Go Back  Bike Forums > Bike Forums > General Cycling Discussion
Reload this Page >

Chain and Cassette Life?

Notices
General Cycling Discussion Have a cycling related question or comment that doesn't fit in one of the other specialty forums? Drop on in and post in here! When possible, please select the forum above that most fits your post!

Chain and Cassette Life?

Old 06-24-20, 10:21 PM
  #1  
alloo
Full Member
Thread Starter
 
alloo's Avatar
 
Join Date: Apr 2019
Location: Albuquerque, NM
Posts: 490

Bikes: 2022 Priority Coast, 2022 Priority Current

Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 175 Post(s)
Liked 137 Times in 99 Posts
Chain and Cassette Life?

How long do your chains and casettes last on your bicycle? With regular maintenance vs w/o maintainance? Miles? Time? I've had two bikes that have needed new chains after about 800 miles is this normal?
alloo is offline  
Old 06-25-20, 01:43 AM
  #2  
jgwilliams
Senior Member
 
jgwilliams's Avatar
 
Join Date: Aug 2004
Location: Surrey, UK
Posts: 866

Bikes: Dolan Tuono 105 Di2, custom built 653 and 531 bikes with frames by Barry Witcomb, Sonder Dial XT mountain bike and a Brompton folding bike.

Mentioned: 6 Post(s)
Tagged: 0 Thread(s)
Quoted: 297 Post(s)
Liked 139 Times in 99 Posts
There's no straightforward answer to this. My previous regular commute had a Campy 9-speed groupset and I found that the chain lasted me about 10,000 miles. My new commute came with SRAM Force 11 groupset but the cheapskate manufacturers put on bottom of the range PC 1110 chain and cassette. That chain only lasted 2,000 miles. I replaced with the 1170 chain which has so far done another 2,000 miles with no sign of wear. I've never had to replace a cassette because of wear.
jgwilliams is offline  
Likes For jgwilliams:
Old 06-25-20, 02:36 AM
  #3  
guy153
Senior Member
 
Join Date: Dec 2019
Posts: 950
Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 321 Post(s)
Liked 261 Times in 212 Posts
Originally Posted by alloo
How long do your chains and casettes last on your bicycle? With regular maintenance vs w/o maintainance? Miles? Time? I've had two bikes that have needed new chains after about 800 miles is this normal?
They usually last a bit longer than that. I get a few thousand km out of a chain and a cassette lasts three or four chains or so. I don't do a great deal of maintenance (each chain gets properly cleaned maybe two or three times in its life if it's lucky).
guy153 is offline  
Likes For guy153:
Old 06-25-20, 04:01 AM
  #4  
Witterings
Senior Member
 
Join Date: Jul 2010
Location: The Witterings, West Sussex
Posts: 1,066
Mentioned: 8 Post(s)
Tagged: 0 Thread(s)
Quoted: 569 Post(s)
Liked 37 Times in 29 Posts
Where are you riding ... is it dusty, gritty, sandy, muddy ..... I've only just learnt how much crap you can pick up in the summer with too much wet lube it was literally caked on the chain, cassette and jockey wheels and I'm sure it'd shorten it's life dramatically if I hadn't of realised and cleaned it off.

Some people set a regime of using the 3 chains ... run the 1st 2 until they've stretched to 0.5 and the 3rd until it's stretched to 0.75 and then go back and use the 1st two until they hit 0.75 .... supposedly this gives you the max usage out of your chains and cassette.
Witterings is offline  
Likes For Witterings:
Old 06-25-20, 04:01 AM
  #5  
datlas 
Should Be More Popular
 
datlas's Avatar
 
Join Date: Dec 2007
Location: Malvern, PA (20 miles West of Philly)
Posts: 42,956

Bikes: 1986 Alpine (steel road bike), 2009 Ti Habenero, 2013 Specialized Roubaix

Mentioned: 560 Post(s)
Tagged: 2 Thread(s)
Quoted: 22512 Post(s)
Liked 8,840 Times in 4,113 Posts
Define “need new chain.”

I get 3000 miles/chain with not much maintenance, replace when elongated by 0.75% or so. Cassettes last longer, around 10K miles.
__________________
Originally Posted by rjones28
Addiction is all about class.
datlas is offline  
Likes For datlas:
Old 06-25-20, 04:09 AM
  #6  
jpescatore
Senior Member
 
Join Date: Oct 2017
Location: Ashton, MD USA
Posts: 1,296

Bikes: Trek Domane SL6 Disc, Jamis Renegade

Mentioned: 6 Post(s)
Tagged: 0 Thread(s)
Quoted: 363 Post(s)
Liked 304 Times in 217 Posts
800 miles is definitely lower than normal in my experience, unless you are constantly riding in dirt/grit and never cleaning it off! I normally closer to 3,000 miles on my road bike, longer on my older 9 speed bike.

