It's funny how every tire mounting experience differs.
#1
Newbie
Thread Starter
It's funny how every tire mounting experience differs.
I just finished putting 4 new tires on 2 bikes for the 2024 season.
I mounted a 2.4 inch Maxxis Race Rekon and 2.4 inch Maxxis Forekaster onto a Trek Roscoe 8 that had OEM Trek XR4 Team Issue 2.6 inch tires. Those tires were fine but I'm making the Roscoe more of a X-Country bike. Both were surprisingly easy with just a smidge of tire lever at the end. I didn't even have a charge pump or air compressor- I just used a Joe Blow floor pump and both tubeless tires seated with a normal tire pumping pace.
Next I put 2 Schwalbe G One Overland 700x45 tires on a Flatbike Gravel bike with Shimano WH-RX010 rims. This bike is a tube set up and despite the inner rim being 17mm and Shimano suggesting a maximum of 38mm tires, I googled and the consensus was I was ok putting up to 51mm tires on a 17mm inner rim.
I would post pictures but I don't want to ruin anyone's lunch. Needless to say my fingers are torn up trying to get the tires to seat evenly on the manufacturers line with the rim. It was at least a half hour of pulling in various spots and tearing up the inner pads on my fingers in two places. I should have used soap but just used brute force.
I've come to the conclusion every tire and rim situation is so unique you can never count a review saying "Easy to mount" or "Hard to mount".
I mounted a 2.4 inch Maxxis Race Rekon and 2.4 inch Maxxis Forekaster onto a Trek Roscoe 8 that had OEM Trek XR4 Team Issue 2.6 inch tires. Those tires were fine but I'm making the Roscoe more of a X-Country bike. Both were surprisingly easy with just a smidge of tire lever at the end. I didn't even have a charge pump or air compressor- I just used a Joe Blow floor pump and both tubeless tires seated with a normal tire pumping pace.
Next I put 2 Schwalbe G One Overland 700x45 tires on a Flatbike Gravel bike with Shimano WH-RX010 rims. This bike is a tube set up and despite the inner rim being 17mm and Shimano suggesting a maximum of 38mm tires, I googled and the consensus was I was ok putting up to 51mm tires on a 17mm inner rim.
I would post pictures but I don't want to ruin anyone's lunch. Needless to say my fingers are torn up trying to get the tires to seat evenly on the manufacturers line with the rim. It was at least a half hour of pulling in various spots and tearing up the inner pads on my fingers in two places. I should have used soap but just used brute force.
I've come to the conclusion every tire and rim situation is so unique you can never count a review saying "Easy to mount" or "Hard to mount".
Likes For EDP:
#2
Mother Nature's Son
Join Date: Mar 2016
Location: Sussex County, Delaware
Posts: 3,123
Bikes: 2014 Orbea Avant MD30, 2004 Airborne Zeppelin TI, 2003 Lemond Poprad, 2001 Lemond Tourmalet, 2014? Soma Smoothie
Mentioned: 15 Post(s)
Tagged: 0 Thread(s)
Quoted: 854 Post(s)
Liked 1,447 Times
in
824 Posts
Quite frustrating at times. I gave up on the brute force, significant arthritis in my hands. I now gladly use tires levers and a bead jack. There are tires I can still mount and remove with just my hands, but more often than not, I go right to the tools. Some rim/tire matches are still somewhat difficult, most are easier after being mounted on the rims for a bit of time.
#3
Senior Member
Join Date: Feb 2007
Posts: 1,459
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 631 Post(s)
Likes: 0
Liked 406 Times
in
278 Posts
I just put a Schwalbe 26" X 2.125 tire on my Velocity Psycho rim. I used the Crank Brothers Speedier Tire lever to remove the old tire and install the new one. The fun part was using my new mini pump. It took 160 stomps to inflate the tire to 35 psi. My Taticco took more than 300 strokes to fill a 26" X 2" tire last year. I am getting older and my Road Morph aggravated my sciatic nerve a couple of years ago. The Taticco was better but it was still not very pleasant. The new mini foot pump didn't aggravate any thing so it's a keeper.
Likes For Rick:
#4
Senior Member
Join Date: Feb 2022
Location: GMT-5
Posts: 964
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 563 Post(s)
Liked 420 Times
in
278 Posts
Needless to say my fingers are torn up trying to get the tires to seat evenly on the manufacturers line with the rim. It was at least a half hour of pulling in various spots and tearing up the inner pads on my fingers in two places. I should have used soap but just used brute force.
