Chain length choices...
#26
Senior Member
Join Date: Jan 2008
Location: Beaverton, OR
Posts: 14,742
Bikes: Yes
Mentioned: 525 Post(s)
Tagged: 0 Thread(s)
Quoted: 3230 Post(s)
Liked 3,862 Times
in
1,439 Posts
I was going through this last night with a SunTour rear derailleur setup. I put the chain on the big-big combination, threaded through the derailleur and the full chain pulled the derailleur forward a bit. Since I was using a quick-link chain, it was easy to install it like this and check the small-small. Small-small was too slack, so I went back to big-big and figure out how many links I was comfortable removing (two, in this case). Big-big still fit -- small-small was a little slacker than I'd like, but short of moving the wheel back in the drop-outs, I think this is the best I'll get.
__________________
My Bikes
My Bikes
Likes For Andy_K:
#27
Senior Member
Thread Starter
Join Date: Feb 2012
Location: Williamsburg, VA Sebastian, FL
Posts: 1,363
Bikes: 1987 Centurion Ironman Master, 1992 Koga Miyata Exerciser, 1992 Schwinn Crosscut
Mentioned: 6 Post(s)
Tagged: 0 Thread(s)
Quoted: 209 Post(s)
Likes: 0
Liked 175 Times
in
92 Posts
Chain line is good, cable is brand new, and this pic shows big-big.
I thought of the hanger being out of alignment, but visually it looks good.
Without the tool I don't know how I'd check it more exactly, or tweak it.
You guys would probably frown if I suggested a crescent wrench!
I thought of the hanger being out of alignment, but visually it looks good.
Without the tool I don't know how I'd check it more exactly, or tweak it.
You guys would probably frown if I suggested a crescent wrench!
#29
Senior Member
Join Date: Jul 2006
Location: San Jose (Willow Glen) Ca
Posts: 9,831
Bikes: Kirk Custom JK Special, '84 Team Miyata,(dura ace old school) 80?? SR Semi-Pro 600 Arabesque
Mentioned: 106 Post(s)
Tagged: 0 Thread(s)
Quoted: 2336 Post(s)
Liked 2,806 Times
in
1,533 Posts
I may be misunderstanding you, but usually one starts with big to big, not small to small. See Park Tools method for a conservative approach, or look at Sheldon Brown's method.
__________________
Life is too short not to ride the best bike you have, as much as you can
(looking for Torpado Super light frame/fork or for Raleigh International frame fork 58cm)
Life is too short not to ride the best bike you have, as much as you can
(looking for Torpado Super light frame/fork or for Raleigh International frame fork 58cm)
#32
Senior Member
Thread Starter
Join Date: Feb 2012
Location: Williamsburg, VA Sebastian, FL
Posts: 1,363
Bikes: 1987 Centurion Ironman Master, 1992 Koga Miyata Exerciser, 1992 Schwinn Crosscut
Mentioned: 6 Post(s)
Tagged: 0 Thread(s)
Quoted: 209 Post(s)
Likes: 0
Liked 175 Times
in
92 Posts
Thanks. At the risk of forumscorn I took a crescent wrench to the hanger and gave it some leverage. Not sure I gained much, if any, but thought it couldn't hurt.
The RD is now dropping down onto the 12 cog about half the time, better than before, but not right yet. When I re-assembled I double-checked my limits, and held pretty good tension on the cable, in the small cog, while tightening. It's still not jumping inward very successfully, so I'll also be working on that tomorrow.
I'm hoping it's my inexperience with brifters causing my woes, and that I'll figure it out eventually!
The RD is now dropping down onto the 12 cog about half the time, better than before, but not right yet. When I re-assembled I double-checked my limits, and held pretty good tension on the cable, in the small cog, while tightening. It's still not jumping inward very successfully, so I'll also be working on that tomorrow.
I'm hoping it's my inexperience with brifters causing my woes, and that I'll figure it out eventually!
#33
Senior Member
Chain length looks right to me. I think you're good.
You might want to play with your B screw adjustment, and see how that affects things. Usually I shoot for the RD cage to be a bit more parallel to the chainstay.