Some things that make chains last longer:
  • Make sure your derailleurs and derailleur hanger are all tuned/indexed/aligned properly.
  • Make sure you lubricate the chain regularly - and clean it (and the cassette/chain rings) each type you lube it, vs. just adding more lube.
  • Avoid cross chaining - avoid big ring in front, small in back or small ring in front, big cog in back combos. The straighter the chain stays from chain ring to cassette the longer it will last.
  • After each ride, wipe the chain off to remove surface grit - only takes a second
Since you've had the problem across 2 different bikes, probably not the first item.
jpescatore is offline  
Likes For jpescatore:
Old 06-25-20, 04:39 AM
  #7  
CAT7RDR
Senior Member
 
Join Date: May 2017
Location: Hacienda Hgts
Posts: 2,083

Bikes: 1999 Schwinn Peloton Ultegra 10, Kestrel RT-1000 Ultegra, Trek Marlin 6 Deore 29'er

Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 811 Post(s)
Liked 1,946 Times in 936 Posts
^^^^^^FIFY
Avoid cross chaining - avoid big ring in front, big in back or small ring in front, small cog in back combos. The straighter the chain stays from chain ring to cassette the longer it will last.
CAT7RDR is online now  
Likes For CAT7RDR:
Old 06-25-20, 07:40 AM
  #8  
Koyote
Senior Member
 
Join Date: Sep 2017
Posts: 7,764
Mentioned: 37 Post(s)
Tagged: 0 Thread(s)
Quoted: 6882 Post(s)
Liked 10,871 Times in 4,636 Posts
OP needs to provide more info:
-What sort of drivetrain? 11sp doesn't last as long as 7sp.
-Ridden in which sort of conditions? Riding in mud and dirt may shorten life of chains and cassettes by more than half.
-What sort of maintenance is being done?
-etc.
Koyote is online now  
Likes For Koyote:
Old 06-25-20, 07:57 AM
  #9  
xroadcharlie
Senior Member
 
Join Date: Apr 2019
Location: Windsor Ontario, Canada
Posts: 531

Bikes: 2018 Giant Sedona

Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 179 Post(s)
Liked 116 Times in 95 Posts
Originally Posted by datlas
Define “need new chain.”

I get 3000 miles/chain with not much maintenance, replace when elongated by 0.75% or so. Cassettes last longer, around 10K miles.
Me too. I don't get it!

I put on 8,000 miles between 2 cheap derailleur type drivetrains and never changed a chain or sprockets with minimal maintenance. Both worked fine when I gave them away. I didn't even know they wore out until I joined BF's. Ignorance is bliss!

That said, on my recent 2018 bike I brought in for service, they told me my chain was stretched or worn. I didn't measure it so I had them change it since it didn't cost much. I've been checking the new chain and at 1,400 km there is 0 stretching.

I'm sure drivetrain wear is highly dependent on total weight, conditions (hills, tough trails, etc.), rider power applied and proper operation of the drivetrain. Considering my 150 - 160 lbs, mostly flat roads and perhaps average power I suppose my results aren't too surprising.

I worked with a 280 lb man that rode one of those skinny tire road bikes about 15 km to work 5 or 6 days per week. He wore everything out on those bikes every year even on flat roads.

Last edited by xroadcharlie; 06-25-20 at 08:13 AM.
xroadcharlie is offline  
Likes For xroadcharlie:
Old 06-25-20, 09:30 AM
  #10  
Drew Eckhardt 
Senior Member
 
Drew Eckhardt's Avatar
 
Join Date: Apr 2010
Location: Mountain View, CA USA and Golden, CO USA
Posts: 6,341

Bikes: 97 Litespeed, 50-39-30x13-26 10 cogs, Campagnolo Ultrashift, retroreflective rims on SON28/PowerTap hubs

Mentioned: 9 Post(s)
Tagged: 0 Thread(s)
Quoted: 550 Post(s)
Liked 325 Times in 226 Posts
Originally Posted by alloo
How long do your chains and casettes last on your bicycle? With regular maintenance vs w/o maintainance? Miles? Time? I've had two bikes that have needed new chains after about 800 miles is this normal?
I get 4,500 miles out of Campagnolo 10 speed chains which I replace due to degraded front shifting from increased side plate wear causing flexibility. At that point they've only elongated 1/32" over 11" (you won't notice the extra 0.006" of wear over 12", especially past the fractional inch marks on a foot long ruler).

