Reusing H+Son TB14 rims - how worn is too worn?
#1
Senior Member
Thread Starter
Join Date: Jun 2009
Location: Brooklyn, NY
Posts: 512
Bikes: 1970s Coppi/Fiorelli beater, 1973 Raleigh Competition, 1972 Bob Jackson, 1970 Cilo Sprint-X, 1985 Fuji Touring Series IV, 1969 Legnano Roma
Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 217 Post(s)
Liked 198 Times
in
129 Posts
Reusing H+Son TB14 rims - how worn is too worn?
Picked up some black TB14 rims today, mainly because they were going cheap enough for me to act impulsively.
They seem ok, from what I can determine - turns out it's trickier to tell when you dont have a hub to spin them around! they seem flat and round and show no real signs of abuse. But the brake surfaces have seen some miles - they look like any other well-worn braking surface, but with a "concaveness" that you can definitely feel with a fingertip even if you can't really see it.
Part of the appeal is that TB14s could be an easy swap for MA40s on a wheelset where the rims are tatty but everything else is good - ideally, this could be as simple as the swap RiddleOfSteel showed us a year ago. I'm not looking for miracles, just a decent (wider) set of rims that could handle at least another 2000-3000 miles of easy touring
So my concern/question is - does a concave brake surface mean these are too far gone to invest that kind of effort? should i save my pennies for a new set, 'cos they're awesome, or are TB14s engineered so beefily that I should just press on regardless with these survivors?
They seem ok, from what I can determine - turns out it's trickier to tell when you dont have a hub to spin them around! they seem flat and round and show no real signs of abuse. But the brake surfaces have seen some miles - they look like any other well-worn braking surface, but with a "concaveness" that you can definitely feel with a fingertip even if you can't really see it.
Part of the appeal is that TB14s could be an easy swap for MA40s on a wheelset where the rims are tatty but everything else is good - ideally, this could be as simple as the swap RiddleOfSteel showed us a year ago. I'm not looking for miracles, just a decent (wider) set of rims that could handle at least another 2000-3000 miles of easy touring
So my concern/question is - does a concave brake surface mean these are too far gone to invest that kind of effort? should i save my pennies for a new set, 'cos they're awesome, or are TB14s engineered so beefily that I should just press on regardless with these survivors?
#2
Senior Member
Join Date: Jun 2006
Posts: 20,305
Mentioned: 130 Post(s)
Tagged: 0 Thread(s)
Quoted: 3464 Post(s)
Liked 2,828 Times
in
1,995 Posts
measure, they way you need to do it is with a micrometer, you have to get around the thicker portion.
I do not know the start dimension of the rims, should be reference-able.
I do not think the rims are especially light or heavy. I want to recall 450grams ? for a box section rim, not bad.
I do not know the start dimension of the rims, should be reference-able.
I do not think the rims are especially light or heavy. I want to recall 450grams ? for a box section rim, not bad.
#3
2k miles from the midwest
Join Date: Feb 2005
Location: Washington
Posts: 1,964
Bikes: ~'75 Colin Laing, '80s Schwinn SuperSport 650b, ex-Backroads ti project...
Mentioned: 18 Post(s)
Tagged: 0 Thread(s)
Quoted: 525 Post(s)
Liked 931 Times
in
446 Posts
Theyr'e a new enough of rim there should be a wear indicator on the braking surface. I'd use that as a guidline.
Likes For Dylansbob:
#6
Senior Member
Thread Starter
Join Date: Jun 2009
Location: Brooklyn, NY
Posts: 512
Bikes: 1970s Coppi/Fiorelli beater, 1973 Raleigh Competition, 1972 Bob Jackson, 1970 Cilo Sprint-X, 1985 Fuji Touring Series IV, 1969 Legnano Roma
Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 217 Post(s)
Liked 198 Times
in
129 Posts
Likes For niliraga:
#7
2k miles from the midwest
Join Date: Feb 2005
Location: Washington
Posts: 1,964
Bikes: ~'75 Colin Laing, '80s Schwinn SuperSport 650b, ex-Backroads ti project...
