Quick release skewers not enough threads to tighten rear wheel
#1
Member
Thread Starter
Quick release skewer not enough threads to tighten rear wheel
Hello,
I converted the front wheel on my bike with quick release and I'm having problems with the rear wheel. I installed the quick release axle to the rear wheel and the axle is too long so I cut it with a saw and it solved that but, I'm having another problem. The quick release skewer thread is not enough for the rear wheel so the rear wheel is not secure. Is threre a longer threaded rear wheel skewer that I can buy?
I converted the front wheel on my bike with quick release and I'm having problems with the rear wheel. I installed the quick release axle to the rear wheel and the axle is too long so I cut it with a saw and it solved that but, I'm having another problem. The quick release skewer thread is not enough for the rear wheel so the rear wheel is not secure. Is threre a longer threaded rear wheel skewer that I can buy?
Last edited by Adis; 09-08-20 at 07:22 AM.
#3
Member
Thread Starter
#4
Senior Member
Join Date: Sep 2010
Location: Roswell, GA
Posts: 8,319
Bikes: '93 Trek 750, '92 Schwinn Crisscross, '93 Mongoose Alta
Mentioned: 30 Post(s)
Tagged: 0 Thread(s)
Quoted: 1438 Post(s)
Liked 1,092 Times
in
723 Posts
Is the rear skewer not long enough, or do the threads not go far enough from the end? It sounds like you shortened the axle and now need a shorter skewer because you are running out of threads, is this the situation?
#5
SE Wis
Join Date: Apr 2005
Location: Milwaukee, WI
Posts: 10,499
Bikes: '68 Raleigh Sprite, '02 Raleigh C500, '84 Raleigh Gran Prix, '91 Trek 400, 2013 Novara Randonee, 1990 Trek 970
Mentioned: 40 Post(s)
Tagged: 0 Thread(s)
Quoted: 2740 Post(s)
Liked 3,388 Times
in
2,051 Posts
Does the axle sit within the drop outs and not extend beyond them?
https://www.bikeforums.net/bicycle-m...se-skewer.html
https://www.bikeforums.net/bicycle-m...se-skewer.html
#6
Member
Thread Starter
#7
Senior Member
Join Date: Aug 2005
Location: Pittsburgh, PA
Posts: 33,656
Bikes: '96 Litespeed Catalyst, '05 Litespeed Firenze, '06 Litespeed Tuscany, '20 Surly Midnight Special, All are 3x10. It is hilly around here!
Mentioned: 39 Post(s)
Tagged: 0 Thread(s)
Quoted: 2026 Post(s)
Likes: 0
Liked 1,095 Times
in
741 Posts
What is your rear dropout spacing? If you have a 126 mm OLD frame and hub but have a 135 mm OLD skewer, it would not be threaded far enough to tighten.
Likes For HillRider:
#8
Member
Thread Starter
Likes For dsbrantjr:
#11
Senior Member
Join Date: Sep 2010
Location: Roswell, GA
Posts: 8,319
Bikes: '93 Trek 750, '92 Schwinn Crisscross, '93 Mongoose Alta
Mentioned: 30 Post(s)
Tagged: 0 Thread(s)
Quoted: 1438 Post(s)
Liked 1,092 Times
in
723 Posts
The threads on the current skewer are rolled, not cut, so there will not be sufficient material to cut more threads and still have adequate thread depth, so a shorter skewer is your only choice.
#12
Senior Member
Join Date: Jan 2013
Location: South Jersey
Posts: 2,262
Mentioned: 18 Post(s)
Tagged: 0 Thread(s)
Quoted: 713 Post(s)
Liked 796 Times
in
473 Posts
I would think a skewer for a 130mm wheel would still have enough thread, but here is a skewer for 126mm wheels https://www.loosescrews.com/product/...or-137mm-axle/
#13
Banned
Dropout width kept getting wider as "Speeds" were added _ 120-5, 126-6~7, 130-8 & 135 MTB. & now disc rear wheel ..
(Through axle, went even wider)
you need a QR Skewer from the past era when bikes had 126 mm wide dropouts
(or *hack* add spacers outside of the drop out , not a safe thing unless vertical dropouts.. sketchy even then..)
...
(Through axle, went even wider)
you need a QR Skewer from the past era when bikes had 126 mm wide dropouts
(or *hack* add spacers outside of the drop out , not a safe thing unless vertical dropouts.. sketchy even then..)
...
Last edited by fietsbob; 09-08-20 at 10:12 AM.
#14
Old fart
Join Date: Nov 2004
Location: Appleton WI
Posts: 24,777
Bikes: Several, mostly not name brands.
Mentioned: 153 Post(s)
Tagged: 0 Thread(s)
Quoted: 3582 Post(s)
Liked 3,395 Times
in
1,929 Posts
#15
Newbie
Since you mentioned cutting the axle to size, make sure it does not extend beyond the dropouts. If the axle is slightly too long the QR will clamp against the axle instead of the dropouts and the wheel will not be secure.
#16
Senior Member
Join Date: Jun 2002
Location: Montreal, Quebec
Posts: 5,921
Mentioned: 16 Post(s)
Tagged: 0 Thread(s)
Quoted: 1815 Post(s)
Liked 1,693 Times
in
974 Posts
It appears that you bought an axle that was too long for your application and that the skewer was sized for that axle. It is possible but not ideal to cut the axle to a shorter length but not the quick release. All this could have been avoided by buying the correct length parts in the first place.