I add oil when they no longer run silently (800 miles in dry weather on factory lube, 100 miles in the rainy season, whatever) but never clean them beyond wiping off the excess. That removes lubrication deep within the chain, risks contaminating the new oil, and is counter productive on road bikes.

I have 25,000 miles on my current nickel-chrome plated cassette, although the new chain skipped a few times accelerating until it wore in on the most recent replacement. It'll go when the current chain stops shifting well.

I never noticed a difference in wear between 135 and 180 pounds.

Last edited by Drew Eckhardt; 06-25-20 at 03:59 PM.
Drew Eckhardt is offline  
Likes For Drew Eckhardt:
Old 06-25-20, 09:38 AM
  #11  
pdlamb
Senior Member
 
Join Date: Dec 2010
Location: northern Deep South
Posts: 8,844

Bikes: Fuji Touring, Novara Randonee

Mentioned: 36 Post(s)
Tagged: 0 Thread(s)
Quoted: 2575 Post(s)
Liked 1,900 Times in 1,192 Posts
All you can really do is check the chain periodically with a ruler.

I normally count on wearing a chain out every 2,000 miles or so. I just checked the other day, and my 2,000 mile old chain is still OK. That's a relief, because the time before last I was too busy having fun to check the chain; after 4,000 miles I had to replace all the chainrings, cassette, and the chain. $Ouch.
pdlamb is offline  
Likes For pdlamb:
Old 06-25-20, 11:35 AM
  #12  
John_V 
Senior Member
 
John_V's Avatar
 
Join Date: Jun 2011
Location: Tampa, Florida
Posts: 5,585

Bikes: 2017 Colnago C-RS, 2012 Colnago Ace, 2010 Giant Cypress hybrid

Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 408 Post(s)
Liked 122 Times in 85 Posts
I used to average around 2,000 miles on both my 10 and 11 speed drive trains. I used various brands of high end chains to see which one gave me the best life and they all were about the same. After being nagged by a friend, I broke down and started using Squirt chain lube with SRAM Red 22 chains. The first Red 22 chain has 4,000 miles on it and my chain tool still hasn't fallen in the links. I changed it with the current chain because I was doing a cross state ride and didn't want any chain problems. It's now a backup chain. The current Red 22 chain has over 3,000 miles and my chain tool isn't showing any wear. I replace my cassettes once a year, whether they need it or not. For me, this combination is a keeper.
__________________
HCFR Cycling Team
Ride Safe ... Ride Hard ... Ride Daily

2017 Colnago C-RS
2012 Colnago Ace
2010 Giant Cypress
John_V is offline  
Likes For John_V:
Old 06-25-20, 12:01 PM
  #13  
pullings
Junior Member
 
Join Date: Jun 2020
Posts: 79
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 28 Post(s)
Liked 35 Times in 17 Posts
2K at best for entry-level SRAM chain.....
Front chainring (1X setup)....5K miles? Always in same ring....and has pretty bad crosschaining wear too. I expect a 2X setup will go twice that?
Rear cassette.....never worn one out before. It seems I always upgrade to something else before I wear one out.
pullings is offline  
Likes For pullings:
Old 06-25-20, 12:41 PM
  #14  
Pop N Wood
Senior Member
 
Join Date: Jun 2020
Location: Maryland
Posts: 1,379

Bikes: 1982 Bianchi Sport SX, Rayleigh Tamland 1, Rans V-Rex recumbent, Fuji MTB, 80's Cannondale MTB with BBSHD ebike motor

Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 667 Post(s)
Liked 529 Times in 355 Posts
When I used to keep track 3500 miles was common for a chain. i do reasonably well with chain maintenance.

Cassettes last a lot longer if you don't ride with a worn out chain. I have worn cassettes to the point where a new chain skipped, but only once. Think that was before I owned a chain stretch gauge. I almost certainly own cassettes that are older than many of the members on this site.

