Spoke tensioning
#1
Senior Member
Thread Starter
Join Date: Feb 2014
Posts: 71
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 20 Post(s)
Likes: 0
Liked 2 Times
in
2 Posts
Spoke tensioning
I have a question about ideal spoke tensioning.
I recently rebuilt my Wabi Cycles front wheel at a local volunteer shop. It's a 32H wheel with 14/15 double butted stainless spokes and a 100mm low flange hub. The mechanic said that the true of the wheel was more important than the tension reading, and he suggested that I get the wheel in true with the individual spoke tensions between 15 and 20 (using a Park Tool Tensiometer). I got the spokes all somewhere between 16 and 18 with the wheel as true as I could reasonably get it.
Later, I compared the spoke tension of the rebuilt front wheel to my rear wheel by squeezing them. It seems as if my rear wheel is noticeably tighter, but I would have to use a tensiometer to be sure. Using Park Tool's conversion table it looks like the tension in the front wheel spokes is something between 70 and 90 kgf for my 1.8mm spokes. How does this sound? Could my rear wheel be too tight?
I recently rebuilt my Wabi Cycles front wheel at a local volunteer shop. It's a 32H wheel with 14/15 double butted stainless spokes and a 100mm low flange hub. The mechanic said that the true of the wheel was more important than the tension reading, and he suggested that I get the wheel in true with the individual spoke tensions between 15 and 20 (using a Park Tool Tensiometer). I got the spokes all somewhere between 16 and 18 with the wheel as true as I could reasonably get it.
Later, I compared the spoke tension of the rebuilt front wheel to my rear wheel by squeezing them. It seems as if my rear wheel is noticeably tighter, but I would have to use a tensiometer to be sure. Using Park Tool's conversion table it looks like the tension in the front wheel spokes is something between 70 and 90 kgf for my 1.8mm spokes. How does this sound? Could my rear wheel be too tight?
#3
Senior Member
Join Date: Feb 2019
Posts: 198
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 92 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
I have a question about ideal spoke tensioning.
I recently rebuilt my Wabi Cycles front wheel at a local volunteer shop. It's a 32H wheel with 14/15 double butted stainless spokes and a 100mm low flange hub. The mechanic said that the true of the wheel was more important than the tension reading, and he suggested that I get the wheel in true with the individual spoke tensions between 15 and 20 (using a Park Tool Tensiometer). I got the spokes all somewhere between 16 and 18 with the wheel as true as I could reasonably get it.
Later, I compared the spoke tension of the rebuilt front wheel to my rear wheel by squeezing them. It seems as if my rear wheel is noticeably tighter, but I would have to use a tensiometer to be sure. Using Park Tool's conversion table it looks like the tension in the front wheel spokes is something between 70 and 90 kgf for my 1.8mm spokes. How does this sound? Could my rear wheel be too tight?
I recently rebuilt my Wabi Cycles front wheel at a local volunteer shop. It's a 32H wheel with 14/15 double butted stainless spokes and a 100mm low flange hub. The mechanic said that the true of the wheel was more important than the tension reading, and he suggested that I get the wheel in true with the individual spoke tensions between 15 and 20 (using a Park Tool Tensiometer). I got the spokes all somewhere between 16 and 18 with the wheel as true as I could reasonably get it.
Later, I compared the spoke tension of the rebuilt front wheel to my rear wheel by squeezing them. It seems as if my rear wheel is noticeably tighter, but I would have to use a tensiometer to be sure. Using Park Tool's conversion table it looks like the tension in the front wheel spokes is something between 70 and 90 kgf for my 1.8mm spokes. How does this sound? Could my rear wheel be too tight?
#4
Senior Member
Join Date: Feb 2019
Posts: 198
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 92 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
I have a question about ideal spoke tensioning.
I recently rebuilt my Wabi Cycles front wheel at a local volunteer shop. It's a 32H wheel with 14/15 double butted stainless spokes and a 100mm low flange hub. The mechanic said that the true of the wheel was more important than the tension reading, and he suggested that I get the wheel in true with the individual spoke tensions between 15 and 20 (using a Park Tool Tensiometer). I got the spokes all somewhere between 16 and 18 with the wheel as true as I could reasonably get it.
Later, I compared the spoke tension of the rebuilt front wheel to my rear wheel by squeezing them. It seems as if my rear wheel is noticeably tighter, but I would have to use a tensiometer to be sure. Using Park Tool's conversion table it looks like the tension in the front wheel spokes is something between 70 and 90 kgf for my 1.8mm spokes. How does this sound? Could my rear wheel be too tight?