RE checking your hanger alignment without a tool, it can be done. I've always had a tool and but like I said earlier, you can do it with a rear wheel. Here's a video from RT:
I like to adjust the derailleurs without using brifters at all to start with. Yank on the cable by the downtube to shift.
You might want to play with your B screw adjustment, and see how that affects things. Usually I shoot for the RD cage to be a bit more parallel to the chainstay.
RE checking your hanger alignment without a tool, it can be done. I've always had a tool and but like I said earlier, you can do it with a rear wheel. Here's a video from RT:
I like to adjust the derailleurs without using brifters at all to start with. Yank on the cable by the downtube to shift.
Likes For Salamandrine:
#34
Senior Member
Thread Starter
Join Date: Feb 2012
Location: Williamsburg, VA Sebastian, FL
Posts: 1,363
Bikes: 1987 Centurion Ironman Master, 1992 Koga Miyata Exerciser, 1992 Schwinn Crosscut
Mentioned: 6 Post(s)
Tagged: 0 Thread(s)
Quoted: 209 Post(s)
Likes: 0
Liked 175 Times
in
92 Posts
Cool video, thanks for sharing it.
I'd be a bit nervous using a true wheel from one of my other bikes, though.
With the torque needed, I'd worry that the trueness of the levering wheel might be compromised.
I'd be a bit nervous using a true wheel from one of my other bikes, though.
With the torque needed, I'd worry that the trueness of the levering wheel might be compromised.
#35
Senior Member
I can understand your worry about tweaking a wheel, but IME wheels are pretty strong and derailleur hangers are not difficult to bend. OTOH, he used an MTB wheel for this... If you're worried about it, you could always use a wheel as a gauge only.
Likes For Salamandrine:
#36
Banned.
Buy a derailleur hanger adjustment tool, or borrow one. If you were still in DTW you could borrow mine, I'd even do it for you. It's a one beer job.
There has to be a member close to you that has one.
There has to be a member close to you that has one.
#37
Senior Member
Thread Starter
Join Date: Feb 2012
Location: Williamsburg, VA Sebastian, FL
Posts: 1,363
Bikes: 1987 Centurion Ironman Master, 1992 Koga Miyata Exerciser, 1992 Schwinn Crosscut
Mentioned: 6 Post(s)
Tagged: 0 Thread(s)
Quoted: 209 Post(s)
Likes: 0
Liked 175 Times
in
92 Posts
They probably haven't had one in a while, but I've always regretted leaving Detroit before experiencing a Slow Roll. Those were supposedly quite the weekly event!
I'll pull the rear wheel off my hybrid and check the alignment that way. It sure looks close, but that will at least let me know if it is perfect or not. I may even use the wheel to tweak it, but will be proceeding cautiously.
#38
ambulatory senior
Join Date: Dec 2016
Location: Peoria Il
Posts: 5,998
Bikes: Austro Daimler modified by Gugie! Raleigh Professional and lots of other bikes.
Mentioned: 76 Post(s)
Tagged: 0 Thread(s)
Quoted: 1954 Post(s)
Liked 3,657 Times
in
1,677 Posts
Nice. If I were still in the Motor City I'd be all over your offer!
They probably haven't had one in a while, but I've always regretted leaving Detroit before experiencing a Slow Roll. Those were supposedly quite the weekly event!
I'll pull the rear wheel off my hybrid and check the alignment that way. It sure looks close, but that will at least let me know if it is perfect or not. I may even use the wheel to tweak it, but will be proceeding cautiously.
They probably haven't had one in a while, but I've always regretted leaving Detroit before experiencing a Slow Roll. Those were supposedly quite the weekly event!
I'll pull the rear wheel off my hybrid and check the alignment that way. It sure looks close, but that will at least let me know if it is perfect or not. I may even use the wheel to tweak it, but will be proceeding cautiously.
#39
Senior Member
#40
Senior Member
Thread Starter
Join Date: Feb 2012
Location: Williamsburg, VA Sebastian, FL
Posts: 1,363
Bikes: 1987 Centurion Ironman Master, 1992 Koga Miyata Exerciser, 1992 Schwinn Crosscut
Mentioned: 6 Post(s)
Tagged: 0 Thread(s)
Quoted: 209 Post(s)
Likes: 0
Liked 175 Times
in
92 Posts
Dual-wheel method showed the hanger a bit off, which I believe I corrected.