For some people chain maintenance is a religion, almost like they lose sleep worrying about a chain not being optimal. The latest obsession seems to be waxing chains. Do yourself a favor and avoid chain lube arguments.
Pop N Wood is offline  
Likes For Pop N Wood:
Old 06-25-20, 01:49 PM
  #15  
GlennR
On Your Left
 
GlennR's Avatar
 
Join Date: Nov 2011
Location: Long Island, New York, USA
Posts: 8,373

Bikes: Trek Emonda SLR, Sram eTap, Zipp 303

Mentioned: 34 Post(s)
Tagged: 0 Thread(s)
Quoted: 3004 Post(s)
Liked 2,433 Times in 1,187 Posts
I change the Sram Red chain every 3000 miles. I still have my original chainrings and cassette with 24,000, Chains are cheap enough.
GlennR is offline  
Likes For GlennR:
Old 06-25-20, 02:05 PM
  #16  
fietsbob
Banned
 
Join Date: Jun 2010
Location: NW,Oregon Coast
Posts: 43,598

Bikes: 8

Mentioned: 197 Post(s)
Tagged: 0 Thread(s)
Quoted: 7607 Post(s)
Liked 1,354 Times in 861 Posts
I can use the chain checker to measure..

or measure a foot of length.

every link pin was at 1/2" centers when new,

so combined wear is how much longer 12" of chain is than 12" ...
fietsbob is offline  
Old 06-25-20, 04:07 PM
  #17  
datlas 
Should Be More Popular
 
datlas's Avatar
 
Join Date: Dec 2007
Location: Malvern, PA (20 miles West of Philly)
Posts: 42,956

Bikes: 1986 Alpine (steel road bike), 2009 Ti Habenero, 2013 Specialized Roubaix

Mentioned: 560 Post(s)
Tagged: 2 Thread(s)
Quoted: 22512 Post(s)
Liked 8,840 Times in 4,113 Posts
Originally Posted by fietsbob
I can use the chain checker to measure..

or measure a foot of length.

every link pin was at 1/2" centers when new,

so combined wear is how much longer 12" of chain is than 12" ...
1% is definitely worn, so 0.125 inch = 1/8 inch.

Some like to replace at 0.5% which is 1/16 inch.

I split the difference and change at around 0.75%.
__________________
Originally Posted by rjones28
Addiction is all about class.
datlas is offline  
Likes For datlas:
Old 06-25-20, 04:08 PM
  #18  
datlas 
Should Be More Popular
 
datlas's Avatar
 
Join Date: Dec 2007
Location: Malvern, PA (20 miles West of Philly)
Posts: 42,956

Bikes: 1986 Alpine (steel road bike), 2009 Ti Habenero, 2013 Specialized Roubaix

Mentioned: 560 Post(s)
Tagged: 2 Thread(s)
Quoted: 22512 Post(s)
Liked 8,840 Times in 4,113 Posts
The OP has not answered my question about how he/she defines worn chain.

I wonder if the LBS said it was worn.

Bueller??
__________________
Originally Posted by rjones28
Addiction is all about class.
datlas is offline  
Likes For datlas:
Old 06-25-20, 04:39 PM
  #19  
Witterings
Senior Member
 
Join Date: Jul 2010
Location: The Witterings, West Sussex
Posts: 1,066
Mentioned: 8 Post(s)
Tagged: 0 Thread(s)
Quoted: 569 Post(s)
Liked 37 Times in 29 Posts
Originally Posted by datlas

I wonder if the LBS said it was worn.

Bueller??
Must admit I wondered if that was the case as well.
Witterings is offline  
Likes For Witterings:
Old 06-25-20, 05:02 PM
  #20  
alloo
Full Member
Thread Starter
 
alloo's Avatar
 
Join Date: Apr 2019
Location: Albuquerque, NM
Posts: 490

Bikes: 2022 Priority Coast, 2022 Priority Current

Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 175 Post(s)
Liked 137 Times in 99 Posts
Originally Posted by Koyote
OP needs to provide more info:
-What sort of drivetrain? 11sp doesn't last as long as 7sp.
-Ridden in which sort of conditions? Riding in mud and dirt may shorten life of chains and cassettes by more than half.
-What sort of maintenance is being done?
-etc.
I ride a 7 speed bike. 1st bike Shimano Altus 12-32 T Casette 2017 Raleigh Retroglide IE. On my Second Bike Blix Aveny 48T Chainring, and Shimano Acera 14-28 T Casette. The mechanic at a LBS stated that my chain was .75 worn. What drive train changes would you recommend? Chain and Casette for the second bike? My rides are on the street and MUS Trails. Cherry Creek Trail in Denver. Any recommendations are appreciated. Thank You. I do ride in the drizzle, no mud. I've included my commute video.



Last edited by alloo; 06-25-20 at 05:12 PM.
alloo is offline  
Old 06-25-20, 05:52 PM
  #21  
Pop N Wood
Senior Member
 
Join Date: Jun 2020
Location: Maryland
Posts: 1,379

Bikes: 1982 Bianchi Sport SX, Rayleigh Tamland 1, Rans V-Rex recumbent, Fuji MTB, 80's Cannondale MTB with BBSHD ebike motor

Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 667 Post(s)
Liked 529 Times in 355 Posts
I like KMC Z51 chains for my 5-8 speed bikes. Now that I think about it I have a 5, 6, 7 and 8 speed bike.