I recently rebuilt my Wabi Cycles front wheel at a local volunteer shop. It's a 32H wheel with 14/15 double butted stainless spokes and a 100mm low flange hub. The mechanic said that the true of the wheel was more important than the tension reading, and he suggested that I get the wheel in true with the individual spoke tensions between 15 and 20 (using a Park Tool Tensiometer). I got the spokes all somewhere between 16 and 18 with the wheel as true as I could reasonably get it.
Later, I compared the spoke tension of the rebuilt front wheel to my rear wheel by squeezing them. It seems as if my rear wheel is noticeably tighter, but I would have to use a tensiometer to be sure. Using Park Tool's conversion table it looks like the tension in the front wheel spokes is something between 70 and 90 kgf for my 1.8mm spokes. How does this sound? Could my rear wheel be too tight?
#5
Senior Member
Thread Starter
Join Date: Feb 2014
Posts: 71
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 20 Post(s)
Likes: 0
Liked 2 Times
in
2 Posts
Originally Posted by Bikesplendor
Why not get some tensiometer readings on the rear wheel as well, on both sides?
#6
Senior Member
Join Date: May 2008
Location: Zang's Spur, CO
Posts: 9,083
Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 3375 Post(s)
Liked 5,512 Times
in
2,855 Posts
#7
Senior Member
Join Date: Feb 2012
Location: Rochester, NY
Posts: 18,071
Bikes: Stewart S&S coupled sport tourer, Stewart Sunday light, Stewart Commuting, Stewart Touring, Co Motion Tandem, Stewart 3-Spd, Stewart Track, Fuji Finest, Mongoose Tomac ATB, GT Bravado ATB, JCP Folder, Stewart 650B ATB
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4199 Post(s)
Liked 3,851 Times
in
2,301 Posts
I usually aim for ft spoke tension somewhat between the two sides of a typical rear wheel (that has rather off set flange to center of axle ends due to the many cogs on one side. A flip flop will have much less offset and thus less tension difference).
I will take some issue with the mechanic who placed trueness over tension. Both are nice to have proper but I would place a higher value of evenness of tension then absolute trueness. A consistently tensioned wheel will tend to be more stable and reliable over the miles then one that initially looks straighter but has some spokes fatiguing faster then others. Andy
I will take some issue with the mechanic who placed trueness over tension. Both are nice to have proper but I would place a higher value of evenness of tension then absolute trueness. A consistently tensioned wheel will tend to be more stable and reliable over the miles then one that initially looks straighter but has some spokes fatiguing faster then others. Andy
__________________
AndrewRStewart
AndrewRStewart
#8
Mostly harmless ™
Join Date: Nov 2010
Location: Novi Sad
Posts: 4,430
Bikes: Heavy, with friction shifters
Mentioned: 22 Post(s)
Tagged: 0 Thread(s)
Quoted: 1107 Post(s)
Liked 216 Times
in
130 Posts
I usually aim for ft spoke tension somewhat between the two sides of a typical rear wheel (that has rather off set flange to center of axle ends due to the many cogs on one side. A flip flop will have much less offset and thus less tension difference).
I will take some issue with the mechanic who placed trueness over tension. Both are nice to have proper but I would place a higher value of evenness of tension then absolute trueness. A consistently tensioned wheel will tend to be more stable and reliable over the miles then one that initially looks straighter but has some spokes fatiguing faster then others. Andy
I will take some issue with the mechanic who placed trueness over tension. Both are nice to have proper but I would place a higher value of evenness of tension then absolute trueness. A consistently tensioned wheel will tend to be more stable and reliable over the miles then one that initially looks straighter but has some spokes fatiguing faster then others. Andy
Question1:
In my experience, some wheels (rims) get "too untrue" when spoke tension is withing 1% of each other. In those cases, In those cases, I aim for spoke tension to be within +-7 % (even 10% on some rims that aren't in "nice condition") of a certain medium value - in order to get the wheel straight, without (what I think would be) too much difference in tension. I think of it as a compromise: even spoke tension makes a wheel last longer, but trueness (with at least decent amount of tension) makes it ride nicer.
Do you think that's a good policy, or should I aim for tension eveness, even if a rim is more noticeably out of true?
Question 2:
Could it be that what I said above, the OP's mechanic was also saying, only more awkward with words?
I've seen good mechanics who don't explain stuff all too well - combine that with an average novice (no offence meant to anyone) - you get all sorts of "but the mechanic said..." that you would never think a mechanic with a grain of experience would say.
Hell - I've heard people draw wrong conclusions from Sheldon Brown's and my website - then having asked them: "show me/tell me where that's said, it should be corrected ASAP" - they realize it's just bad reading/understanding on their part.