Mentioned: 18 Post(s)
Tagged: 0 Thread(s)
Quoted: 525 Post(s)
Liked 931 Times
in
446 Posts
Woof, that's alot of wear.
I've got an old Cane Creek WAM front wheel that looks like that. It lives on a brakeless fixed gear.
I wouldn't put in the effort to build to those.
I've got an old Cane Creek WAM front wheel that looks like that. It lives on a brakeless fixed gear.
I wouldn't put in the effort to build to those.
Likes For Dylansbob:
#8
52psi
Join Date: Aug 2013
Location: Tucson, AZ
Posts: 4,015
Bikes: Schwinn Volare ('78); Raleigh Competition GS ('79)
Mentioned: 29 Post(s)
Tagged: 0 Thread(s)
Quoted: 790 Post(s)
Liked 802 Times
in
391 Posts
__________________
A race bike in any era is a highly personal choice that at its "best" balances the requirements of fit, weight, handling, durability and cost tempered by the willingness to toss it and oneself down the pavement at considerable speed. ~Bandera
A race bike in any era is a highly personal choice that at its "best" balances the requirements of fit, weight, handling, durability and cost tempered by the willingness to toss it and oneself down the pavement at considerable speed. ~Bandera
#9
Mad bike riding scientist
Join Date: Nov 2004
Location: Denver, CO
Posts: 27,359
Bikes: Some silver ones, a red one, a black and orange one, and a few titanium ones
Mentioned: 152 Post(s)
Tagged: 1 Thread(s)
Quoted: 6218 Post(s)
Liked 4,215 Times
in
2,362 Posts
You might as well wrap a turkey in that. It’s about the thickness of aluminum foil now.
Non wise ass answer: Time for a new rim. Ya got your money’s worth.
Non wise ass answer: Time for a new rim. Ya got your money’s worth.
__________________
Stuart Black
Plan Epsilon Around Lake Michigan in the era of Covid
Old School…When It Wasn’t Ancient bikepacking
Gold Fever Three days of dirt in Colorado
Pokin' around the Poconos A cold ride around Lake Erie
Dinosaurs in Colorado A mountain bike guide to the Purgatory Canyon dinosaur trackway
Solo Without Pie. The search for pie in the Midwest.
Picking the Scablands. Washington and Oregon, 2005. Pie and spiders on the Columbia River!
Stuart Black
Plan Epsilon Around Lake Michigan in the era of Covid
Old School…When It Wasn’t Ancient bikepacking
Gold Fever Three days of dirt in Colorado
Pokin' around the Poconos A cold ride around Lake Erie
Dinosaurs in Colorado A mountain bike guide to the Purgatory Canyon dinosaur trackway
Solo Without Pie. The search for pie in the Midwest.
Picking the Scablands. Washington and Oregon, 2005. Pie and spiders on the Columbia River!
#10
Senior Member
Join Date: Jun 2006
Posts: 20,305
Mentioned: 130 Post(s)
Tagged: 0 Thread(s)
Quoted: 3464 Post(s)
Liked 2,828 Times
in
1,995 Posts
I would not buy another set so worn.
As said earlier, impressive wear.
I would keep them around to stretch Kevlar bead tires with. Actually I am intending to make a rim into just that, cut a section out and add parts to turn a rim into a bead stretcher.
the Kevlar beads always stretch out a bit and later installs are much easier but the first install is always much effort.
As said earlier, impressive wear.
I would keep them around to stretch Kevlar bead tires with. Actually I am intending to make a rim into just that, cut a section out and add parts to turn a rim into a bead stretcher.
the Kevlar beads always stretch out a bit and later installs are much easier but the first install is always much effort.