Likes For soyabean:
#5
Senior Member
Join Date: Mar 2021
Posts: 2,009
Mentioned: 25 Post(s)
Tagged: 0 Thread(s)
Quoted: 2730 Post(s)
Liked 488 Times
in
353 Posts
When I get one side seated and am struggling to finish seating the other side, I put the unseated part at 6 o clock and then grab the tire at 12 o clock and pull at it, working my way down to 12 o clock on either side trying to get any slack down there. I repeat this 3 or so times, it makes the final step much easier.
Likes For LarrySellerz:
#6
Senior Member
Join Date: Dec 2004
Posts: 1,111
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 580 Post(s)
Liked 668 Times
in
395 Posts
Some rims are easier, some tires are easier.
Then there are some rim/tire combos that make you wonder if you should ever change a tire again.
20" Marathon Plus were monsters to mount years ago (newer ones are easier and I don't know why)
Technique improves over time, and good tools like steel core tire levers also helps.
Me personal record is mounting and inflating 65 tires in a day.
(walked around like a T-Rex for hours afterward)
Then there are some rim/tire combos that make you wonder if you should ever change a tire again.
20" Marathon Plus were monsters to mount years ago (newer ones are easier and I don't know why)
Technique improves over time, and good tools like steel core tire levers also helps.
Me personal record is mounting and inflating 65 tires in a day.
(walked around like a T-Rex for hours afterward)
Likes For CrimsonEclipse:
#7
Junior Member
Join Date: May 2023
Posts: 162
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 63 Post(s)
Likes: 0
Liked 49 Times
in
37 Posts
Not only does tire mounting differ each time, I find that squeezing a bike into a car, it goes in differently each time, and also pulling the bike out is different too. And unlike tires, there are no special tools (like the Crank Bros tool aforementioned) for squeezing a bike into a car.
#8
I'm good to go!
Join Date: Jul 2017
Location: Mississippi
Posts: 15,094
Bikes: Tarmac Disc Comp Di2 - 2020
Mentioned: 51 Post(s)
Tagged: 0 Thread(s)
Quoted: 6255 Post(s)
Liked 4,857 Times
in
3,347 Posts
Was the first side of the tire easy to get on? The second side should be almost as easy to put on. You just have to get the bead of the first side and inner tube out of the spoke channel. That's the part that isn't always so easy and is what usually makes putting on the second side difficult. If you have already put a little air in the inner tube, then this is the time you need to let it all out.
#9
Junior Member
I visibly remember chunking some rubber off the bead of tubeless DH tires on my mountain bikes. Now I have lube for the beads when I do motorcycle tires and i needed I don't mind using it on a stubborn bike tire.
#10
Senior Member
Join Date: Dec 2020
Location: Wake Forest, NC
Posts: 5,860
Bikes: 1989 Cinelli Supercorsa
Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 3560 Post(s)
Liked 2,978 Times
in
1,801 Posts
Never had a tire/rim combo that I ever needed anything but my hands to install. They say some tires are more difficult today, but that’s nothing I’ve come across.
Likes For smd4:
#11
Senior Member
Join Date: Jul 2014
Location: socal
Posts: 4,288
Mentioned: 9 Post(s)
Tagged: 0 Thread(s)
Quoted: 889 Post(s)
Liked 840 Times
in
634 Posts
As above, some combos don't mix well. The real problem is if one discovers it on the trail far from home. I've encountered this while in the wild,
#12
Junior Member
[QUOTE=Me personal record is mounting and inflating 65 tires in a day.
(walked around like a T-Rex for hours afterward)[/QUOTE]
Help - I just blew coffee out my nose!
(walked around like a T-Rex for hours afterward)[/QUOTE]
Help - I just blew coffee out my nose!
#13
Full Member
Join Date: Jul 2018
Posts: 396
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 141 Post(s)
Liked 152 Times
in
98 Posts
I once purchased Continental 5000's that I could not get mounted. Took it to a bike shop and let them handle it.
Also, per the advice from this forum, I purchased a bead jack but have yet to use it.
Also, per the advice from this forum, I purchased a bead jack but have yet to use it.
#14
Senior Member
I just finished putting 4 new tires on 2 bikes for the 2024 season.
I mounted a 2.4 inch Maxxis Race Rekon and 2.4 inch Maxxis Forekaster onto a Trek Roscoe 8 that had OEM Trek XR4 Team Issue 2.6 inch tires. Those tires were fine but I'm making the Roscoe more of a X-Country bike. Both were surprisingly easy with just a smidge of tire lever at the end. I didn't even have a charge pump or air compressor- I just used a Joe Blow floor pump and both tubeless tires seated with a normal tire pumping pace.
