Vintage Touring Bike with Modern Components - Will it Work?
#51
Senior Member
Join Date: Apr 2005
Location: Ann Arbor, MI
Posts: 16,874
Bikes: 1980 Masi, 1984 Mondonico, 1984 Trek 610, 1980 Woodrup Giro, 2005 Mondonico Futura Leggera ELOS, 1967 PX10E, 1971 Peugeot UO-8
Mentioned: 49 Post(s)
Tagged: 0 Thread(s)
Quoted: 1856 Post(s)
Liked 664 Times
in
506 Posts
I wouldn't worry. It'd have to be a pretty strange failure to:
a) not be visible after the frame is spread
b) fail catastrophically. At least it should creak first, and steel fails quite gracefully.
c) fail in a way that causes a crash.
I've seen frames crack in the seat stays and chain stays and these cracks cause some odd handling and creaks to say the least, which gives the rider warning long before anything catastrophic might happen. The wheel stays where it should be. I can't really fathom a safety issue, which is why I didn't mention it. I am sure it has happened, once (think the cliché about monkeys on typewriters eventually will write Shakespeare), but who knows the other factors involved (ignoring creaks and changes in handling is not a good idea).
Because you're smart and you trust yourself to notice if something goes wrong, before it hurts you. That's not hypocrisy. It's a basic survival skill.
a) not be visible after the frame is spread
b) fail catastrophically. At least it should creak first, and steel fails quite gracefully.
c) fail in a way that causes a crash.
I've seen frames crack in the seat stays and chain stays and these cracks cause some odd handling and creaks to say the least, which gives the rider warning long before anything catastrophic might happen. The wheel stays where it should be. I can't really fathom a safety issue, which is why I didn't mention it. I am sure it has happened, once (think the cliché about monkeys on typewriters eventually will write Shakespeare), but who knows the other factors involved (ignoring creaks and changes in handling is not a good idea).
Because you're smart and you trust yourself to notice if something goes wrong, before it hurts you. That's not hypocrisy. It's a basic survival skill.
#52
Senior Member
Join Date: Apr 2005
Location: Ann Arbor, MI
Posts: 16,874
Bikes: 1980 Masi, 1984 Mondonico, 1984 Trek 610, 1980 Woodrup Giro, 2005 Mondonico Futura Leggera ELOS, 1967 PX10E, 1971 Peugeot UO-8
Mentioned: 49 Post(s)
Tagged: 0 Thread(s)
Quoted: 1856 Post(s)
Liked 664 Times
in
506 Posts
Likes For Road Fan:
#53
Full Member
One thing I’ll add is that a Jtek shiftmate or Wolftooth tanpan can be used to get modern road shifters and MTB rear derailleurs working well together. That’ll further open up gearing options if needed. Start there - determine desired gear range - and work backwards to your components.
I built this bike with a very low gear for carrying a load up off road climbs. Gearing is 46/30 SunXCD ramped and pinned chainrings on a 49d crankset, 11-42 XT 11sp cassette on a Dura Ace 9000 rear hub. Ultegra 8000 series STI levers and front derailleur, XTR M9000 rear derailleur with the appropriate Jtek shiftmate to make it work. I’m very happy with this setup.
Please keep us updated as you work through the build!
I built this bike with a very low gear for carrying a load up off road climbs. Gearing is 46/30 SunXCD ramped and pinned chainrings on a 49d crankset, 11-42 XT 11sp cassette on a Dura Ace 9000 rear hub. Ultegra 8000 series STI levers and front derailleur, XTR M9000 rear derailleur with the appropriate Jtek shiftmate to make it work. I’m very happy with this setup.
Please keep us updated as you work through the build!
Likes For Schlafen:
#54
Extraordinary Magnitude
Join Date: Aug 2009
Location: Waukesha WI
Posts: 13,646
Bikes: 1978 Trek TX700; 1978/79 Trek 736; 1984 Specialized Stumpjumper Sport; 1984 Schwinn Voyageur SP; 1985 Trek 620; 1985 Trek 720; 1986 Trek 400 Elance; 1987 Schwinn High Sierra; 1990 Miyata 1000LT
Mentioned: 84 Post(s)
Tagged: 0 Thread(s)
Quoted: 2608 Post(s)
Liked 1,699 Times
in
935 Posts
I really love them- I don't like the look of the new ones- but I do like that they wouldn't catch on some of my shorts like the older cloth ones do.
