Before I slather this stuff all over another bike...
#1
Full Member
Thread Starter
Before I slather this stuff all over another bike...
A few years ago I bought a tub of grease at the hardware store...
I've been using this grease for any bike work I've done, on my own bikes and on some flips. Lubing bolts, screws, wheel bearings, headset bearings, stem quills, seat posts, brake cables, you get the picture.
It's called LubriMatic High Temperature Disc/Drum Brake Wheel Bearing Grease. Base type: Polyurea
Should I keep on keepin' on with this stuff or what? I'm leaning towards "It's fine".
I've been using this grease for any bike work I've done, on my own bikes and on some flips. Lubing bolts, screws, wheel bearings, headset bearings, stem quills, seat posts, brake cables, you get the picture.
It's called LubriMatic High Temperature Disc/Drum Brake Wheel Bearing Grease. Base type: Polyurea
Should I keep on keepin' on with this stuff or what? I'm leaning towards "It's fine".
#2
Senior Member
Join Date: Jan 2013
Location: Llano Estacado
Posts: 3,702
Bikes: old clunker
Mentioned: 13 Post(s)
Tagged: 0 Thread(s)
Quoted: 684 Post(s)
Likes: 0
Liked 105 Times
in
83 Posts
A few years ago I bought a tub of grease at the hardware store...
I've been using this grease for any bike work I've done, on my own bikes and on some flips. Lubing bolts, screws, wheel bearings, headset bearings, stem quills, seat posts, brake cables, you get the picture.
It's called LubriMatic High Temperature Disc/Drum Brake Wheel Bearing Grease. Base type: Polyurea
Should I keep on keepin' on with this stuff or what? I'm leaning towards "It's fine".
I've been using this grease for any bike work I've done, on my own bikes and on some flips. Lubing bolts, screws, wheel bearings, headset bearings, stem quills, seat posts, brake cables, you get the picture.
It's called LubriMatic High Temperature Disc/Drum Brake Wheel Bearing Grease. Base type: Polyurea
Should I keep on keepin' on with this stuff or what? I'm leaning towards "It's fine".
#3
Banned
probably excessive but bikes don't get hub bearings hot like cars may..
I use grease for boat trailer hubs for its water Resistance excess.
I use grease for boat trailer hubs for its water Resistance excess.
#4
Senior Member
Join Date: Aug 2005
Location: Pittsburgh, PA
Posts: 33,656
Bikes: '96 Litespeed Catalyst, '05 Litespeed Firenze, '06 Litespeed Tuscany, '20 Surly Midnight Special, All are 3x10. It is hilly around here!
Mentioned: 39 Post(s)
Tagged: 0 Thread(s)
Quoted: 2026 Post(s)
Likes: 0
Liked 1,096 Times
in
742 Posts
Bicycles are a very low demand application so almost any grease is useable and most are more than satisfactory. The type you are using is just fine. As above, has it done anything bad in the years you've been using it? I thought not.
#5
Full Member
Thread Starter
Yeah that's what I figured as well. I feel like I've read articles about maintenance that say to use a BICYCLE OIL/GREASE AND NOTHING ELSE!!! But maybe it was more about the chain lubrication and warning against using WD40 or something. That would make sense.
#6
Senior Member
Join Date: Jun 2016
Posts: 214
Bikes: 630 Beach Bike Schwinn Hurricane ATB
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 35 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
I was just thinking about grease today.
Was tidying up the garage and tossing away stuff...and saw this tube of engine assembly grease. I bet it would make good because it is lower viscosity. The typical car wheel bearing grease feels too thick for optium performance on low temp application. marine greases is even thicker. Lighter grease seems like good idea.
I was going to toss it in the trash...but wat y'all think? Can I use engine assembly grease on the wheel bearing of bicycles?
Was tidying up the garage and tossing away stuff...and saw this tube of engine assembly grease. I bet it would make good because it is lower viscosity. The typical car wheel bearing grease feels too thick for optium performance on low temp application. marine greases is even thicker. Lighter grease seems like good idea.