Next I put 2 Schwalbe G One Overland 700x45 tires on a Flatbike Gravel bike with Shimano WH-RX010 rims. This bike is a tube set up and despite the inner rim being 17mm and Shimano suggesting a maximum of 38mm tires, I googled and the consensus was I was ok putting up to 51mm tires on a 17mm inner rim.
I would post pictures but I don't want to ruin anyone's lunch. Needless to say my fingers are torn up trying to get the tires to seat evenly on the manufacturers line with the rim. It was at least a half hour of pulling in various spots and tearing up the inner pads on my fingers in two places. I should have used soap but just used brute force.
I've come to the conclusion every tire and rim situation is so unique you can never count a review saying "Easy to mount" or "Hard to mount".
I mounted a 2.4 inch Maxxis Race Rekon and 2.4 inch Maxxis Forekaster onto a Trek Roscoe 8 that had OEM Trek XR4 Team Issue 2.6 inch tires. Those tires were fine but I'm making the Roscoe more of a X-Country bike. Both were surprisingly easy with just a smidge of tire lever at the end. I didn't even have a charge pump or air compressor- I just used a Joe Blow floor pump and both tubeless tires seated with a normal tire pumping pace.
Next I put 2 Schwalbe G One Overland 700x45 tires on a Flatbike Gravel bike with Shimano WH-RX010 rims. This bike is a tube set up and despite the inner rim being 17mm and Shimano suggesting a maximum of 38mm tires, I googled and the consensus was I was ok putting up to 51mm tires on a 17mm inner rim.
I would post pictures but I don't want to ruin anyone's lunch. Needless to say my fingers are torn up trying to get the tires to seat evenly on the manufacturers line with the rim. It was at least a half hour of pulling in various spots and tearing up the inner pads on my fingers in two places. I should have used soap but just used brute force.
I've come to the conclusion every tire and rim situation is so unique you can never count a review saying "Easy to mount" or "Hard to mount".
#15
Senior Member
It's difficult because hookless came onto the scene, and as a result everybody had to make their tires tighter than a baby's ass, to avoid being sued into bankruptcy from tires coming off.
#16
I'm good to go!
Join Date: Jul 2017
Location: Mississippi
Posts: 15,094
Bikes: Tarmac Disc Comp Di2 - 2020
Mentioned: 51 Post(s)
Tagged: 0 Thread(s)
Quoted: 6255 Post(s)
Liked 4,857 Times
in
3,347 Posts
I highly doubt that. People have been complaining about hard to mount tire before smooth bead rims started making a comeback. Smooth bead rims have actually been around since vintage days. But they disappeared or became obscure for 20 maybe 30 years.
#17
Senior Member
Past complaints don't mean jack sh*t.
Likes For Yan:
#18
I'm good to go!
Join Date: Jul 2017
Location: Mississippi
Posts: 15,094
Bikes: Tarmac Disc Comp Di2 - 2020
Mentioned: 51 Post(s)
Tagged: 0 Thread(s)
Quoted: 6255 Post(s)
Liked 4,857 Times
in
3,347 Posts
Likes For alcjphil:
#20
Full Member
No tire is hard to mount, if you know the technique. You will know if a tire is easy to mount or hard to mount, when you are replacing a worn-out tire with a new tire. When you meet with a hard to mount tire, practice it 2 or 3 times (i.e., remove the tire and mount it again 2 or 3 times) before you go on your first bike ride with the new tire, and familiarize yourself with the technique.
Get yourself a Kool-Stop tire bead jack, and save yourself some headache. This tool is worth its price and will not only help you to save your fingers but also to avoid pinching the tube between the tire and the rim and to avoid pinch flats.
https://www.renehersecycles.com/shop...ire-bead-jack/
I use the technique in this video 👇. Instead of the wall, I also use a tree or a pole, when I am on the road and face with a flat, and don't find a wall.
Get yourself a Kool-Stop tire bead jack, and save yourself some headache. This tool is worth its price and will not only help you to save your fingers but also to avoid pinching the tube between the tire and the rim and to avoid pinch flats.
https://www.renehersecycles.com/shop...ire-bead-jack/
I use the technique in this video 👇. Instead of the wall, I also use a tree or a pole, when I am on the road and face with a flat, and don't find a wall.