Planning if my chain breaks
#1
Full Member
Thread Starter
Planning if my chain breaks
I just installed a BBSHD motor on my bike, and it is a lot more powerful than I expected. I really like this increased power, but I'm worried about breaking my chain. If I break it during a commute, I want to be prepared.
I have this tool already, although it is a little large for a small tool kit.
I understand I need some replacement links (?). Can someone tell me what these are and suggest one that might work?
I'd like to put these items in my repair kit to be ready. Or should I just carry a spare chain?
I have this tool already, although it is a little large for a small tool kit.
I understand I need some replacement links (?). Can someone tell me what these are and suggest one that might work?
I'd like to put these items in my repair kit to be ready. Or should I just carry a spare chain?
#2
Senior Member
Join Date: Jul 2014
Location: socal
Posts: 4,265
Mentioned: 9 Post(s)
Tagged: 0 Thread(s)
Quoted: 883 Post(s)
Liked 823 Times
in
622 Posts
It's possible to repair a broken chain with a chain breaker, but much easier to just use a quick link. Just procure one for your chain (9, 10 or whatever speed it is). Also, many small multi-tools have a chain breaker in addition to other tools.
#3
Senior Member
Join Date: Nov 2014
Location: Eugene, Oregon, USA
Posts: 27,547
Mentioned: 217 Post(s)
Tagged: 0 Thread(s)
Quoted: 18378 Post(s)
Liked 4,512 Times
in
3,354 Posts
I carry a chain tool with me most of the time. Some of the bike repair hex wrench sets also include a mini chain tool. It has come in handy a few times. The alternative could be a very long walk.
If you have 8 speed or less, and perhaps 9 speed, then you can just push out a pin, and shorten the chain and re-install. Be careful of cross-chaining if you field shorten the chain. Check for a worn chain if you're breaking chains, and perhaps replace anyway.
10s or 11s really should get a special link pin, or quick connect, but do what you need in a pinch.
If you have 8 speed or less, and perhaps 9 speed, then you can just push out a pin, and shorten the chain and re-install. Be careful of cross-chaining if you field shorten the chain. Check for a worn chain if you're breaking chains, and perhaps replace anyway.
10s or 11s really should get a special link pin, or quick connect, but do what you need in a pinch.
#4
Full Member
Thread Starter
What does the bike speed have to do with the type of chain? If it helps, I'm using this on a Cannondale Trail 7.
#5
Senior Member
Join Date: Jul 2015
Location: Chicago Suburbs
Posts: 1,406
Bikes: GT Transeo & a half dozen ebike conversions.
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 340 Post(s)
Liked 275 Times
in
192 Posts
When you push out a pin, it's not easy to push it back in so that the link doesn't bind. And if it binds, it tends to wrap around the small gears in the derailleur and cause the chain to slip. When this happens on a BBS motor, you really feel it. If you fiddle with the tool and do it by feel, you might get the link to work freely. Not easy out in the field or even at home.
The bikes with 8-10 speeds use thinner chains where I guess it's even harder to push a pin in correctly.
When I asked about this in the bike mechanics forum, they told me to use master links. KMC, the chain maker, also tells you to use master links. Anyway, they're not expensive and work nice, except you might need a link pliers, and you still need a chain breaker too.
The bikes with 8-10 speeds use thinner chains where I guess it's even harder to push a pin in correctly.
When I asked about this in the bike mechanics forum, they told me to use master links. KMC, the chain maker, also tells you to use master links. Anyway, they're not expensive and work nice, except you might need a link pliers, and you still need a chain breaker too.
#6
Senior Member
Join Date: Feb 2014
Location: Pasadena, CA
Posts: 4,848
Bikes: Schwinn Varsity
Mentioned: 22 Post(s)
Tagged: 0 Thread(s)
Quoted: 1931 Post(s)
Liked 742 Times
in
422 Posts
Is your bike 9 speed?
Maybe use an ebike chain to get it to last longer:
https://www.universalcycles.com/shop...99&category=59
Maybe use an ebike chain to get it to last longer:
https://www.universalcycles.com/shop...99&category=59
#8
Full Member
Thread Starter
Excellent information, thanks!
#9
Senior Member
Join Date: Jul 2010
Location: Michigan
Posts: 4,863
Bikes: too many of all kinds
Mentioned: 35 Post(s)
Tagged: 0 Thread(s)
Quoted: 1147 Post(s)
Liked 415 Times
in
335 Posts
When you push out a pin, it's not easy to push it back in so that the link doesn't bind. And if it binds, it tends to wrap around the small gears in the derailleur and cause the chain to slip. When this happens on a BBS motor, you really feel it. If you fiddle with the tool and do it by feel, you might get the link to work freely. Not easy out in the field or even at home.
The bikes with 8-10 speeds use thinner chains where I guess it's even harder to push a pin in correctly.
When I asked about this in the bike mechanics forum, they told me to use master links. KMC, the chain maker, also tells you to use master links. Anyway, they're not expensive and work nice, except you might need a link pliers, and you still need a chain breaker too.
The bikes with 8-10 speeds use thinner chains where I guess it's even harder to push a pin in correctly.
When I asked about this in the bike mechanics forum, they told me to use master links. KMC, the chain maker, also tells you to use master links. Anyway, they're not expensive and work nice, except you might need a link pliers, and you still need a chain breaker too.
Answer: The way to avoid that is to use a
Park Tool CT-5 (or similar). it has a second shelf that allows you to easily back the pin out a little to loosen the link (and not compress the link like the bottom shelf).
There is a short mention of this in the video (at 24 seconds):
The tool pictured above has only one shelf, and may not do this effectively.
Note this tool has two shelves:
Park Tool CT-5