odd duck-1973 Ladies Paramount P61
#1
Senior Member
Thread Starter
Join Date: Aug 2007
Posts: 139
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
odd duck-1973 Ladies Paramount P61
https://cgi.ebay.com/ws/eBayISAPI.dll...m=320277137692
Hi,
I wanted to ask about this bike that I bought on ebay last week. It is a Schwinn Ladies Paramount, but is set up differently than the ones that I'm used to seeing. The seller called it a Paramount tourist-P61. I looked up the model before bidding, and found a little information showing that there was such a model sold. Anyway, I haven't received the bike yet, but wanted to share some pictures. I've only uploaded one, but the ebay link has 23 pictures, both as small jpegs, and as large ones, hosted on a different site.
My question is the same that I have for any bike- how can I lower the gearing. Usually, the bikes I have changed were nice, but not special so I didn't feel bad about putting on modern derailleurs, cranks or freewheels. In this case, I'd like to preserve the original drivetrain as much as possible.
Would it be possible to change the Campy strada crank into a triple by using a tripleizer? Could I use a larger freewheel and still have the same Campy rear derailleur? Would it help, if I said that although I would keep the 52 chainwheel, I will never actually use it so the chain could be shortened. Would this let me still keep the original front and rear derailleurs?
One other thing that I found odd was that during bidding, the bike was shown on many websites, but I couldn't find a single comment about it on any of them, neither as a "catch" nor a "numbskull". I bought it because I'm an in-between size on a men's frame. The 21" frames are a little small, the 23" are a little big. So, I get the 21" ones but have to change the stems and seatposts. This bike is a 22" so it should fit fine. My only worry is that I am not a small person and I hope the ladies frame will be ok. I won't be ridding it hard so hopefully it won't flex too much under my Athena weight.
Thanks for any comments or suggestions.
Maureen
Hi,
I wanted to ask about this bike that I bought on ebay last week. It is a Schwinn Ladies Paramount, but is set up differently than the ones that I'm used to seeing. The seller called it a Paramount tourist-P61. I looked up the model before bidding, and found a little information showing that there was such a model sold. Anyway, I haven't received the bike yet, but wanted to share some pictures. I've only uploaded one, but the ebay link has 23 pictures, both as small jpegs, and as large ones, hosted on a different site.
My question is the same that I have for any bike- how can I lower the gearing. Usually, the bikes I have changed were nice, but not special so I didn't feel bad about putting on modern derailleurs, cranks or freewheels. In this case, I'd like to preserve the original drivetrain as much as possible.
Would it be possible to change the Campy strada crank into a triple by using a tripleizer? Could I use a larger freewheel and still have the same Campy rear derailleur? Would it help, if I said that although I would keep the 52 chainwheel, I will never actually use it so the chain could be shortened. Would this let me still keep the original front and rear derailleurs?
One other thing that I found odd was that during bidding, the bike was shown on many websites, but I couldn't find a single comment about it on any of them, neither as a "catch" nor a "numbskull". I bought it because I'm an in-between size on a men's frame. The 21" frames are a little small, the 23" are a little big. So, I get the 21" ones but have to change the stems and seatposts. This bike is a 22" so it should fit fine. My only worry is that I am not a small person and I hope the ladies frame will be ok. I won't be ridding it hard so hopefully it won't flex too much under my Athena weight.
Thanks for any comments or suggestions.
Maureen
Last edited by maureenkh; 08-03-08 at 12:02 AM.
#2
Decrepit Member
Hi Maureen,
First off, congratulations on your acquisition. It appears to be in really nice shape.
The P61, as far as I know, wasn't offered as a model in the seventies. The two ladies model Paramounts offered from 1973 until 1979 were the P60 (10-speed) and P65 (15-speed - triple plateau chainring). Both of these models came with drop handlebars.
1973 P60 and P65 Ladies Paramount consumer catalog page
1973 Paramount Catalog (P60 and P65 are on pages 6 and 7).
1973 Retail Price List (P60 and P65 are near the bottom of the page).
The P61 was a ladies tourist model made in the fifties with fixed gear, freewheeling single speed, or Sturmey-Archer 3-speed hubs, equipped pretty much like your new bike with tourist handlebars and a mattress saddle. Here's a picture of one in the 1955 catalog.
My guess is that your bike is essentially a P60 equipped at the factory with the tourist handlebars and mattress saddle like the old P61 model. Schwinn was very flexible in customizing Paramounts at the factory based on customers' requests, and I think your bike may be one of these special orders.
Since the same frame was used for the P60 and P65, your bike could be changed to a period correct Campy triple. This would mean essentially changing the whole drive train from bottom bracket to crank set, both derailleurs, and to get the wider gearing, a new freewheel with the same cogs as the P65. Or, if you're not that concerned about originality, you could go with a modern compact double and 10-speed cassette. You'd have to coldset the rear triangle for 130mm spacing and relace your rims to a new 10-speed rear hub.