I was going to toss it in the trash...but wat y'all think? Can I use engine assembly grease on the wheel bearing of bicycles?
#7
Full Member
Automotive disc/drum grease is a kinda heavy for bicycles, might make you work a bit harder on the flats, but really is just fine. However, after you finish the tub in like year 2054, i would switch to basic lithium grease if you don't want to buy a tube of Phil (or other esoteric brand) of grease.
#8
Senior Member
Join Date: Aug 2005
Location: Pittsburgh, PA
Posts: 33,656
Bikes: '96 Litespeed Catalyst, '05 Litespeed Firenze, '06 Litespeed Tuscany, '20 Surly Midnight Special, All are 3x10. It is hilly around here!
Mentioned: 39 Post(s)
Tagged: 0 Thread(s)
Quoted: 2026 Post(s)
Likes: 0
Liked 1,096 Times
in
742 Posts
I've always splurged (wasted money?) and used Phil's grease on my bikes. However, I buy it in 640 gm (22.5 oz) tubs so the cost per ounce is much lower than buying it in 3 oz tubes. I use a Dualco refillable mini-grease gun to dispense it and to keep the grease in the big container clean.
It does work well and I have hubs with well over 50,000 miles on them still using the original cones. Is it necessary to use "bicycle specific" grease? Of course not but it does work.
It does work well and I have hubs with well over 50,000 miles on them still using the original cones. Is it necessary to use "bicycle specific" grease? Of course not but it does work.
#9
Senior Member
Join Date: Jul 2008
Location: 25 miles northwest of Boston
Posts: 29,549
Bikes: Bottecchia Sprint, GT Timberline 29r, Marin Muirwoods 29er, Trek FX Alpha 7.0
Mentioned: 112 Post(s)
Tagged: 0 Thread(s)
Quoted: 5224 Post(s)
Liked 3,581 Times
in
2,342 Posts
sounds like it would be good on truck leaf springs
#10
Senior Member
Join Date: Jan 2013
Location: Llano Estacado
Posts: 3,702
Bikes: old clunker
Mentioned: 13 Post(s)
Tagged: 0 Thread(s)
Quoted: 684 Post(s)
Likes: 0
Liked 105 Times
in
83 Posts
Yeah...we use so little grease...why not buy the good stuff made specificially for bicycle. Why risk it if axle grease...brake grease, white grease...boat grease...whatever.
If you do the math the cost of "expensive" Phil's grease is like probably 0.001% of the overall cost of bicycling in a cyclist's life time.
It's no brainer to me to buy the good bicycle grease.
But I just happen to have a tube of axle grease sitting around unused from my trailer-hauling days...so I didn't want to waste it...so I just use it...I might have to buy new grease soon though...I am afraid I might have contaminated the tube last time. So...I think I need to use tubes next time...less likely to premature contamination. And definitely a bicycle specific grease.
If you do the math the cost of "expensive" Phil's grease is like probably 0.001% of the overall cost of bicycling in a cyclist's life time.
It's no brainer to me to buy the good bicycle grease.
But I just happen to have a tube of axle grease sitting around unused from my trailer-hauling days...so I didn't want to waste it...so I just use it...I might have to buy new grease soon though...I am afraid I might have contaminated the tube last time. So...I think I need to use tubes next time...less likely to premature contamination. And definitely a bicycle specific grease.
#11
Friendship is Magic
Join Date: Nov 2010
Location: Sacramento, CA
Posts: 22,984
Bikes: old ones
Mentioned: 304 Post(s)
Tagged: 0 Thread(s)
Quoted: 26418 Post(s)
Liked 10,380 Times
in
7,208 Posts
Grease is oil with a thickening agent called a soap. The soaps may be based on most light metals such as lithium, aluminum, sodium, and calcium. The most "fibrous" of these is aluminum based grease, which is good for sliding applications. It is very water resistant but should never be used in rolling element bearings. The most common and versatile are greases based on lithium soaps. They feature excellent resistance to moisture and flowability for rolling element bearings. They handle heat well and resist thickening with age.