You won't know if you need a new cassette until you put the new chain on it.
Pop N Wood is offline  
Old 06-25-20, 06:53 PM
  #22  
Koyote
Senior Member
 
Join Date: Sep 2017
Posts: 7,764
Mentioned: 37 Post(s)
Tagged: 0 Thread(s)
Quoted: 6882 Post(s)
Liked 10,871 Times in 4,636 Posts
Originally Posted by alloo
I ride a 7 speed bike. 1st bike Shimano Altus 12-32 T Casette 2017 Raleigh Retroglide IE. On my Second Bike Blix Aveny 48T Chainring, and Shimano Acera 14-28 T Casette. The mechanic at a LBS stated that my chain was .75 worn. What drive train changes would you recommend? Chain and Casette for the second bike? My rides are on the street and MUS Trails. Cherry Creek Trail in Denver. Any recommendations are appreciated. Thank You. I do ride in the drizzle, no mud. I've included my commute video.

https://youtu.be/A3kKvYKYlZQ

https://youtu.be/POB_EmzNc80
7 speed chains last longer than 11 speed, and your conditions don’t seem very harsh. I’m wondering how are you know that they need to be replaced? It just seems too soon.
Koyote is online now  
Old 06-25-20, 08:12 PM
  #23  
u235
Senior Member
 
u235's Avatar
 
Join Date: Mar 2017
Posts: 1,185
Mentioned: 12 Post(s)
Tagged: 0 Thread(s)
Quoted: 437 Post(s)
Liked 133 Times in 86 Posts
I've had some chains last 600 miles. I average about 2000 give or take with a KMC X10SL silver or titanium coated. I swap between 3 cassettes and do not bother to keep track of each run time. I am riding in dirt, gravel, and wet and I cross chain at times. I do at least wipe and relube just about every ride but I am right back in the dust and dirt soon after. It is what it is and I'm not going through great lengths to squeeze some potential life out of of something easily replaceable and only about $35-40.

The KMC X8.93 is a nice low cost chain for a 6/8 speed. Only 7 speed freewheel I a have used recently is a Shimano "megarange" but I doubt that is what you want.

Last edited by u235; 06-25-20 at 08:29 PM.
u235 is offline  
Old 06-27-20, 03:54 AM
  #24  
jpescatore
Senior Member
 
Join Date: Oct 2017
Location: Ashton, MD USA
Posts: 1,296

Bikes: Trek Domane SL6 Disc, Jamis Renegade

Mentioned: 6 Post(s)
Tagged: 0 Thread(s)
Quoted: 363 Post(s)
Liked 304 Times in 217 Posts
If you LBS said it is at .75, they should be able to show you with the chain checker tool they use that it is at .75, which is the recommended replacement indication (for modern chains 9 speed and above. Older 7 speed chains can go down to .5. Nothing immediately dangerous but at the point the chain is worn enough that if it gets more worn it will start to damage the teeth on your cassette. But, ask them to show you, if possible.

If it is really at .75, and you only got 800 miles, take the advice in earlier posts to change some things about the way you ride or take of your chain, or replace the chain more frequently than you would have to.
jpescatore is offline  
Old 06-28-20, 06:01 PM
  #25  
Ross520
Senior Member
 
Join Date: Aug 2019
Posts: 316
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 174 Post(s)
Liked 177 Times in 99 Posts
A drive train in a bike works, and wears very similarly to a manual transmission in a motor vehicle.

If you change your gear oil at religiously, install a magnetic drain plug, double-clutch all of your heel/toe downshifts, gently engage the gears and clutch, avoid launches and clutch kicks, you can go past 200k without even replacing said clutch or having to perform any other repairs for that matter.
​​​​​
On the flip-side, you can blow a gear/clutch/etc., out of a brand-new transmission if you're inexperienced, or are running higher power levels, especially when you add aggressive shifting and clutch modulation to the mix.

Bicycles work the same way, very user-dependent...

Personal, I'm around 1000 miles on chains (DA), and double on my cassettes (Ultegra). I shift and put power through my bicycle transmission similarly to how I do so in my sports cars, aggressively, and my component life reflects that.

As others have mentioned, rider weight, rider power, shift habits, riding conditions, and maintenance level will determine how long your components last.
​​​​​

​​​​
Ross520 is offline  

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.