I'll hunt around for the tool, but until then I'm ruling the hanger aligned.
But, the RD is still not dropping the chain onto the small cog, messing up all other smaller cog shifting. I even lengthened the cable housing entering the DR, to decrease friction, just in case that had any affect.
How's this for a possibility? The top jockey wheel is so close to the 12t cog that chain stiffness slows or prevents the final shift?
I'll hunt around for the tool, but until then I'm ruling the hanger aligned.
But, the RD is still not dropping the chain onto the small cog, messing up all other smaller cog shifting. I even lengthened the cable housing entering the DR, to decrease friction, just in case that had any affect.
How's this for a possibility? The top jockey wheel is so close to the 12t cog that chain stiffness slows or prevents the final shift?
Last edited by 67tony; 06-30-20 at 07:26 PM.
#41
Senior Member
To be fair, none of my shifting woes were ever caused by the length of the chain. It was always hanger alignment, RD, or cables.
#42
Senior Member
Join Date: Apr 2009
Posts: 923
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 369 Post(s)
Liked 526 Times
in
278 Posts
JMO of course but finding some Shimano instructions to read might be illuminating
#43
Senior Member
So if you completely slack the cable*, and back out the limit screw all the way, the RD still won't shift into the 12t? Ignore the brifters completely, shift by pulling the cable and letting it go.
* (let out like a half inch)
* (let out like a half inch)
#44
Senior Member
Join Date: Jun 2014
Location: Ontario, Canada
Posts: 4,624
Bikes: iele Latina, Miele Suprema, Miele Uno LS, Miele Miele Beta, MMTB, Bianchi Model Unknown, Fiori Venezia, Fiori Napoli, VeloSport Adamas AX
Mentioned: 16 Post(s)
Tagged: 0 Thread(s)
Quoted: 1324 Post(s)
Liked 927 Times
in
640 Posts
Have you got the cble secured the proper way in the derailleur cable anchor bolt?
Cheers
Cheers
#46
Senior Member
Thread Starter
Join Date: Feb 2012
Location: Williamsburg, VA Sebastian, FL
Posts: 1,363
Bikes: 1987 Centurion Ironman Master, 1992 Koga Miyata Exerciser, 1992 Schwinn Crosscut
Mentioned: 6 Post(s)
Tagged: 0 Thread(s)
Quoted: 209 Post(s)
Likes: 0
Liked 175 Times
in
92 Posts
I'm liking my diagnosis of the jockey wheel being too close to the small cog, but don't know how to widen that distance. I'm not sure the B-limit screw would alter it that much...
Last edited by 67tony; 06-30-20 at 09:29 PM.
#47
Ride, Wrench, Swap, Race
Join Date: Jan 2010
Location: Northern California
Posts: 9,180
Bikes: Cheltenham-Pedersen racer, Boulder F/S Paris-Roubaix, Varsity racer, '52 Christophe, '62 Continental, '92 Merckx, '75 Limongi, '76 Presto, '72 Gitane SC, '71 Schwinn SS, etc.
Mentioned: 132 Post(s)
Tagged: 0 Thread(s)
Quoted: 1561 Post(s)
Liked 1,284 Times
in
855 Posts
I believe that the type of derailer housing is the problem here.
This is the old, very stiff 5mm housing that prevents the rear derailer from floating about the cassette properly under it's dual-sprung movement. No bueno.
If the housing were longer it would be less of a problem, but this derailer is from the 4mm housing era and needs more flexibility there.
By the way, did you perhaps use any grease on the cable? What you want for best shifting and strong return action toward the smallest cog is some original pre-lubricated SP-41 housing, 4mm in diameter and of sufficient length for the guide pulley to track the cassette profile.
And the cable guide at the bottom bracket should be plastic, or with plastic noodle at least guiding the cable there.
The 9s-era derailers used modest return-spring tension that relied on free cable movement along the entire path of the cable.