Because it's a ladies' frame, it won't be as stiff as a mens' frame, but unless you're racing hard that shouldn't be a problem, even with your "Athena weight"...
Hope this helps.
First off, congratulations on your acquisition. It appears to be in really nice shape.
The P61, as far as I know, wasn't offered as a model in the seventies. The two ladies model Paramounts offered from 1973 until 1979 were the P60 (10-speed) and P65 (15-speed - triple plateau chainring). Both of these models came with drop handlebars.
1973 P60 and P65 Ladies Paramount consumer catalog page
1973 Paramount Catalog (P60 and P65 are on pages 6 and 7).
1973 Retail Price List (P60 and P65 are near the bottom of the page).
The P61 was a ladies tourist model made in the fifties with fixed gear, freewheeling single speed, or Sturmey-Archer 3-speed hubs, equipped pretty much like your new bike with tourist handlebars and a mattress saddle. Here's a picture of one in the 1955 catalog.
My guess is that your bike is essentially a P60 equipped at the factory with the tourist handlebars and mattress saddle like the old P61 model. Schwinn was very flexible in customizing Paramounts at the factory based on customers' requests, and I think your bike may be one of these special orders.
Since the same frame was used for the P60 and P65, your bike could be changed to a period correct Campy triple. This would mean essentially changing the whole drive train from bottom bracket to crank set, both derailleurs, and to get the wider gearing, a new freewheel with the same cogs as the P65. Or, if you're not that concerned about originality, you could go with a modern compact double and 10-speed cassette. You'd have to coldset the rear triangle for 130mm spacing and relace your rims to a new 10-speed rear hub.
Because it's a ladies' frame, it won't be as stiff as a mens' frame, but unless you're racing hard that shouldn't be a problem, even with your "Athena weight"...
Hope this helps.
#3
Lanky Lass
Hehehehehe Maureen, I am glad I did not compete against you! Now we have two more members with Paramounts .
Yours also looks to be in beautiful shape, congratulations!
East Hill
Yours also looks to be in beautiful shape, congratulations!
East Hill
__________________
___________________________________________________
TRY EMPATHY & HAVE LOVE IN YOUR HEART, PERHAPS I'LL SEE YOU ON THE ROAD...
___________________________________________________
TRY EMPATHY & HAVE LOVE IN YOUR HEART, PERHAPS I'LL SEE YOU ON THE ROAD...
#6
Decrepit Member
Unless she cross-chains (big chainring to one of the two larger cogs) it shouldn't be a problem.
#7
Senior Member
Thread Starter
Join Date: Aug 2007
Posts: 139
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Hi Stan, Dirtdrop and East Hill
Thank you for the information and links for the 1970's P60 and P65 models. I had suspected the same thing about the bike really being a P60 with handlebar and saddle modifications. I was pretty sure that the modifications were done by Schwinn at the factory because the handlebar and stem chosen were good quality alloy by GB, the shifters are the Schwinn "Twin-stick" (an option for Paramounts at that time), and the mattress saddle is a good quality one with a real leather top instead of vinyl.
I agree with Dirtdrop, that I should probably ride it before changing anything. I have other bikes with the gearing dialed in that I can use when I want a workout. This bike will probably be my "ride down to the coffee shop in style" bike. But one change I will make almost immediately is that saddle. I think that a black Brooks B66 or B67 (depending on the seatpost) will look much better. I'll consider collecting parts for a P15/P65 drivetrain like the one on East Hill's new treasure. As for "cold setting".... ahhhhhhh -NOOOOOOO!!!. Any changes I make to this bike will be ones that are easily changed back to the original.
East Hill, thanks very much for your congrats. The funny thing is that I found this bike because I was looking to see what Paramount you had just bought. But, don't worry, we will never compete for bikes. I am 5' 7.5'' tall with a 32 inch inseam. When I realized that this one would fit me, I used Kurt's advice to you and signed up at the bid snipping service. It worked
Maureen
Thank you for the information and links for the 1970's P60 and P65 models. I had suspected the same thing about the bike really being a P60 with handlebar and saddle modifications. I was pretty sure that the modifications were done by Schwinn at the factory because the handlebar and stem chosen were good quality alloy by GB, the shifters are the Schwinn "Twin-stick" (an option for Paramounts at that time), and the mattress saddle is a good quality one with a real leather top instead of vinyl.
