How do i remove a confort grip?
07-14-11, 04:30 PM
#1
Junior Member
Thread Starter
Join Date: Jun 2011
Posts: 20
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
How do i remove a confort grip?
How do I remove this comfort FUJI grip?
https://picasaweb.google.com/lh/phot...eat=directlink
I tried the usual, remove the end cap, pull the hell out of it while twisting.
It didn't move at all.
https://picasaweb.google.com/lh/phot...eat=directlink
I tried the usual, remove the end cap, pull the hell out of it while twisting.
It didn't move at all.
07-14-11, 04:38 PM
#2
Bianchi Goddess
Join Date: Apr 2009
Location: Shady Pines Retirement Fort Wayne, In
Posts: 27,858
Bikes: Too many to list here check my signature.
Mentioned: 192 Post(s)
Tagged: 2 Thread(s)
Quoted: 2930 Post(s)
Liked 2,926 Times
in
1,491 Posts
if the end is open, work a small screwdriver under it and spray some hairspray or rubbing alcohol under it.
__________________
“One morning you wake up, the girl is gone, the bikes are gone, all that's left behind is a pair of old tires and a tube of tubular glue, all squeezed out"
Sugar "Kane" Kowalczyk
“One morning you wake up, the girl is gone, the bikes are gone, all that's left behind is a pair of old tires and a tube of tubular glue, all squeezed out"
Sugar "Kane" Kowalczyk
07-14-11, 06:16 PM
#3
Old fart
Join Date: Nov 2004
Location: Appleton WI
Posts: 24,786
Bikes: Several, mostly not name brands.
Mentioned: 153 Post(s)
Tagged: 0 Thread(s)
Quoted: 3588 Post(s)
Liked 3,400 Times
in
1,934 Posts
Compressed air is what we used in the shop.
07-14-11, 08:03 PM
#6
Senior Member
Join Date: Oct 2009
Location: Northern/Central VA
Posts: 212
Bikes: Specialized Sirrus, Univega Activa ST Hybrid, 70's Schwinn Traveler, Giant Innova, Nishiki Mixte
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Compressed air +2
07-14-11, 10:49 PM
#7
Senior Member
The air or screwdriver and a spray bottle with soapy water to squirt in next to the screw driver.
07-15-11, 06:36 AM
#8
Member
Join Date: Jun 2011
Posts: 40
Bikes: 1995 GT Arrette
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 2 Post(s)
Liked 0 Times
in
0 Posts
07-15-11, 06:44 AM
#9
Lover of Old Chrome Moly
Join Date: May 2011
Location: NW Minnesota
Posts: 2,949
Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 143 Post(s)
Likes: 0
Liked 23 Times
in
17 Posts
I'm not familiar with this grip, but some comfort grips have a small set hex screw (Ergon grips among others have this feature) that must be loosened. Then any standard grip removal procedure will work. I discourage the use of WD40 or other non-water soluable lubes if you are planning to reuse the grips as some grip materials can absorb enough lube to make it difficult to remount them later. I use my cleaner/degreaser which is half Simple Green, half water and just a bit of Dawn dish soap.
The air compressor trick works a treat. I tried it on a 1950s vintage Schwinn because I didn't want to risk damaging the grips. It took a couple of short blasts to get the first one loose, but the second grip shot off instantly.
The air compressor trick works a treat. I tried it on a 1950s vintage Schwinn because I didn't want to risk damaging the grips. It took a couple of short blasts to get the first one loose, but the second grip shot off instantly.
07-15-11, 07:44 AM
#10
Mad bike riding scientist
Join Date: Nov 2004
Location: Denver, CO
Posts: 27,363
Bikes: Some silver ones, a red one, a black and orange one, and a few titanium ones
Mentioned: 152 Post(s)
Tagged: 1 Thread(s)
Quoted: 6219 Post(s)
Liked 4,218 Times
in
2,365 Posts
If you don't have an air compressor, the screwdriver works but the best way is to get a basting syringe and inject water through the grip. Slides right off. Use hairspray to put them back on.
__________________
Stuart Black
Plan Epsilon Around Lake Michigan in the era of Covid
Old School…When It Wasn’t Ancient bikepacking
Gold Fever Three days of dirt in Colorado
Pokin' around the Poconos A cold ride around Lake Erie
Dinosaurs in Colorado A mountain bike guide to the Purgatory Canyon dinosaur trackway
Solo Without Pie. The search for pie in the Midwest.