This is the old, very stiff 5mm housing that prevents the rear derailer from floating about the cassette properly under it's dual-sprung movement. No bueno.
If the housing were longer it would be less of a problem, but this derailer is from the 4mm housing era and needs more flexibility there.
By the way, did you perhaps use any grease on the cable? What you want for best shifting and strong return action toward the smallest cog is some original pre-lubricated SP-41 housing, 4mm in diameter and of sufficient length for the guide pulley to track the cassette profile.
And the cable guide at the bottom bracket should be plastic, or with plastic noodle at least guiding the cable there.
The 9s-era derailers used modest return-spring tension that relied on free cable movement along the entire path of the cable.
#48
Senior Member
Join Date: Jun 2014
Location: Ontario, Canada
Posts: 4,624
Bikes: iele Latina, Miele Suprema, Miele Uno LS, Miele Miele Beta, MMTB, Bianchi Model Unknown, Fiori Venezia, Fiori Napoli, VeloSport Adamas AX
Mentioned: 16 Post(s)
Tagged: 0 Thread(s)
Quoted: 1324 Post(s)
Liked 927 Times
in
640 Posts
Can you post another image taken from the rear of the bike and looking towards the front? The one you posted earlier is too small to make out details.
Cheers
Cheers
#49
Senior Member
The B screw shouldn't need to be super optimized just for the RD to drop the chain into the smallest cog. Assuming the hanger is now close enough to aligned, that really only leaves friction issues. This could be isolated by disconnecting the RD from the cable completely. Shift it into the 13 by moving the parallelogram with manually, ie with your hand, and then let it go. If it drops right into the 12, then you have a hang up along your cable somewhere. If it still won't drop in, there's not much left except a still bent hanger, stiff pivots, or a weak spring in the derailleur. Maybe a tweaked jockey cage. I'd make sure your cable is moving smoothly first.
Personally I advocate plenty of grease. No cable has not moved because it had too much grease. However, if you are using high tech prelubed cables, along with the correct matching housing, you don't need too. OT but this was a big religious debate when lined housing first came out.
Also make sure any linings are properly opened up with an awl, and housing ends are ground smooth.
Personally I advocate plenty of grease. No cable has not moved because it had too much grease. However, if you are using high tech prelubed cables, along with the correct matching housing, you don't need too. OT but this was a big religious debate when lined housing first came out.
Also make sure any linings are properly opened up with an awl, and housing ends are ground smooth.
#50
Senior Member
Thread Starter
Join Date: Feb 2012
Location: Williamsburg, VA Sebastian, FL
Posts: 1,363
Bikes: 1987 Centurion Ironman Master, 1992 Koga Miyata Exerciser, 1992 Schwinn Crosscut
Mentioned: 6 Post(s)
Tagged: 0 Thread(s)
Quoted: 209 Post(s)
Likes: 0
Liked 175 Times
in
92 Posts
I believe that the type of derailer housing is the problem here.
This is the old, very stiff 5mm housing that prevents the rear derailer from floating about the cassette properly under it's dual-sprung movement. No bueno.
If the housing were longer it would be less of a problem, but this derailer is from the 4mm housing era and needs more flexibility there.
By the way, did you perhaps use any grease on the cable? What you want for best shifting and strong return action toward the smallest cog is some original pre-lubricated SP-41 housing, 4mm in diameter and of sufficient length for the guide pulley to track the cassette profile.
And the cable guide at the bottom bracket should be plastic, or with plastic noodle at least guiding the cable there.
This is the old, very stiff 5mm housing that prevents the rear derailer from floating about the cassette properly under it's dual-sprung movement. No bueno.
If the housing were longer it would be less of a problem, but this derailer is from the 4mm housing era and needs more flexibility there.
By the way, did you perhaps use any grease on the cable? What you want for best shifting and strong return action toward the smallest cog is some original pre-lubricated SP-41 housing, 4mm in diameter and of sufficient length for the guide pulley to track the cassette profile.
And the cable guide at the bottom bracket should be plastic, or with plastic noodle at least guiding the cable there.
Although the cable is greased, the housing is definitely old, and stiff.
(The cable guide on the BB is plastic, and I even have that lightly greased as well.)