I agree with Dirtdrop, that I should probably ride it before changing anything. I have other bikes with the gearing dialed in that I can use when I want a workout. This bike will probably be my "ride down to the coffee shop in style" bike. But one change I will make almost immediately is that saddle. I think that a black Brooks B66 or B67 (depending on the seatpost) will look much better. I'll consider collecting parts for a P15/P65 drivetrain like the one on East Hill's new treasure. As for "cold setting".... ahhhhhhh -NOOOOOOO!!!. Any changes I make to this bike will be ones that are easily changed back to the original.
East Hill, thanks very much for your congrats. The funny thing is that I found this bike because I was looking to see what Paramount you had just bought. But, don't worry, we will never compete for bikes. I am 5' 7.5'' tall with a 32 inch inseam. When I realized that this one would fit me, I used Kurt's advice to you and signed up at the bid snipping service. It worked
Maureen
#8
Senior Member
Join Date: Sep 2007
Location: Used to be there, now I'm here.
Posts: 1,885
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
#9
Senior Member
Thread Starter
Join Date: Aug 2007
Posts: 139
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
#12
Senior Member
Thread Starter
Join Date: Aug 2007
Posts: 139
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Though, I might stick with either the B18 in antique brown or a black saddle since the bike is orange and could clash with some colors.
Maureen
Last edited by maureenkh; 08-03-08 at 01:36 PM.
#13
Chrome Freak
Join Date: Dec 2005
Location: Kuna, ID
Posts: 3,208
Bikes: 71 Chrome Paramount P13-9, 73 Opaque Blue Paramount P15, 74 Blue Mink Raleigh Pro, 91 Waterford Paramount, Holland Titanium x2
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 4 Post(s)
Likes: 0
Liked 26 Times
in
14 Posts
Maureen, welcome to the ever growing and somewhat elite group of Paramount owners! I watched that auction, not because I was needing a woman's frame Paramount, but because they are so scarce!
When you get it, some more pictures please.
When you get it, some more pictures please.
__________________
1971 Paramount P-13 Chrome
1973 Paramount P-15 Opaque Blue
1974 Raleigh Professional Blue Mink
1991 Waterford Paramount
Holland Titanium Dura Ace Group
Holland Titanium Ultegra Triple Group
1971 Paramount P-13 Chrome
1973 Paramount P-15 Opaque Blue
1974 Raleigh Professional Blue Mink
1991 Waterford Paramount
Holland Titanium Dura Ace Group
Holland Titanium Ultegra Triple Group
#14
Senior Member
Thread Starter
Join Date: Aug 2007
Posts: 139
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Maureen
#15
Senior Member
Join Date: Aug 2005
Location: Minneapolis, MN
Posts: 798
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 16 Post(s)
Likes: 0
Liked 24 Times
in
11 Posts
I believe that most of the flex will be in the vertical plane which is a good thing as long as the seat tube doesn't yield. I believe that if high strength materials are used, a so-called "ladies" frame can be superior to a mixte. Colnago, Cinelli and Grandis have all made lightweight "Ladies" frames.
Could you tell me what diameter seat post is on your bike? That will let me know what gauge tubing was used. I hope to find time to build Jane a very lightweight "Ladies" bike, and am aiming for a much lighter frame than her mixte. If I ever found out what she weighs, I think she'd have to kill me, but I think it's around 190.
#16
Decrepit Member
Maureen's 1973 P60 will have a 27.2mm seatpost. The 531 seat tubes have an O.D. of 28.6mm, with 0.9mm wall thickness at the bottom bracket and 0.6mm at the top. This yields an I.D. of 27.4mm for the seatpost. The wall thickness and roundness tolerance, and the distortion resulting from brazing the seat cluster made the 27.2mm seatpost a perfect fit.
#17
Senior Member
Thread Starter
Join Date: Aug 2007
Posts: 139
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Maureen,
I believe that most of the flex will be in the vertical plane which is a good thing as long as the seat tube doesn't yield. I believe that if high strength materials are used, a so-called "ladies" frame can be superior to a mixte. Colnago, Cinelli and Grandis have all made lightweight "Ladies" frames.
Could you tell me what diameter seat post is on your bike? That will let me know what gauge tubing was used. I hope to find time to build Jane a very lightweight "Ladies" bike, and am aiming for a much lighter frame than her mixte. If I ever found out what she weighs, I think she'd have to kill me, but I think it's around 190.
I believe that most of the flex will be in the vertical plane which is a good thing as long as the seat tube doesn't yield. I believe that if high strength materials are used, a so-called "ladies" frame can be superior to a mixte. Colnago, Cinelli and Grandis have all made lightweight "Ladies" frames.
Could you tell me what diameter seat post is on your bike? That will let me know what gauge tubing was used. I hope to find time to build Jane a very lightweight "Ladies" bike, and am aiming for a much lighter frame than her mixte. If I ever found out what she weighs, I think she'd have to kill me, but I think it's around 190.