__________________
*Recipient of the 2006 Time Magazine "Person Of The Year" Award*
Commence to jigglin’ huh?!?!
"But hey, always love to hear from opinionated amateurs." -says some guy to Mr. Marshall.
Commence to jigglin’ huh?!?!
"But hey, always love to hear from opinionated amateurs." -says some guy to Mr. Marshall.
#55
Member
Unlike many here, my bike mechanic skills are pretty limited. I change flats, clean and lube chains, adjust non-disk brakes, replace jockey wheels, change chains,and beyond that, it gets iffier, especially since I don't have the tools and my local bike coop is basically closed due to COVID. I wound up using my local bike shop, Bullseye Bicycles of Durham, N.C. I also don't have a garage full of old bicycle parts. Anyway, here's my 1986 Univega Gran Turismo before and after. In my case, I'm not planning any loaded tours with it, so went for more of a gravel-lite thing-- I don't really do challenging single track any longer either. I spent most of the money on wheels (H plus Son). I happened to get a pretty good deal on a Sora 3000 groupset. I don't race. In fact, I sometimes get passed by riders older than I on rusty English Racer type bikes or, even worse, on Elliptigos. I do draw the line with adult trikes. Anyway, I just wanted a groupset that shifts when it's supposed to. It did change the look quite a bit. Almost everything that used to be silver is now black. The visual change might horrify the restorationists, but I don't regret "modernizing."
I found that I prefer brifters, especially off road. I did make the questionable decision to go from 3x to 2x, but I honestly hadn't used to granny gear in some time and the hills here aren't that steep or long. Going to 9 speed does give me a couple more ratios that I actually use. Going to the brifters also eliminates the brake cables coming out of the hoods and added the over the hoods hand position which I use a lot, especially uphill. The result is a very comfortable bike that I wind up going 10 miles further than I originally intended that I can take on pretty much any road/path that isn't either mud or boulders. Bullseye did a really good job and they worked with me in letting me hunt for parts on e-bay and bring them in for the rebuild.
I found that I prefer brifters, especially off road. I did make the questionable decision to go from 3x to 2x, but I honestly hadn't used to granny gear in some time and the hills here aren't that steep or long. Going to 9 speed does give me a couple more ratios that I actually use. Going to the brifters also eliminates the brake cables coming out of the hoods and added the over the hoods hand position which I use a lot, especially uphill. The result is a very comfortable bike that I wind up going 10 miles further than I originally intended that I can take on pretty much any road/path that isn't either mud or boulders. Bullseye did a really good job and they worked with me in letting me hunt for parts on e-bay and bring them in for the rebuild.
Likes For chancelucky:
#56
Sunshine
Join Date: Aug 2014
Location: Des Moines, IA
Posts: 16,614
Bikes: '18 class built steel roadbike, '19 Fairlight Secan, '88 Schwinn Premis , Black Mountain Cycles Monstercross V4, '89 Novara Trionfo
Mentioned: 123 Post(s)
Tagged: 0 Thread(s)
Quoted: 10963 Post(s)
Liked 7,489 Times
in
4,189 Posts
Likes For mstateglfr:
#57
Full Member
Join Date: Sep 2019
Posts: 393
Mentioned: 18 Post(s)
Tagged: 0 Thread(s)
Quoted: 170 Post(s)
Liked 264 Times
in
146 Posts
My buddy and I are planning on doing a tour of Colorado this coming summer (starting and ending in the mountains, lots of climbs, camping at night, etc.). We love the look and feel of vintage steel bikes, but don't relish the thought of trying to do a mountain tour on a 10 or 12 speed with vintage components. We are toying with the idea of putting modern components (think something like Shimano 105 with a triple crank) on a vintage frame, but are unsure if it will work. I understand the rear fork spacing will need to be cold-set from 1XXmm to 130mm to accommodate a 10 - 12 speed cassette, the bottom bracket will need to be sorted out in order to accommodate a modern crankset, potentially replacing brakes for long reach if we go from a 27" to 700c tire, and possibly getting a stem adapter if we don't want to go with a quill stem, but what else am I missing? Is it even feasible? I understand the changes will cost money and time, and that's fine just trying to see if it can even be done and if worthwhile. I have a thing for Specialized bikes so I was thinking an early to mid 80s Specialized Expedition and he's British so he was looking at a Raleigh Portage. Any thoughts or insight would be great. Thank you!