Picking the Scablands. Washington and Oregon, 2005. Pie and spiders on the Columbia River!
Stuart Black
Plan Epsilon Around Lake Michigan in the era of Covid
Old School…When It Wasn’t Ancient bikepacking
Gold Fever Three days of dirt in Colorado
Pokin' around the Poconos A cold ride around Lake Erie
Dinosaurs in Colorado A mountain bike guide to the Purgatory Canyon dinosaur trackway
Solo Without Pie. The search for pie in the Midwest.
Picking the Scablands. Washington and Oregon, 2005. Pie and spiders on the Columbia River!
07-15-11, 11:48 AM
#11
Junior Member
Thread Starter
Join Date: Jun 2011
Posts: 20
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
You guys are a resourceful bunch!
about the screwdriver... that would scratch the handlebars wouldn't it?
i will try to inject some soapy water under them...
...what's "hairspray" exactly? Wife has some 20 kinds around...
about the screwdriver... that would scratch the handlebars wouldn't it?
i will try to inject some soapy water under them...
...what's "hairspray" exactly? Wife has some 20 kinds around...
07-15-11, 11:59 AM
#12
cowboy, steel horse, etc
Join Date: Sep 2008
Location: The hot spot.
Posts: 44,845
Bikes: everywhere
Mentioned: 71 Post(s)
Tagged: 1 Thread(s)
Quoted: 12776 Post(s)
Liked 7,693 Times
in
4,082 Posts
Screwdrivers can scratch bars, but it's in an area that never sees the light of day. If you want to keep your bars unscathed you can use thicker bamboo skewers. The thin ones don't open up enough room to spray into and can break easier if you pry up to make room.
For grip removal, my favorite liquid in a spray bottle found in most homes is window cleaner. I keep a spray bottle of Isopropyl personally, though. It's a bit better for re-installation lube as it dries just a bit faster than window cleaner. A good clean grip put on a good clean bar with Isopropyl or Window cleaner usually stays in place quite well after a few hours dry time.
Soap and WD-40 both require thorough cleaning afterwards or your grips will never stay in place after re-install. I'd advise against using either.
Hairspray is usually best reserved for re-installing grips that twist on the bar too much. For keeping grips in place, Aqua Net Extra Super Hold is best. Some desperate MTBers have been known to resort to spray paint on installation to keep grips in place. Remember that using hairspray will make subsequent grip removal a bit more difficult. Grips slid on with spraypaint will usually have to be cut off with a razor blade.
For grip removal, my favorite liquid in a spray bottle found in most homes is window cleaner. I keep a spray bottle of Isopropyl personally, though. It's a bit better for re-installation lube as it dries just a bit faster than window cleaner. A good clean grip put on a good clean bar with Isopropyl or Window cleaner usually stays in place quite well after a few hours dry time.
Soap and WD-40 both require thorough cleaning afterwards or your grips will never stay in place after re-install. I'd advise against using either.
Hairspray is usually best reserved for re-installing grips that twist on the bar too much. For keeping grips in place, Aqua Net Extra Super Hold is best. Some desperate MTBers have been known to resort to spray paint on installation to keep grips in place. Remember that using hairspray will make subsequent grip removal a bit more difficult. Grips slid on with spraypaint will usually have to be cut off with a razor blade.
Last edited by LesterOfPuppets; 07-15-11 at 12:25 PM.
07-15-11, 12:18 PM
#13
Senior Member
Screwdrivers can scratch bars, but it's in an area that never sees the light of day. If you want to keep your bars unscathed you can use thicker bamboo skewers. The thin ones don't open up enough room to spray into and can break easier if you pry up to make room.
For grip removal, my favorite liquid in a spray bottle found in most homes is window cleaner. I keep a spray bottle of Isopropyl personally, though. It's a bit better for re-installation lube as it dries just a bit faster than window cleaner. A good clean grip put on a good clean bar with Isopropyl or Window cleaner usually stays in place quite well after a few hours dry time.
Soap and WD-40 both require thorough cleaning afterwards or your grips will never stay in place after re-install. I'd advise against using either.
