Has anyone successfully uncracked a frame?
#1
Senior Member
Thread Starter
Has anyone successfully uncracked a frame?
We see it all the time, steel cracked, Ti cracked, alu cracked, carbon cracked... they all actually crack sooner or later.
But has anyone actually managed to repair any of their cracked frames no matter material??
How did it turn out? How much did it cost you? Did the repair last?
But has anyone actually managed to repair any of their cracked frames no matter material??
How did it turn out? How much did it cost you? Did the repair last?
#2
Senior Member
Join Date: Oct 2014
Location: Portland, OR
Posts: 12,905
Bikes: (2) ti TiCycles, 2007 w/ triple and 2011 fixed, 1979 Peter Mooney, ~1983 Trek 420 now fixed and ~1973 Raleigh Carlton Competition gravel grinder
Mentioned: 129 Post(s)
Tagged: 0 Thread(s)
Quoted: 4806 Post(s)
Liked 3,928 Times
in
2,553 Posts
I have an old Trek that cracked across the seatstay cap lettering on both sides. A local framebuilder repaired them; I believe by heating and lifting off the caps, then adding a lot of braze to the stay end and replacing the caps. The offending letter got filled in on the worst crack.
He also repaired the cracks in the tubes of an even older Raleigh Competition that apparently went straight from jigging and tack-brazing to paint. Didn't ask him the details of how he did the repairs. (He did say that the paint job was excellent; that the painter did a really good job of flowing the paint under the lugs and that the paint was probably holding the bike together!)
Broke a Peugeot UO-8 chainstay years ago behind the bridge. I was a boatbuilder at the time and had a local rigger weld it up.
I doubt the Peugeot repair would have lasted forever. I'll never know. The bike died a violent death two years later. I full expect the other repairs to outlive me.
Ben
He also repaired the cracks in the tubes of an even older Raleigh Competition that apparently went straight from jigging and tack-brazing to paint. Didn't ask him the details of how he did the repairs. (He did say that the paint job was excellent; that the painter did a really good job of flowing the paint under the lugs and that the paint was probably holding the bike together!)
Broke a Peugeot UO-8 chainstay years ago behind the bridge. I was a boatbuilder at the time and had a local rigger weld it up.
I doubt the Peugeot repair would have lasted forever. I'll never know. The bike died a violent death two years later. I full expect the other repairs to outlive me.
Ben
#3
Senior Member
Thread Starter
#5
On Your Left
Join Date: Nov 2011
Location: Long Island, New York, USA
Posts: 8,373
Bikes: Trek Emonda SLR, Sram eTap, Zipp 303
Mentioned: 34 Post(s)
Tagged: 0 Thread(s)
Quoted: 3004 Post(s)
Liked 2,433 Times
in
1,187 Posts
I damaged the carbon on the chainstay. Sent it to Calfee and $350 later its as good as new.
#6
Senior Member
Join Date: Mar 2010
Location: Seattle, WA
Posts: 23,208
Mentioned: 89 Post(s)
Tagged: 0 Thread(s)
Quoted: 18883 Post(s)
Liked 10,646 Times
in
6,054 Posts
Built a wormhole and went back to a time when the bike wasn't cracked. Lasted until it cracked again.
Likes For Seattle Forrest:
#7
Senior Member
Join Date: Jan 2010
Location: TC, MN
Posts: 39,520
Bikes: R3 Disc, Haanjo
Mentioned: 354 Post(s)
Tagged: 1 Thread(s)
Quoted: 20810 Post(s)
Liked 9,456 Times
in
4,672 Posts