Here's my 2x9/10 speed 83 Pro Tour 15
- Rear triangle spread to 128mm, works well with many modern wheelsets
- 700c conversion (swapped to cantis with more room for adjustment)
- fits 38mm gravel tires or 35 and fenders (as pictured)
- Compact 50/34 chainset and 11/32t cassette, which is all the range I need for light touring in the PNW
- Long cage Deore xt rear derailleur, dirt drop bars with extra grips
Likes For ctak:
#58
Full Member
Join Date: Feb 2013
Location: Worcester, Massachusetts
Posts: 308
Bikes: Fuji Sportif 1.7C, Shogun Metro AT, Jamis Durango SX, Miyata Alumicross, Fuji Special Road Racer, Mongoose ATB, Fuji SST 1.0 Team, Gitane (?), Specialized Rockhopper SS, Univega Gran Turismo, Univega Supra Sport Mixte, Nishiki Tri-A, Diamondback Coil
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 82 Post(s)
Liked 141 Times
in
78 Posts
Unlike many here, my bike mechanic skills are pretty limited. I change flats, clean and lube chains, adjust non-disk brakes, replace jockey wheels, change chains,and beyond that, it gets iffier, especially since I don't have the tools and my local bike coop is basically closed due to COVID. I wound up using my local bike shop, Bullseye Bicycles of Durham, N.C. I also don't have a garage full of old bicycle parts. Anyway, here's my 1986 Univega Gran Turismo before and after. In my case, I'm not planning any loaded tours with it, so went for more of a gravel-lite thing-- I don't really do challenging single track any longer either. I spent most of the money on wheels (H plus Son). I happened to get a pretty good deal on a Sora 3000 groupset. I don't race. In fact, I sometimes get passed by riders older than I on rusty English Racer type bikes or, even worse, on Elliptigos. I do draw the line with adult trikes. Anyway, I just wanted a groupset that shifts when it's supposed to. It did change the look quite a bit. Almost everything that used to be silver is now black. The visual change might horrify the restorationists, but I don't regret "modernizing."
I found that I prefer brifters, especially off road. I did make the questionable decision to go from 3x to 2x, but I honestly hadn't used to granny gear in some time and the hills here aren't that steep or long. Going to 9 speed does give me a couple more ratios that I actually use. Going to the brifters also eliminates the brake cables coming out of the hoods and added the over the hoods hand position which I use a lot, especially uphill. The result is a very comfortable bike that I wind up going 10 miles further than I originally intended that I can take on pretty much any road/path that isn't either mud or boulders. Bullseye did a really good job and they worked with me in letting me hunt for parts on e-bay and bring them in for the rebuild.
I found that I prefer brifters, especially off road. I did make the questionable decision to go from 3x to 2x, but I honestly hadn't used to granny gear in some time and the hills here aren't that steep or long. Going to 9 speed does give me a couple more ratios that I actually use. Going to the brifters also eliminates the brake cables coming out of the hoods and added the over the hoods hand position which I use a lot, especially uphill. The result is a very comfortable bike that I wind up going 10 miles further than I originally intended that I can take on pretty much any road/path that isn't either mud or boulders. Bullseye did a really good job and they worked with me in letting me hunt for parts on e-bay and bring them in for the rebuild.
Likes For PugRider:
#59
Newbie
Join Date: Jan 2021
Posts: 3
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
new parts on old frames
My buddy and I are planning on doing a tour of Colorado this coming summer (starting and ending in the mountains, lots of climbs, camping at night, etc.). We love the look and feel of vintage steel bikes, but don't relish the thought of trying to do a mountain tour on a 10 or 12 speed with vintage components. We are toying with the idea of putting modern components (think something like Shimano 105 with a triple crank) on a vintage frame, but are unsure if it will work. I understand the rear fork spacing will need to be cold-set from 1XXmm to 130mm to accommodate a 10 - 12 speed cassette, the bottom bracket will need to be sorted out in order to accommodate a modern crankset, potentially replacing brakes for long reach if we go from a 27" to 700c tire, and possibly getting a stem adapter if we don't want to go with a quill stem, but what else am I missing? Is it even feasible? I understand the changes will cost money and time, and that's fine just trying to see if it can even be done and if worthwhile. I have a thing for Specialized bikes so I was thinking an early to mid 80s Specialized Expedition and he's British so he was looking at a Raleigh Portage. Any thoughts or insight would be great. Thank you!