Hairspray is usually best for re-installing grips that twist on the bar too much. For keeping grips in place, Aqua Net Extra Super Hold is best. Some desperate MTBers have been known to resort to spray paint on installation to keep grips in place.
For grip removal, my favorite liquid in a spray bottle found in most homes is window cleaner. I keep a spray bottle of Isopropyl personally, though. It's a bit better for re-installation lube as it dries just a bit faster than window cleaner. A good clean grip put on a good clean bar with Isopropyl or Window cleaner usually stays in place quite well after a few hours dry time.
Soap and WD-40 both require thorough cleaning afterwards or your grips will never stay in place after re-install. I'd advise against using either.
Hairspray is usually best for re-installing grips that twist on the bar too much. For keeping grips in place, Aqua Net Extra Super Hold is best. Some desperate MTBers have been known to resort to spray paint on installation to keep grips in place.
I am with you on the hairspray though. I prefer the water based spritzer type over the aerosol though.
07-15-11, 04:16 PM
#14
Lover of Old Chrome Moly
Join Date: May 2011
Location: NW Minnesota
Posts: 2,949
Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 143 Post(s)
Likes: 0
Liked 23 Times
in
17 Posts
Aquanet hairspray in the pump. Great stuff for grip installation. If you use enough on a Bouffant hairdo, you no longer need a helmet.
07-15-11, 05:08 PM
#15
Senior Member
Join Date: Jun 2007
Location: A Coffin Called Earth. or Toronto, ON
Posts: 12,257
Bikes: Bianchi, Miyata, Dahon, Rossin
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 3 Post(s)
Likes: 0
Liked 5 Times
in
5 Posts
I just spray in some fabreze.
smells way better and does dry out, unlike WD40.
smells way better and does dry out, unlike WD40.
__________________
Food for thought: if you aren't dead by 2050, you and your entire family will be within a few years from starvation. Now that is a cruel gift to leave for your offspring. ;)
https://sanfrancisco.ibtimes.com/arti...ger-photos.htm
Food for thought: if you aren't dead by 2050, you and your entire family will be within a few years from starvation. Now that is a cruel gift to leave for your offspring. ;)
https://sanfrancisco.ibtimes.com/arti...ger-photos.htm
07-18-11, 11:37 AM
#17
Map maker
Join Date: Feb 2008
Location: Richmond,VA
Posts: 728
Bikes: Ventana El Ciclon, Walt Works 29er, Specialized Enduro (fixed up for my son).
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Liked 0 Times
in
0 Posts
WD-40 is the stuff
it actually works great for grip installation as well - pry up the ends and stick the little red spray tube as far as it will go. spray and twist.
for installation: spay just a tiny bit* of WD-40 slide the grip on and leave it for a few hours the WD-40 will evaporate out and the kerosene in the spray makes the rubber grip even better.
I've used it for years and it always works.
(*If you use too much you might have to remove the grip and wipe it out and try again.)
it actually works great for grip installation as well - pry up the ends and stick the little red spray tube as far as it will go. spray and twist.
for installation: spay just a tiny bit* of WD-40 slide the grip on and leave it for a few hours the WD-40 will evaporate out and the kerosene in the spray makes the rubber grip even better.
I've used it for years and it always works.
(*If you use too much you might have to remove the grip and wipe it out and try again.)
07-18-11, 04:06 PM
#18
Junior Member
Thread Starter
Join Date: Jun 2011
Posts: 20
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Used a bamboo skewers to remove (had to lube one of them in wd-40)
to insert one went in without anything, just reused the skewers trick in reverse... one needed some lubrication, used 90proof rubbing alchool. a lot of it. then just worked the skewers to help it evaporate on all sides.
thanks for all the tips everyone!
to insert one went in without anything, just reused the skewers trick in reverse... one needed some lubrication, used 90proof rubbing alchool. a lot of it. then just worked the skewers to help it evaporate on all sides.
thanks for all the tips everyone!
07-18-11, 11:21 PM
#19
Senior Member
Join Date: May 2011
Posts: 50
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
I like the screwdriver method and silicone spray. The silicone spray does dry out although it will leave some film. Wash with soap and water before reinstalling and you're good.
Thread
Thread Starter
Forum
Replies
Last Post
wernst
Bicycle Mechanics
70
11-12-19 10:25 PM
stickmangumby
Bicycle Mechanics
6
02-18-10 03:52 PM