The best greases for most purposes are lithium based and contain molybenum disulphide. Molybdenum disulphide has the property of adhering to ferrous metals the extent that it requires machining to remove it. It continues to provide lubricity afte the grease is gone, as in washed away by solvent for a sort time.
Grease should be specified by NLGI grade, with or without the Moly additive.
The best greases for most purposes are lithium based and contain molybenum disulphide. Molybdenum disulphide has the property of adhering to ferrous metals the extent that it requires machining to remove it. It continues to provide lubricity afte the grease is gone, as in washed away by solvent for a sort time.
Grease should be specified by NLGI grade, with or without the Moly additive.
#12
Senior Member
Some people would put oil in their hub and bottom brackets bearings to save a watt or two on race day, so I don't see the problem with trying a thinner grease. You'll probably just have to replace it sooner.
Also, some hub manufactures -- Chris King, DT Swiss, others -- specify a certain type of grease for their ratchets or ring drive systems.
As far as I can tell, Phil or Park greases are just common greases with a little rust inhibitor, but arguments that some lubricants perform a given task better than others seem valid, not totally marketing BS. Some grease hardens over time, etc. S & S Couplings did a test for thread galling, and endorsed a teflon based grease based on a specific test where they basically pinched a nut and ran a bolt through it again and again until it broke.
Also, some hub manufactures -- Chris King, DT Swiss, others -- specify a certain type of grease for their ratchets or ring drive systems.
As far as I can tell, Phil or Park greases are just common greases with a little rust inhibitor, but arguments that some lubricants perform a given task better than others seem valid, not totally marketing BS. Some grease hardens over time, etc. S & S Couplings did a test for thread galling, and endorsed a teflon based grease based on a specific test where they basically pinched a nut and ran a bolt through it again and again until it broke.
#13
Senior Member
Join Date: Jan 2013
Location: Llano Estacado
Posts: 3,702
Bikes: old clunker
Mentioned: 13 Post(s)
Tagged: 0 Thread(s)
Quoted: 684 Post(s)
Likes: 0
Liked 105 Times
in
83 Posts
Black/white thinking gets further from the truth -- bonus: it costs more than truth.
#14
- Soli Deo Gloria -
Join Date: Aug 2015
Location: Northwest Georgia
Posts: 14,779
Bikes: 2018 Rodriguez Custom Fixed Gear, 2017 Niner RLT 9 RDO, 2015 Bianchi Pista, 2002 Fuji Robaix
Mentioned: 235 Post(s)
Tagged: 0 Thread(s)
Quoted: 6844 Post(s)
Liked 736 Times
in
469 Posts
It probably isn't going to hurt anything but keep in mind that certain jobs and parts require specific lubricants. For example, bottom brackets often specify anti-seize rather than grease.
Sticking to what the parts manufacturer recommends is typically a safe bet.
-Tim-
Sticking to what the parts manufacturer recommends is typically a safe bet.
-Tim-
#15
Senior Member
I bought a tube of Phil grease about 30 years ago and I'm still using it. I obviously don't use much.
#16
Senior Member
Join Date: Jan 2017
Posts: 659
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 195 Post(s)
Liked 207 Times
in
126 Posts
Low viscosity
Automotive disc/drum grease is a kinda heavy for bicycles, might make you work a bit harder on the flats, but really is just fine. However, after you finish the tub in like year 2054, i would switch to basic lithium grease if you don't want to buy a tube of Phil (or other esoteric brand) of grease.
#17
Senior Member
Join Date: Jan 2009
Location: San Diego, CA
Posts: 3,672
Mentioned: 10 Post(s)
Tagged: 0 Thread(s)
Quoted: 836 Post(s)
Liked 1,061 Times
in
745 Posts
Here's an excellent (and long) explanation of greases by forum member Slaninar. https://bike.bikegremlin.com/1985/bi...ase-explained/
#18
Full Member
]Man, if the viscosity of the grease affects your speed you got one finely tuned pair of legs my friend.😁
Ha, nothing I would feel, but on the other hand I need every bit of power I can get, laughing hard.