Yes, it´s very possible. I rebuilt an `86 Eddy Merckx Corsa Extra with modern Campagnolo Record group, with the exception of the chainset, which is a lower group model (Centaur) due to the BB being square tapered. I did this purely because a friend built gave me a pair of wheels with Campag 10spd Record hubs. Cold setting the rear triangle is pretty easy. It´s handy if the frame you´re planning to use has braze-ons for the front shifter due to changes in tube diameters meaning modern clamps wont always fit older frames. Dual pivot brakes are excellent and infinitely better than the old rim brakes, I didnt need to use long reach ones to accommodate a 700c rim. Some fiddly adaptations of mounting bolts (sourcing shorter recessed bolts etc) were needed, so a little time and patience required. But she looks great and rides like a dream. Took her up Alp D`huez in France a couple of years ago on her inaugural tour, handled like a dream doing 93kmh (58mph) on the descent, and drew a lot of attention at the cafe at the top.
Good luck with the build, it will be worth it!
#60
resykler
Join Date: Oct 2020
Location: S.F.
Posts: 201
Bikes: Bianchi Eros, Bianchi Reparto Corsa, Mongoose IBOC Campagnolo, Schwinn Super Sport, Mairag 4 Star, Canondale Criterium, Centurion Accordo RS, Specialized Hard Rock 1st Gen, Bianchi Special '81
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 101 Post(s)
Liked 59 Times
in
39 Posts
Univega Upgrade
Swapped everything I could, shifters
Bars, brakes
Wheels, gearset. Ignore the chain I hadn't finished but you get the idea. If I had something nice I wasn't using it got a home on the Univega. Sorry about the crappy paint job
Likes For brixxton:
#61
Sunshine
Join Date: Aug 2014
Location: Des Moines, IA
Posts: 16,614
Bikes: '18 class built steel roadbike, '19 Fairlight Secan, '88 Schwinn Premis , Black Mountain Cycles Monstercross V4, '89 Novara Trionfo
Mentioned: 123 Post(s)
Tagged: 0 Thread(s)
Quoted: 10963 Post(s)
Liked 7,489 Times
in
4,189 Posts
^ You definitely made it your own. A Pearl stem with the bar that is quite a juxtaposition.
Just watch the front brake setup since the plastic part of the housing is now missing- dont want it to continue to deteriorate.
Just watch the front brake setup since the plastic part of the housing is now missing- dont want it to continue to deteriorate.
#62
resykler
Join Date: Oct 2020
Location: S.F.
Posts: 201
Bikes: Bianchi Eros, Bianchi Reparto Corsa, Mongoose IBOC Campagnolo, Schwinn Super Sport, Mairag 4 Star, Canondale Criterium, Centurion Accordo RS, Specialized Hard Rock 1st Gen, Bianchi Special '81
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 101 Post(s)
Liked 59 Times
in
39 Posts
Test Bed
I had no idea what a following these Univega had. When I first got it the paint scheme was to much to handle, but we've been on a steep learning curve together and I can't see me letting it go.
#63
Junior Member
Join Date: Dec 2010
Location: Maryland
Posts: 144
Bikes: 2008 Specialized Roubaix Elite, 2002 Specialized Sirius Pro, 1985 Vitus 979 (DuraAce 7400), 1985 Bianchi Trofeo
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 53 Post(s)
Likes: 0
Liked 25 Times
in
15 Posts
We just like the idea of different / more gears, brifters instead of downtube shifting, etc. We both have vintage road bike and enjoy them, but want something slightly different for touring purposes. As for a LBS, I restore and sell vintage bikes, so no need to get a LBS involved for any of this.
There are other similar volume production manufacturers of steel framed bikes.
