegade, surly big dummy, giant talon 29er
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 62 Post(s)
Likes: 0
Liked 42 Times
in
22 Posts
I live in an area that uses a lot of road salt and my assumption is that the bolt was weak from that.... anywho it actually works out fine as long as it holds. And yes I do need to cap that bot off but they didn't have anying at the shop.
#25
Senior Member
Join Date: Jun 2014
Location: Ontario, Canada
Posts: 4,624
Bikes: iele Latina, Miele Suprema, Miele Uno LS, Miele Miele Beta, MMTB, Bianchi Model Unknown, Fiori Venezia, Fiori Napoli, VeloSport Adamas AX
Mentioned: 16 Post(s)
Tagged: 0 Thread(s)
Quoted: 1324 Post(s)
Liked 927 Times
in
640 Posts
It looks like you were able to drill quite a bit of that broken bolt out. I'd try drilling the through the full length of that broken bolt and try an Easy Out or other brand broken bolt/screw extractor.
As another poster said, shorten that protruding bolt and/or add something to the end of it so it doesn't slice your inner thigh.
Cheers
As another poster said, shorten that protruding bolt and/or add something to the end of it so it doesn't slice your inner thigh.
Cheers