Likes For repechage:
#11
Senior Member
Thread Starter
Join Date: Jun 2009
Location: Brooklyn, NY
Posts: 512
Bikes: 1970s Coppi/Fiorelli beater, 1973 Raleigh Competition, 1972 Bob Jackson, 1970 Cilo Sprint-X, 1985 Fuji Touring Series IV, 1969 Legnano Roma
Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 217 Post(s)
Liked 198 Times
in
129 Posts
well, that'll learn me!! thank you all for the collective wisdom - sounds like they are good for wheelbuilding practice but should never see another brake pad.
well, seller must have known they were far gone - at least they came at a "fully disposable" price.
more generally for rims, if/when i work out how to get past the hook and measure actual wall thickness, what is the thickness most of you would consider the limit? much as how chain stretch sets yellow flags at 0.5 and red at 0.75%, is there an equivalent here?
well, seller must have known they were far gone - at least they came at a "fully disposable" price.
more generally for rims, if/when i work out how to get past the hook and measure actual wall thickness, what is the thickness most of you would consider the limit? much as how chain stretch sets yellow flags at 0.5 and red at 0.75%, is there an equivalent here?
Last edited by niliraga; 04-02-21 at 07:40 AM.
#12
Senior Member
Thread Starter
Join Date: Jun 2009
Location: Brooklyn, NY
Posts: 512
Bikes: 1970s Coppi/Fiorelli beater, 1973 Raleigh Competition, 1972 Bob Jackson, 1970 Cilo Sprint-X, 1985 Fuji Touring Series IV, 1969 Legnano Roma
Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 217 Post(s)
Liked 198 Times
in
129 Posts
I would not buy another set so worn.
As said earlier, impressive wear.
I would keep them around to stretch Kevlar bead tires with. Actually I am intending to make a rim into just that, cut a section out and add parts to turn a rim into a bead stretcher.
the Kevlar beads always stretch out a bit and later installs are much easier but the first install is always much effort.
As said earlier, impressive wear.
I would keep them around to stretch Kevlar bead tires with. Actually I am intending to make a rim into just that, cut a section out and add parts to turn a rim into a bead stretcher.
the Kevlar beads always stretch out a bit and later installs are much easier but the first install is always much effort.
#13
Mad bike riding scientist
Join Date: Nov 2004
Location: Denver, CO
Posts: 27,359
Bikes: Some silver ones, a red one, a black and orange one, and a few titanium ones
Mentioned: 152 Post(s)
Tagged: 1 Thread(s)
Quoted: 6218 Post(s)
Liked 4,215 Times
in
2,362 Posts
well, that'll learn me!! thank you all for the collective wisdom - sounds like they are good for wheelbuilding practice but should never see another brake pad.
well, seller must have known they were far gone - at least they came at a "fully disposable" price.
more generally for rims, if/when i work out how to get past the hook and measure actual wall thickness, what is the thickness most of you would consider the limit? much as how chain stretch sets yellow flags at 0.5 and red at 0.75%, is there an equivalent here?
well, seller must have known they were far gone - at least they came at a "fully disposable" price.
more generally for rims, if/when i work out how to get past the hook and measure actual wall thickness, what is the thickness most of you would consider the limit? much as how chain stretch sets yellow flags at 0.5 and red at 0.75%, is there an equivalent here?
The concavity of the rim may not be just wear related. When you pressurize the tire, the force of the air pushes out on the wall of the rim. As you thin the rim through braking, the pressure can bend the wall outward. Get the wall too thin and it will fracture. I got to witness this is real time at my co-op when an obstinate customer ignored our advice that his rims were very concave...not even as much as yours. We could see the wall flex as he pressurized the tires and told him it was going to fail. We thought that it would fail down the road but about 15 minutes later we had a blowout with a nice ring of aluminum from where the wall had fractured.
__________________
Stuart Black
Plan Epsilon Around Lake Michigan in the era of Covid
Old School…When It Wasn’t Ancient bikepacking
Gold Fever Three days of dirt in Colorado
Pokin' around the Poconos A cold ride around Lake Erie
Dinosaurs in Colorado A mountain bike guide to the Purgatory Canyon dinosaur trackway
Solo Without Pie. The search for pie in the Midwest.
Picking the Scablands. Washington and Oregon, 2005. Pie and spiders on the Columbia River!