#64
Senior Member
Thread Starter
That was originally the plan, but we like the idea of touring on vintage steel bikes. Just our preference this time around. It's not simply about the bikes being steel, but 80s steel.
#68
Senior Member
Join Date: Jan 2017
Posts: 659
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 195 Post(s)
Liked 207 Times
in
126 Posts
My buddy and I are planning on doing a tour of Colorado this coming summer (starting and ending in the mountains, lots of climbs, camping at night, etc.). We love the look and feel of vintage steel bikes, but don't relish the thought of trying to do a mountain tour on a 10 or 12 speed with vintage components. We are toying with the idea of putting modern components (think something like Shimano 105 with a triple crank) on a vintage frame, but are unsure if it will work. I understand the rear fork spacing will need to be cold-set from 1XXmm to 130mm to accommodate a 10 - 12 speed cassette, the bottom bracket will need to be sorted out in order to accommodate a modern crankset, potentially replacing brakes for long reach if we go from a 27" to 700c tire, and possibly getting a stem adapter if we don't want to go with a quill stem, but what else am I missing? Is it even feasible? I understand the changes will cost money and time, and that's fine just trying to see if it can even be done and if worthwhile. I have a thing for Specialized bikes so I was thinking an early to mid 80s Specialized Expedition and he's British so he was looking at a Raleigh Portage. Any thoughts or insight would be great. Thank you!
The upgrades you plan are definitely doable. Here's a nice uo-10 converted to a dandy touring bike. I'd say a triple is a must in Colorado but 7 is plenty for the gearset. There are also plenty of 7 speed shifters to be had. I never found a six or even a 5 speed freewheel to offer any real obstacle to touring. It's the wide range that's needed. A 5 speed freewheel with half step gearing gives you plenty of choices. I've gotten lazy over the years and settled on a seven speed gearset as just easier to use and skipped the half step preferring the range approach for the triple. Also it's easier to adopt an older bike to expand to a seven speed freewheel or cassette.
#69
Senior Member
Join Date: Jan 2017
Posts: 659
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 195 Post(s)
Liked 207 Times
in
126 Posts
Several have mentioned adding drop bars to a mtn bike but consider a vintage hybrid. It's easy to find tires. They usually have bosses for racks even low rider bosses and they already have cantilever brakes. What's not to like?😁
#70
resykler
Join Date: Oct 2020
Location: S.F.
Posts: 201
Bikes: Bianchi Eros, Bianchi Reparto Corsa, Mongoose IBOC Campagnolo, Schwinn Super Sport, Mairag 4 Star, Canondale Criterium, Centurion Accordo RS, Specialized Hard Rock 1st Gen, Bianchi Special '81
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 101 Post(s)
Liked 59 Times
in
39 Posts
Feasible
Absolutely and I applaud your choice to go true vintage steel. If you have the skill set and a quality frame you end up with something that's yours, unique and has soul!
Last edited by brixxton; 01-26-21 at 09:44 PM. Reason: Pix
Likes For brixxton:
#71
Full Member
Join Date: Sep 2019
Posts: 393
Mentioned: 18 Post(s)
Tagged: 0 Thread(s)
Quoted: 170 Post(s)
Liked 264 Times
in
146 Posts
KoolStop Thinlines https://www.jensonusa.com/Kool-Stop-...ed-Post-Salmon
Likes For ctak:
#72
Junior Member
Join Date: Dec 2010
Location: Maryland
Posts: 144
Bikes: 2008 Specialized Roubaix Elite, 2002 Specialized Sirius Pro, 1985 Vitus 979 (DuraAce 7400), 1985 Bianchi Trofeo
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 53 Post(s)
Likes: 0
Liked 25 Times
in
15 Posts
There are plenty of 80s touring bikes you can customize to your liking with modern parts. You can go 7 speed w/o adjusting the frame, or even 8/9 speed if you do the Sheldon Brown 8 of 9 on 7 method. The Microshift 7 speed brifters are excellent.
