Problems replacing a spoke
09-05-19, 12:34 PM
#1
Senior Member
Thread Starter
Join Date: Apr 2012
Location: Middle Earth (aka IA)
Posts: 20,435
Bikes: A bunch of old bikes and a few new ones
Mentioned: 178 Post(s)
Tagged: 0 Thread(s)
Quoted: 5888 Post(s)
Liked 3,471 Times
in
2,079 Posts
Problems replacing a spoke
This wheel has been a problem in replacing a broken spoke. The problem is that the spokes overlap the spoke hole so that I can't get a new spoke in. I could slack off the tension on all the spokes but it will be a fair amount of work to retension the wheel. As you can see from the pic, this is the rear wheel, no drive side. Any ideas?
Last edited by bikemig; 09-05-19 at 12:44 PM.
09-05-19, 01:09 PM
#2
Full Member
Just losen the spoke that‘s in the way.
09-05-19, 01:23 PM
#3
Senior Member
Join Date: Dec 2010
Location: northern Deep South
Posts: 8,903
Bikes: Fuji Touring, Novara Randonee
Mentioned: 36 Post(s)
Tagged: 0 Thread(s)
Quoted: 2604 Post(s)
Liked 1,931 Times
in
1,212 Posts
I can't quite see the spoke hole for the problem spoke on the picture. In general, though, just worry about getting the spoke through the hole, then weave it through the other spokes after it's seated (or close to seated).
09-05-19, 01:26 PM
#4
Generally bewildered
Join Date: Aug 2015
Location: Eastern PA, USA
Posts: 3,037
Bikes: 2014 Trek Domane 6.9, 1999 LeMond Zurich, 1978 Schwinn Superior
Mentioned: 20 Post(s)
Tagged: 0 Thread(s)
Quoted: 1152 Post(s)
Liked 341 Times
in
251 Posts
^^^^ This. pdlamb's right.
I suspect that you could put the spoke in at an angle and the head will seat against the flange. You'll have to utilize much of the bendy in the spoke, but that's ok.
If not, I think you can just loosen one spoke to get the head to seat.
I suspect that you could put the spoke in at an angle and the head will seat against the flange. You'll have to utilize much of the bendy in the spoke, but that's ok.
If not, I think you can just loosen one spoke to get the head to seat.
09-05-19, 01:39 PM
#5
Senior Member
Thread Starter
Join Date: Apr 2012
Location: Middle Earth (aka IA)
Posts: 20,435
Bikes: A bunch of old bikes and a few new ones
Mentioned: 178 Post(s)
Tagged: 0 Thread(s)
Quoted: 5888 Post(s)
Liked 3,471 Times
in
2,079 Posts
Right. Yeah it won't sit right (I tried) so loosening one spoke it is.
09-05-19, 01:46 PM
#6
Senior Member
Join Date: Nov 2014
Location: Eugene, Oregon, USA
Posts: 27,547
Mentioned: 217 Post(s)
Tagged: 0 Thread(s)
Quoted: 18375 Post(s)
Liked 4,510 Times
in
3,352 Posts
You could probably safely grind off a portion of the spoke head.
But, as above, it is best to just loosen, or even take loose the offending spoke.
But, as above, it is best to just loosen, or even take loose the offending spoke.
09-05-19, 06:37 PM
#8
Passista
Join Date: Jul 2005
Posts: 7,597
Bikes: 1998 Pinarello Asolo, 1992 KHS Montaña pro, 1980 Raleigh DL-1, IGH Hybrid, IGH Utility
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 866 Post(s)
Liked 721 Times
in
396 Posts
It's normal for a 4 cross build, as said above just loosen 1 spoke.
09-06-19, 08:25 AM
#9
Senior Member
Join Date: Dec 2007
Location: San Jose, California
Posts: 3,504
Bikes: 2001 Tommasini Sintesi w/ Campagnolo Daytona 10 Speed
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 145 Post(s)
Likes: 0
Liked 35 Times
in
30 Posts
Exactly, loosen the one spoke to be replaced...a little wiggling, angling, it'll come out from under the crossing spoke.
=8-)
=8-)
__________________
5000+ wheels built since 1984...
Disclaimer:
1. I do not claim to be an expert in bicycle mechanics despite my experience.
2. I like anyone will comment in other areas.
3. I do not own the preexisting concepts of DISH and ERD.
4. I will provide information as I always have to others that I believe will help them protect themselves from unscrupulous mechanics.
5. My all time favorite book is:
Kahane, Howard. Logic and Contemporary Rhetoric: The Use of Reason in Everyday Life
5000+ wheels built since 1984...
Disclaimer:
1. I do not claim to be an expert in bicycle mechanics despite my experience.
2. I like anyone will comment in other areas.
3. I do not own the preexisting concepts of DISH and ERD.
4. I will provide information as I always have to others that I believe will help them protect themselves from unscrupulous mechanics.
5. My all time favorite book is:
Kahane, Howard. Logic and Contemporary Rhetoric: The Use of Reason in Everyday Life