Maureen
#18
Senior Member
Join Date: Jul 2008
Posts: 109
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
Maureen- Beautiful bike you got there! I noticed that bike on ebay as it was so clean and my favorite color! I was hoping it would find a good home intact and not be bought as a parts bike! Enjoy!!
#19
Senior Member
Thread Starter
Join Date: Aug 2007
Posts: 139
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Thank you, Xir8n. No, definately not a parts bike! I've always wanted a Paramount, and am thilled to get this one. Keep your fingers crossed that it survives UPS. I told the seller that I would be glad to pay extra to have it packed professionally, so hopefully his bikeshop does a good job packing it. I haven't gotten a tracking number email yet so I'm guessing it hasn't been shipped yet.
Maureen
Maureen
#20
Senior Member
Thread Starter
Join Date: Aug 2007
Posts: 139
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
[QUOTE=Dirtdrop;7195944]How about a B18? My wife loves hers.
By the way, Dirtdrop, I have a Fuji Mixte also, that I bought off ebay last year but haven't set up yet. How does your wife like hers? What model is it? Mine is a light, ice blue, 56 cm Fuji Gran Tourer SE 12 speed, but I don't know what year. From the components I would guess mid to late 70s.
Maureen
By the way, Dirtdrop, I have a Fuji Mixte also, that I bought off ebay last year but haven't set up yet. How does your wife like hers? What model is it? Mine is a light, ice blue, 56 cm Fuji Gran Tourer SE 12 speed, but I don't know what year. From the components I would guess mid to late 70s.
Maureen
#21
Senior Member
Join Date: Aug 2005
Location: Minneapolis, MN
Posts: 798
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 16 Post(s)
Likes: 0
Liked 24 Times
in
11 Posts
Maureen's 1973 P60 will have a 27.2mm seatpost. The 531 seat tubes have an O.D. of 28.6mm, with 0.9mm wall thickness at the bottom bracket and 0.6mm at the top. This yields an I.D. of 27.4mm for the seatpost. The wall thickness and roundness tolerance, and the distortion resulting from brazing the seat cluster made the 27.2mm seatpost a perfect fit.
BTW Chris Kvale's temperature control is so good that he often had to use 27.4 seat posts with 531 (after a slight reaming.) Sometimes he wouldn't get enough distortion to use a 27.2. Got to admit I've never had that problem.
#22
Senior Member
Thread Starter
Join Date: Aug 2007
Posts: 139
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
seat tube size
I've built enough frames to know that that is generally the case with 531. But do you know for sure that the same seat tube was used on the ladies models? Due to the added bending load I wouldn't be surprised if they used a 531 Tourist ST (27.0 seat post) or even 531 plain gauge.
BTW Chris Kvale's temperature control is so good that he often had to use 27.4 seat posts with 531 (after a slight reaming.) Sometimes he wouldn't get enough distortion to use a 27.2. Got to admit I've never had that problem.
BTW Chris Kvale's temperature control is so good that he often had to use 27.4 seat posts with 531 (after a slight reaming.) Sometimes he wouldn't get enough distortion to use a 27.2. Got to admit I've never had that problem.
Maureen
#23
www.theheadbadge.com
Join Date: Sep 2005
Location: Southern Florida
Posts: 28,513
Bikes: https://www.theheadbadge.com
Mentioned: 124 Post(s)
Tagged: 0 Thread(s)
Quoted: 2422 Post(s)
Liked 4,396 Times
in
2,093 Posts
#24
Senior Member
Join Date: Aug 2005
Location: Minneapolis, MN
Posts: 798
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 16 Post(s)
Likes: 0
Liked 24 Times
in
11 Posts
the seat tube flex issue is one of the reasons I will probably stay with a sprung saddle of one kind or another. Those springs will absorb some of the weight, especially if the bike is ridden over a bump. The lovely B18 shown a couple of posts above has a small, modified spring similar to the B72 model so it's one that I'll definately consider, or else a B66/B67. Or, who knows, for the few blocks I may be riding to that coffee shop, the existing, nice quality mattress saddle may be fine. I'll know when the bike finally arrives.
Maureen
Maureen
If I ever win the lottery I'll commission a special run of Titanium B-67s. Lots of metal there, so lots of weight to be saved.
#25
Senior Member
Join Date: Aug 2005
Location: Minneapolis, MN
Posts: 798
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 16 Post(s)
Likes: 0
Liked 24 Times
in
11 Posts
I know there wasn't a tube set called the "Tourist" in '59. But for years they made "Standard", "Heavyweight" and SL. Standard seat tubes were 21/24 Ga. single butted. Heavyweight were 19/22 Ga. Wouldn't be surprised if some marketing type suggested they rename the Heavyweight set, Tourist.
Last edited by MnHPVA Guy; 08-03-08 at 10:17 PM.