Stuart Black
Plan Epsilon Around Lake Michigan in the era of Covid
Old School…When It Wasn’t Ancient bikepacking
Gold Fever Three days of dirt in Colorado
Pokin' around the Poconos A cold ride around Lake Erie
Dinosaurs in Colorado A mountain bike guide to the Purgatory Canyon dinosaur trackway
Solo Without Pie. The search for pie in the Midwest.
Picking the Scablands. Washington and Oregon, 2005. Pie and spiders on the Columbia River!
#14
52psi
Join Date: Aug 2013
Location: Tucson, AZ
Posts: 4,015
Bikes: Schwinn Volare ('78); Raleigh Competition GS ('79)
Mentioned: 29 Post(s)
Tagged: 0 Thread(s)
Quoted: 790 Post(s)
Liked 802 Times
in
391 Posts
For future reference, modern rims will typically have a little "divot" in them. When the wear reaches a point that the divot is no longer visible, they're toast.
Tires will often have them too.
Tires will often have them too.
__________________
A race bike in any era is a highly personal choice that at its "best" balances the requirements of fit, weight, handling, durability and cost tempered by the willingness to toss it and oneself down the pavement at considerable speed. ~Bandera
A race bike in any era is a highly personal choice that at its "best" balances the requirements of fit, weight, handling, durability and cost tempered by the willingness to toss it and oneself down the pavement at considerable speed. ~Bandera
Last edited by Fahrenheit531; 04-02-21 at 09:39 AM.
#15
Senior Member
Thread Starter
Join Date: Jun 2009
Location: Brooklyn, NY
Posts: 512
Bikes: 1970s Coppi/Fiorelli beater, 1973 Raleigh Competition, 1972 Bob Jackson, 1970 Cilo Sprint-X, 1985 Fuji Touring Series IV, 1969 Legnano Roma
Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 217 Post(s)
Liked 198 Times
in
129 Posts
i have some Mavic Open Sports with a wear indicator "ring" machined into the walls, and have seen plenty of generic rims with similar, but I am curious to know if rims that seem to be aiming for retro looks (TB14s, many from VO etc.) put some other kind of indicator that doesnt detract from the look.
#16
Senior Member
Join Date: Oct 2005
Location: Upper Left, USA
Posts: 1,915
Mentioned: 50 Post(s)
Tagged: 0 Thread(s)
Quoted: 634 Post(s)
Liked 444 Times
in
298 Posts
well, that'll learn me!! thank you all for the collective wisdom - sounds like they are good for wheelbuilding practice but should never see another brake pad.
well, seller must have known they were far gone - at least they came at a "fully disposable" price.
more generally for rims, if/when i work out how to get past the hook and measure actual wall thickness, what is the thickness most of you would consider the limit? much as how chain stretch sets yellow flags at 0.5 and red at 0.75%, is there an equivalent here?
well, seller must have known they were far gone - at least they came at a "fully disposable" price.
more generally for rims, if/when i work out how to get past the hook and measure actual wall thickness, what is the thickness most of you would consider the limit? much as how chain stretch sets yellow flags at 0.5 and red at 0.75%, is there an equivalent here?
Likes For tricky:
#17
52psi
Join Date: Aug 2013
Location: Tucson, AZ
Posts: 4,015
Bikes: Schwinn Volare ('78); Raleigh Competition GS ('79)
Mentioned: 29 Post(s)
Tagged: 0 Thread(s)
Quoted: 790 Post(s)
Liked 802 Times
in
391 Posts
TB-14:
And by no means does it "detract from the look."
And by no means does it "detract from the look."
__________________
A race bike in any era is a highly personal choice that at its "best" balances the requirements of fit, weight, handling, durability and cost tempered by the willingness to toss it and oneself down the pavement at considerable speed. ~Bandera
A race bike in any era is a highly personal choice that at its "best" balances the requirements of fit, weight, handling, durability and cost tempered by the willingness to toss it and oneself down the pavement at considerable speed. ~Bandera
Likes For Fahrenheit531:
#18
Senior Member
Thread Starter
Join Date: Jun 2009
Location: Brooklyn, NY
Posts: 512
Bikes: 1970s Coppi/Fiorelli beater, 1973 Raleigh Competition, 1972 Bob Jackson, 1970 Cilo Sprint-X, 1985 Fuji Touring Series IV, 1969 Legnano Roma
Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 217 Post(s)
Liked 198 Times
in
129 Posts
#20
52psi
Join Date: Aug 2013
Location: Tucson, AZ
Posts: 4,015
Bikes: Schwinn Volare ('78); Raleigh Competition GS ('79)
Mentioned: 29 Post(s)
Tagged: 0 Thread(s)
Quoted: 790 Post(s)
Liked 802 Times
in
391 Posts
They're superb rims. If you're on the fence, just go ahead and click 'buy'.