8 Of 9 On 7 -- or 9 of 10 on 7
If your 126 mm frame is aluminum, carbon fiber or held together by glue, you shouldn't try to spread it. That still doesn't mean that you're stuck with 7 speeds!Any 7-speed Shimano Hyperglide Freehub will actually work with 8 or 9 sprockets, without any modification! What you need to do is to use 8 of the sprockets from a 9-speed cassette, with the 9-speed spacers -- or 9 of the sprockets from a 10-speed cassette. This trick also is useful when cassette body transplantation isn't possible -- on an off-brand hub or a Sachs 3 x 7 hybrid-gearing hub.
To make this work, you'll also need to use a 9- or 10-speed chain and shifters. Your old 7-speed derailer (except 1996 or earlier Dura-Ace) should work OK if it isn't too badly worn. Most, but not all, 9- and 10-speed shifters will work.
The limit stops on the derailer will cause the useless position on the shifter to be locked out, so this will work as a perfectly normal 8- or 9-speed rig.
https://www.sheldonbrown.com/k7.html
Likes For GregU:
#73
Senior Member
Join Date: Nov 2014
Location: Ann Arbor Michigan
Posts: 152
Bikes: miyata 83 1000,84 1000,83 610,88 ridge runner ,Schwinn 84 high sierra,88 Cimmeron,86 Passage,84 Stumplumper ,83 Mt Whitney,83 Trek 850,Merckx Century,PX10, RB1,XO 1 XO 4,bunch of stuff like that
Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 57 Post(s)
Liked 51 Times
in
42 Posts
you asked
Since you asked here is what Homelessjoe has to say.......If you find an old Specialized Expedition or a Portage.....those bikes are beautiful and bombproof as it is......they were designed to do exactly what you want to do and go where you want to go......you cant improve perfect........you could drive them across Siberia and depend on then to bringing you home.........as is.........with a quill stem you can adjust your bar hight when ever you want........its amazing what a relief it is on your back and butt to change your riding position just an inch higher or lower after a long day.......I think quill stems are a must for long distance touring.........dont cold set that frame.....when those bikes left the factory they were perfectly precision laser beam straight........going down the road in a straight line is a must on a long ride......if your are snaking down the road and snaking up hills it will wear you out to fast because you will keep using you upper body trying to balance.....both the Specialized and the Portage are 21 speeds....and the components are better than 105.....they are stronger....you dont need to change anything.......if in good condition the are ready to go.....you may want to change a chainring or a gear or two depending how strong you are.....but adding more gears wont help nothing.......fresh double butted spokes is a good place to spend your money...you will be amazed what a broken spoke will do to your disposition when you are 35 miles from nothing......new tires ...grease........get the best seat there is.......and dont get a new untried seat and head off for the great divide......try it out for a week or two.... break it in......I wish I was going with you.....I was there two years ago
Last edited by homelessjoe; 01-29-21 at 12:49 AM. Reason: misspelled
#74
Junior Member
Join Date: Oct 2021
Posts: 5
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4 Post(s)
Likes: 0
Liked 2 Times
in
2 Posts
I'm in the same position as the OP. I have a 1990 Trek 750 that I would like to use to do some long distance touring. This bike has 32 spoke wheels and I'm definitely going to upgrade the real wheel to a strong 36 spoke wheel. Do you think it would be ok to leave the original 32 spoke wheel in the front? I weight about 240 lb and I am planing to use 2 panniers in the front and 2 in the back, although I don't know how much gear I will be carrying yet, since this is the first time I will be doing this.
Your answers are greatly appreciated.
Your answers are greatly appreciated.
#75
ambulatory senior
Join Date: Dec 2016
Location: Peoria Il
Posts: 5,998
Bikes: Austro Daimler modified by Gugie! Raleigh Professional and lots of other bikes.
Mentioned: 76 Post(s)
Tagged: 0 Thread(s)
Quoted: 1955 Post(s)
Liked 3,661 Times
in
1,679 Posts
I'm in the same position as the OP. I have a 1990 Trek 750 that I would like to use to do some long distance touring. This bike has 32 spoke wheels and I'm definitely going to upgrade the real wheel to a strong 36 spoke wheel. Do you think it would be ok to leave the original 32 spoke wheel in the front? I weight about 240 lb and I am planing to use 2 panniers in the front and 2 in the back, although I don't know how much gear I will be carrying yet, since this is the first time I will be doing this.
Your answers are greatly appreciated.
Your answers are greatly appreciated.