Ha, nothing I would feel, but on the other hand I need every bit of power I can get, laughing hard.
#19
Senior Member
Join Date: Mar 2012
Location: Wales, UK
Posts: 148
Bikes: Saracen Skyline, Canyon Ultimate, Stanton Switchback, Cotic SolarisMAX
Mentioned: 6 Post(s)
Tagged: 0 Thread(s)
Quoted: 39 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
The main downside IMO is the potential incompatibility of the polyurea base with other greases (which are mostly not urea based). I learned this lesson the hard way after trying out Park Tools grease, which has the same base.
#22
Senior Member
Join Date: Nov 2014
Location: Saratoga calif.
Posts: 1,049
Bikes: Miyata 610(66cm), GT Vantara Hybrid (64cm), Nishiki International (64cm), Peugeot rat rod (62 cm), Trek 800 Burning Man helicopter bike, Bob Jackson frame (to be restored?) plus a never ending stream of neglected waifs from the Bike exchange.
Mentioned: 28 Post(s)
Tagged: 0 Thread(s)
Quoted: 339 Post(s)
Likes: 0
Liked 632 Times
in
229 Posts
At the Bike Exchange we use tubs of lithium grease for all our donation bikes . Have been doing it for 25 years.
Personally, I buy lithium grease in a squeeze tube. It prevents contamination and makes squirting grease into wheel bearing cups, head set and bottom bracket cups a snap. I have been rehabbing a lot of bikes lately and go through a tube maybe every 4-5 months. No big deal.
Also the tube fits in the top shelf of my 3 drawer tool box that I like to bring with me to the Exchange when I work there. Nice to have everything close at hand so I don't have to go over to the tool cart every time I need something.
Personally, I buy lithium grease in a squeeze tube. It prevents contamination and makes squirting grease into wheel bearing cups, head set and bottom bracket cups a snap. I have been rehabbing a lot of bikes lately and go through a tube maybe every 4-5 months. No big deal.
Also the tube fits in the top shelf of my 3 drawer tool box that I like to bring with me to the Exchange when I work there. Nice to have everything close at hand so I don't have to go over to the tool cart every time I need something.
#23
aka Tom Reingold
Join Date: Jan 2009
Location: New York, NY, and High Falls, NY, USA
Posts: 40,503
Bikes: 1962 Rudge Sports, 1971 Raleigh Super Course, 1971 Raleigh Pro Track, 1974 Raleigh International, 1975 Viscount Fixie, 1982 McLean, 1996 Lemond (Ti), 2002 Burley Zydeco tandem
Mentioned: 511 Post(s)
Tagged: 0 Thread(s)
Quoted: 7348 Post(s)
Liked 2,466 Times
in
1,434 Posts
Replacing the grease every year or two is more important than the choice of grease. The grease dries up or cakes up or gets dirty. You can have two different failure modes of the same grease in different years which leads me to believe the choice of grease matters less than the luck of the terrain you ride in. There is no predicting how your grease will fail. I say keep using whatever you've been using. Then again, if you want to buy the expensive stuff, that's fine, too, because, as someone pointed out, that ends up not being expensive in real use.
__________________
Tom Reingold, tom@noglider.com
New York City and High Falls, NY
Blogs: The Experienced Cyclist; noglider's ride blog
“When man invented the bicycle he reached the peak of his attainments.” — Elizabeth West, US author
Please email me rather than PM'ing me. Thanks.
Tom Reingold, tom@noglider.com
New York City and High Falls, NY
Blogs: The Experienced Cyclist; noglider's ride blog
“When man invented the bicycle he reached the peak of his attainments.” — Elizabeth West, US author
Please email me rather than PM'ing me. Thanks.