Building a wheel
#1
Senior Member
Thread Starter
Join Date: Aug 2011
Posts: 88
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 18 Post(s)
Liked 0 Times
in
0 Posts
Building a wheel
Years ago I bought spooked needed to build a wheel. I got them mix and match with other lengths and now o don't even remember the measurements of it.
I want to build a wheel again how can I check to see if the ones I have are adequate.
I want to build a wheel again how can I check to see if the ones I have are adequate.
#2
Senior Member
Join Date: Apr 2006
Posts: 3,653
Mentioned: 13 Post(s)
Tagged: 0 Thread(s)
Quoted: 380 Post(s)
Likes: 0
Liked 106 Times
in
80 Posts
There are spoke length programs on the net that you put in the answers to all of their questions they will give you the answer you want. What you gave here is not enough to help. Roger
#3
Senior Member
You need various measurements from the rim and hub you plan to use to calculate spoke length.UBI has never steered me wrong.
https://bikeschool.com/index.php/res...oke-calculator
https://bikeschool.com/index.php/res...oke-calculator
#4
Member
I cant post a link yet, but I built my most recent set of wheels using the 'prowheelbuilder' spoke calculator. Just Google prowheelbuilder to get their website. I liked it mainly because it has some nice schematics to help you figure out where to take the measurements on hubs and rims. Spoke length calculation pretty much matched a few others I tried with the same values.
#5
Senior Member
I cant post a link yet, but I built my most recent set of wheels using the 'prowheelbuilder' spoke calculator. Just Google prowheelbuilder to get their website. I liked it mainly because it has some nice schematics to help you figure out where to take the measurements on hubs and rims. Spoke length calculation pretty much matched a few others I tried with the same values.
#8
Senior Member
Thread Starter
Join Date: Aug 2011
Posts: 88
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 18 Post(s)
Liked 0 Times
in
0 Posts
But I just spent some good money on it when I bough it. I atleast want to know if I have them already and not wasting money buying more
#9
Generally bewildered
Join Date: Aug 2015
Location: Eastern PA, USA
Posts: 3,037
Bikes: 2014 Trek Domane 6.9, 1999 LeMond Zurich, 1978 Schwinn Superior
Mentioned: 20 Post(s)
Tagged: 0 Thread(s)
Quoted: 1152 Post(s)
Liked 341 Times
in
251 Posts
Get a metric ruler and hang spokes on it by the j-hook. You should be able to measure each one, and sort them. You'll have two (front and rear non-drive side, and rear drive side) or three (front, rear DS, and rear NDS) lengths. If they match your rim and hub for length, great. Otehrwise, put them on e-bay and buy new.
#10
Really Old Senior Member
They make spoke rulers.
https://www.parktool.com/product/spo...er-gauge-sbc-1
https://www.parktool.com/product/spo...er-gauge-sbc-1
#11
Nigel
Join Date: Mar 2011
Location: San Jose, CA
Posts: 2,991
Bikes: 1980s and 1990s steel: CyclePro, Nishiki, Schwinn, SR, Trek........
Mentioned: 12 Post(s)
Tagged: 0 Thread(s)
Quoted: 384 Post(s)
Likes: 0
Liked 6 Times
in
6 Posts
#12
Really Old Senior Member
12''=304.8mm. Remember those CM things on the side of the ruler opposite the "inches"? 1 of them is 10mm.
If you have various lengths grouped together, lay them on a table with a straight side.
Push the J bend against the edge and you can easily see the differences.
If you have various lengths grouped together, lay them on a table with a straight side.
Push the J bend against the edge and you can easily see the differences.
Thread
Thread Starter
Forum
Replies
Last Post
Trunk Monkey
Bicycle Mechanics
11
05-19-12 03:22 AM
BugsInMyTeeth
Bicycle Mechanics
14
03-01-11 10:22 PM