__________________
A race bike in any era is a highly personal choice that at its "best" balances the requirements of fit, weight, handling, durability and cost tempered by the willingness to toss it and oneself down the pavement at considerable speed. ~Bandera
A race bike in any era is a highly personal choice that at its "best" balances the requirements of fit, weight, handling, durability and cost tempered by the willingness to toss it and oneself down the pavement at considerable speed. ~Bandera
Likes For Fahrenheit531:
#21
Senior Member
Join Date: Jun 2006
Posts: 20,305
Mentioned: 130 Post(s)
Tagged: 0 Thread(s)
Quoted: 3464 Post(s)
Liked 2,828 Times
in
1,995 Posts
#22
Newbie
They're worn out but lots of people ride them like that. Be careful. Move your brake blocks for starters so they bear on the unworn surface.
#23
Senior Member
Join Date: Sep 2017
Location: Eastern Shore, MD
Posts: 2,107
Bikes: Road ready: 1993 Koga Miyata City Liner Touring Hybrid, 1989 Centurion Sport DLX, "I Blame GP" Bridgestone CB-1. Projects: Yea, I got a problem....
Mentioned: 24 Post(s)
Tagged: 0 Thread(s)
Quoted: 753 Post(s)
Liked 737 Times
in
422 Posts
Just to for trivia points, there are 90's era Araya rims that start off concave. Before I got comfortable working on my own wheels, I took a set in to replace a spoke and true the set up. The guy wanted to sell me a new set because these where wore out. I insisted, and the work got done, but I think I had a PIA sur charge added.
#24
Old fart
Join Date: Nov 2004
Location: Appleton WI
Posts: 24,784
Bikes: Several, mostly not name brands.
Mentioned: 153 Post(s)
Tagged: 0 Thread(s)
Quoted: 3587 Post(s)
Liked 3,400 Times
in
1,934 Posts
#25
Senior Member
Join Date: Feb 2008
Location: Peoria, IL
Posts: 4,475
Mentioned: 86 Post(s)
Tagged: 0 Thread(s)
Quoted: 1829 Post(s)
Liked 3,373 Times
in
1,579 Posts
the issue of rim wear gets discussed every so often.
About a year ago, someone presented a way to make a little tool out of an old spoke to permit measuring the rim thickness with an ordinary caliper. I had a Sun CR18 that was getting pretty worn, so I went through the process....
the tool itself.
the thickness of the tool itself, which is needed for a later step.
The tool placed to permit indirect measurement of rim thickness.
measuring the combined thickness of the rim sidewall and tool
of course, the alternative is to make a direct measurement of the rim wall thickness. Not a great option if you might want to use the rim, though.
I replaced this unmachined CR18 with a new machined CR18. The new CR18 had thinner side walls than this worn out CR18.
Steve in Peoria
About a year ago, someone presented a way to make a little tool out of an old spoke to permit measuring the rim thickness with an ordinary caliper. I had a Sun CR18 that was getting pretty worn, so I went through the process....
the tool itself.
the thickness of the tool itself, which is needed for a later step.
The tool placed to permit indirect measurement of rim thickness.
measuring the combined thickness of the rim sidewall and tool
of course, the alternative is to make a direct measurement of the rim wall thickness. Not a great option if you might want to use the rim, though.
I replaced this unmachined CR18 with a new machined CR18. The new CR18 had thinner side walls than this worn out CR18.
Steve in Peoria
Likes For steelbikeguy: