9 spd brifter with 8spd cassette?
#1
Alfredo Contador
Thread Starter
Join Date: Jan 2010
Location: Where everybody knows my name
Posts: 431
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
9 spd brifter with 8spd cassette?
So far Uncle Google seems to indicate mostly not possible. Just wondering if folks here would concur.
Am hoping to get by with the 8 cogs rear until time to replace them. Thoughts?
Am hoping to get by with the 8 cogs rear until time to replace them. Thoughts?
#3
Senior Member
Join Date: Feb 2005
Location: Oklahoma
Posts: 9,438
Bikes: Trek 5500, Colnago C-50
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4 Post(s)
Likes: 0
Liked 7 Times
in
6 Posts
If Shimano all you need to be 9-speed is the 9-speed shifters, cassette, and chain (unless your 8-speed is Dura-Ace).
What component group do you have?
What component group do you have?
#4
Engineer
Join Date: May 2010
Location: Bucharest, Romania, Europe
Posts: 591
Bikes: 1989 Krapf (with Dura-ace) road bike, 1973 Sputnik (made by XB3) road bike , 1961 Peugeot fixed gear, 2010 Trek 4400
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 38 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
It can be done but only if the 8speed cassette is obtained by removing one gear from a 9speed cassette, otherwise no
What happens with 8speed dura-ace? I happen to have 7400 8sp Dura-ace and I am curious..
What happens with 8speed dura-ace? I happen to have 7400 8sp Dura-ace and I am curious..
#6
Senior Member
Join Date: Apr 2006
Location: Orange County CA
Posts: 963
Bikes: Surly CC, Raleigh Team Pro, Specialized Rockhopper with an xtracycle
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
7400 dura ace apparently has a different pull ratio than other shimano rear derailleurs.
To answer the OP, I was able to do the following:
Campy 9 speed ergo, shimano rear, shimano/sram 8 speed cassette.
I was even able to get the ergo to work with shimano 9 speed cassette but that was more finicky.
Have a look at this article. It has pull ratios and spacing for different combinations.
https://www.ctc.org.uk/DesktopDefault.aspx?TabID=3946
Also, you might be able to use a jtek or something like that.
To answer the OP, I was able to do the following:
Campy 9 speed ergo, shimano rear, shimano/sram 8 speed cassette.
I was even able to get the ergo to work with shimano 9 speed cassette but that was more finicky.
Have a look at this article. It has pull ratios and spacing for different combinations.
https://www.ctc.org.uk/DesktopDefault.aspx?TabID=3946
Also, you might be able to use a jtek or something like that.
#7
Senior Member
Join Date: Aug 2005
Location: Pittsburgh, PA
Posts: 33,656
Bikes: '96 Litespeed Catalyst, '05 Litespeed Firenze, '06 Litespeed Tuscany, '20 Surly Midnight Special, All are 3x10. It is hilly around here!
Mentioned: 39 Post(s)
Tagged: 0 Thread(s)
Quoted: 2026 Post(s)
Likes: 0
Liked 1,096 Times
in
742 Posts
The cassette and chain are far cheaper than the brifters so why not go 9-speed all the way? You don't even have to change your freehub.
#8
Member
Join Date: May 2010
Location: Washington DC
Posts: 44
Bikes: 2010 Jamis Beatnik, 1987 Cannondale ST800, 1987 Cannondale Black Lightning
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
but i thought you could use 8 speed sora brifters to convert old school downtube shifting bikes that are 7, 6 or even 5 speed cassettes, you just have 'ghost' shifts?
#10
Senior Member
Join Date: Apr 2010
Location: Mountain View, CA USA and Golden, CO USA
Posts: 6,341
Bikes: 97 Litespeed, 50-39-30x13-26 10 cogs, Campagnolo Ultrashift, retroreflective rims on SON28/PowerTap hubs
Mentioned: 9 Post(s)
Tagged: 0 Thread(s)
Quoted: 550 Post(s)
Liked 325 Times
in
226 Posts
Jtek sells ratio converters that will do the trick but one will cost as much as a new cassette shipped here from the UK.
#11
Senior Member
Join Date: Aug 2005
Location: Pittsburgh, PA
Posts: 33,656
Bikes: '96 Litespeed Catalyst, '05 Litespeed Firenze, '06 Litespeed Tuscany, '20 Surly Midnight Special, All are 3x10. It is hilly around here!
Mentioned: 39 Post(s)
Tagged: 0 Thread(s)
Quoted: 2026 Post(s)
Likes: 0
Liked 1,096 Times
in
742 Posts
Within modern cog counts, 8 and above, there are adapters from Jtek that will allow a reasonable mis-match of cog spacing and brifters but there is no universal brifter.
#12
Senior Member
Join Date: Apr 2006
Location: Orange County CA
Posts: 963
Bikes: Surly CC, Raleigh Team Pro, Specialized Rockhopper with an xtracycle
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
what kind of cassette is that 8 speed? I have a 9 speed that I might be willing to trade. It is 11-25 sram. I'll have to check the model number. PM me.
#13
Senior Member
Join Date: Apr 2004
Location: Suburban Boston
Posts: 473
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
If your 7400 DA are the brifters they will require the DA rear derailluer to shift the 8 spd cassette. BUT, I used the 8 spd DA brifters on a 9 spd cassette for a year without any issues.
#14
Senior Member
Join Date: Feb 2005
Location: Oklahoma
Posts: 9,438
Bikes: Trek 5500, Colnago C-50
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4 Post(s)
Likes: 0
Liked 7 Times
in
6 Posts
Since this thread has already gone well beyond answering the original question, I'll add to the confusion.
It is possible to shift a Shimano 8-speed cassette with a Shimano 9-speed shifter if you use an 8-speed Dura-Ace rear derailleur. As it turns out, the Dura Ace 8-speed shifter cable pull is the same as the cable pull of all Shimano 9-speed shifters. The reason this works is that the 8-speed D-A rear derailleur actuation ratio is different and when combined with a 9-speed shifter the travel for each click matches the 8-speed cog spacing "perfectly".
Take a look at this chart, scroll down to Shimano mech: https://www.ctc.org.uk/DesktopDefault.aspx?TabID=3946
It is possible to shift a Shimano 8-speed cassette with a Shimano 9-speed shifter if you use an 8-speed Dura-Ace rear derailleur. As it turns out, the Dura Ace 8-speed shifter cable pull is the same as the cable pull of all Shimano 9-speed shifters. The reason this works is that the 8-speed D-A rear derailleur actuation ratio is different and when combined with a 9-speed shifter the travel for each click matches the 8-speed cog spacing "perfectly".
Take a look at this chart, scroll down to Shimano mech: https://www.ctc.org.uk/DesktopDefault.aspx?TabID=3946
#15
Alfredo Contador
Thread Starter
Join Date: Jan 2010
Location: Where everybody knows my name
Posts: 431
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
My 8spd is a HG50 from Shimano.
Al1943
Since this thread has already gone well beyond answering the original question, I'll add to the confusion.
It is possible to shift a Shimano 8-speed cassette with a Shimano 9-speed shifter if you use an 8-speed Dura-Ace rear derailleur. As it turns out, the Dura Ace 8-speed shifter cable pull is the same as the cable pull of all Shimano 9-speed shifters. The reason this works is that the 8-speed D-A rear derailleur actuation ratio is different and when combined with a 9-speed shifter the travel for each click matches the 8-speed cog spacing "perfectly".
Take a look at this chart, scroll down to Shimano mech: https://www.ctc.org.uk/DesktopDefault.aspx?TabID=3946
Since this thread has already gone well beyond answering the original question, I'll add to the confusion.
It is possible to shift a Shimano 8-speed cassette with a Shimano 9-speed shifter if you use an 8-speed Dura-Ace rear derailleur. As it turns out, the Dura Ace 8-speed shifter cable pull is the same as the cable pull of all Shimano 9-speed shifters. The reason this works is that the 8-speed D-A rear derailleur actuation ratio is different and when combined with a 9-speed shifter the travel for each click matches the 8-speed cog spacing "perfectly".
Take a look at this chart, scroll down to Shimano mech: https://www.ctc.org.uk/DesktopDefault.aspx?TabID=3946
I have an Ultegra FD too. My bike is a smorgasbord of Shimano parts. All I need is to throw in some 105 brakes and it will be a rolling parts bin for Shimano. Maybe get Yumeya Ti-Nitride chain too?
Last edited by |3iker; 10-06-10 at 09:08 AM.
#16
Alfredo Contador
Thread Starter
Join Date: Jan 2010
Location: Where everybody knows my name
Posts: 431
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
According to this website https://www.ctc.org.uk/DesktopDefault.aspx?TabID=3946
using the Hubbub method it may work. Or am I understanding it incorrectly?
using the Hubbub method it may work. Or am I understanding it incorrectly?
#17
Banned
One of the Jtec pulleys fix that?
I stay with a friction shifter scheme, myself, so bypass these issues ..
I stay with a friction shifter scheme, myself, so bypass these issues ..
#18
Senior Member
Join Date: May 2005
Posts: 195
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
Sheldon Brown has an example of how to attach the der. cable in this situation. I had exactly the same problem but I could not make this work in my case. You might have better luck. Scroll down to the paragraph near the bottom of the page to "Alternate Cable Routing"
https://www.sheldonbrown.com/derailer-adjustment.html
https://www.sheldonbrown.com/derailer-adjustment.html
#19
Engineer
Join Date: May 2010
Location: Bucharest, Romania, Europe
Posts: 591
Bikes: 1989 Krapf (with Dura-ace) road bike, 1973 Sputnik (made by XB3) road bike , 1961 Peugeot fixed gear, 2010 Trek 4400
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 38 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
I have no intend to go to brifters, I just like DT shifters
#20
Banned.
Join Date: Aug 2010
Posts: 732
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Sheldon Brown has an example of how to attach the der. cable in this situation. I had exactly the same problem but I could not make this work in my case. You might have better luck. Scroll down to the paragraph near the bottom of the page to "Alternate Cable Routing"
https://www.sheldonbrown.com/derailer-adjustment.html
https://www.sheldonbrown.com/derailer-adjustment.html
#21
Senior Member
Join Date: Dec 2009
Location: Melbourne, Oz
Posts: 9,547
Bikes: https://weightweenies.starbike.com/forum/viewtopic.php?f=10&t=152015&p=1404231
Mentioned: 15 Post(s)
Tagged: 0 Thread(s)
Quoted: 1529 Post(s)
Liked 718 Times
in
510 Posts
Which sucks. You should be able to buy replacement indexing bits, IMO... I'd like to see someone try it and clean up the competition in the aftermarket scene...
Also, it occurs to me that it should be eminently possible to convert Ergolevers to friction shift.
Also, it occurs to me that it should be eminently possible to convert Ergolevers to friction shift.
#22
Engineer
Join Date: May 2010
Location: Bucharest, Romania, Europe
Posts: 591
Bikes: 1989 Krapf (with Dura-ace) road bike, 1973 Sputnik (made by XB3) road bike , 1961 Peugeot fixed gear, 2010 Trek 4400
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 38 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
No can do! (friction in brifter) because the lever has to return after shift not to stay in that position.
The only thing I can picture is a thumb shifter (friction) on the upper part of the hoods of the brifter. That could work.
The only thing I can picture is a thumb shifter (friction) on the upper part of the hoods of the brifter. That could work.
#23
Senior Member
Join Date: Mar 2002
Location: NJ
Posts: 3,084
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4 Post(s)
Likes: 0
Liked 5 Times
in
4 Posts
Thanks, I was just curious, I have DA7400 DT shifters (indexed rear, friction front) , DA7400 cassette, DA7400 rear derailleur, in fact it's the whole set (hubs, front mech, headset, cranks, chainring, BB, pedals, calipers, brake levers, brake pads, even the seatpost ) - of course not all of them are 7400, but 74xx series like 7400, 7401, 7402, 7403
I have no intend to go to brifters, I just like DT shifters
I have no intend to go to brifters, I just like DT shifters
=rob
#24
cycles per second
Join Date: Oct 2003
Location: Minnesota
Posts: 1,930
Bikes: Early 1980's Ishiwata 022 steel sport/touring, 1986 Vitus 979, 1988 DiamondBack Apex, 1997 Softride PowerWing 700, 2001 Trek OCLV 110
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 44 Post(s)
Liked 71 Times
in
48 Posts
Two possibilities:
1) If your rear derailer is not Dura-Ace 7400 (or 7401 or 7402), you could try this alternate cable attachment which causes the rear derailer to move about 10% further per shift - https://www.sheldonbrown.com/dura-ace.html#indexing
2) If your rear derailer is Dura-Ace 7400 (or 7401 or 7402), it will already shift 8-speed spacing with Shimano 9-speed shifters.
1) If your rear derailer is not Dura-Ace 7400 (or 7401 or 7402), you could try this alternate cable attachment which causes the rear derailer to move about 10% further per shift - https://www.sheldonbrown.com/dura-ace.html#indexing
2) If your rear derailer is Dura-Ace 7400 (or 7401 or 7402), it will already shift 8-speed spacing with Shimano 9-speed shifters.
#25
Alfredo Contador
Thread Starter
Join Date: Jan 2010
Location: Where everybody knows my name
Posts: 431
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Just an update..... I applied the "alternate cable routing" method and managed to make it work! 9-spd shifter on a 8-spd cassette using a 10-speed RD!!! How's that for an unholy alliance?!