#9
Senior Member
Join Date: Feb 2004
Location: St Peters, Missouri
Posts: 30,225
Bikes: Catrike 559 I own some others but they don't get ridden very much.
Mentioned: 16 Post(s)
Tagged: 0 Thread(s)
Quoted: 1572 Post(s)
Liked 643 Times
in
364 Posts
The numbers on your tensiometer are just numbers. They really don't mean anything other than 18 is higher, thus tighter, than 16. If your goal is 110 kgf, here's how to be sure:
1. The hard part is finding a standard. You need to find a spoke the same diameter and metallurgy as the ones that you are working with that is also known to have exactly 110 kgf of tension.
2. Measure that spoke with your tensiometer. Notice what the reading is. Match that reading as you are tensioning your wheel and you'll achieve your target tension.
So now you've got your wheel as true as you think reasonable with tension readings as close as you can achieve but the overall wheel tension is less than your proven reliable rear wheel. That's the balance between tension and trueness that you are looking for, but you're still not up to full tension yet.
If it was my wheel I'd tighten every spoke 1/2 turn and compare my spoke tensions with my rear wheel again. If they still seemed loose, I'd tighten every spoke another 1/2 turn until they feel about the same. It doesn't really matter if you compare your wheel with your known reliable wheel by feeling the tension with your fingers, plucking the spokes for tone, or using your tensiometer.
1. The hard part is finding a standard. You need to find a spoke the same diameter and metallurgy as the ones that you are working with that is also known to have exactly 110 kgf of tension.
2. Measure that spoke with your tensiometer. Notice what the reading is. Match that reading as you are tensioning your wheel and you'll achieve your target tension.
So now you've got your wheel as true as you think reasonable with tension readings as close as you can achieve but the overall wheel tension is less than your proven reliable rear wheel. That's the balance between tension and trueness that you are looking for, but you're still not up to full tension yet.
If it was my wheel I'd tighten every spoke 1/2 turn and compare my spoke tensions with my rear wheel again. If they still seemed loose, I'd tighten every spoke another 1/2 turn until they feel about the same. It doesn't really matter if you compare your wheel with your known reliable wheel by feeling the tension with your fingers, plucking the spokes for tone, or using your tensiometer.
__________________
My greatest fear is all of my kids standing around my coffin and talking about "how sensible" dad was.
My greatest fear is all of my kids standing around my coffin and talking about "how sensible" dad was.
#10
Banned.
Join Date: Jun 2004
Location: Torrance, CA
Posts: 3,061
Bikes: Homebuilt steel
Mentioned: 18 Post(s)
Tagged: 0 Thread(s)
Quoted: 2193 Post(s)
Liked 425 Times
in
337 Posts
Tension meters like the Park has an app which allows you to translate the gauges tension numbers into actual spoke tension values in kgf. Targeting 110 for DS rear is about right. For the front you generally don't need to go quite that high.
#11
working on my sandal tan
Join Date: Aug 2011
Location: CID
Posts: 22,629
Bikes: 1991 Bianchi Eros, 1964 Armstrong, 1988 Diamondback Ascent, 1988 Bianchi Premio, 1987 Bianchi Sport SX, 1980s Raleigh mixte (hers), All-City Space Horse (hers)
Mentioned: 98 Post(s)
Tagged: 0 Thread(s)
Quoted: 3871 Post(s)
Liked 2,568 Times
in
1,579 Posts
https://www.parktool.com/assets/doc/...conv-table.pdf
I like to use strips of painter's tape to cover up the neighboring spoke gauges of the wheel I'm working on. That helps avoid mistakes when going back and forth between the wheel and the chart.
#12
Senior Member
Thread Starter
Join Date: Feb 2014
Posts: 71
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 20 Post(s)
Likes: 0
Liked 2 Times
in
2 Posts
I took my old rear wheel back to the shop and checked the spoke tension with the TM-1. All the spokes read something around 25. This wheel is 5-6 years old and I've never lost a spoke on it despite me riding it basically everyday, so I assume it's tension serves as a pretty good ideal tension (at least for durabilities sake).
As mentioned by a few people here, the mechanic at the shop (a different mechanic because its a volunteer shop) suggested that I tension the front wheel to be less than the rear, but close to being the same. He also agreed with the previous mechanic that having all the spoke tensions within 2-3 on the TM-1 scale was perfectly fine provided the wheel was in true. Perhaps if one had a truly accurate tensiometer and was skilled at getting accurate tension readings it would be worth getting the tensions of the spokes all very similar. However, given the roughness of the tool being used and my novice ability to use it, I reckon I'm can't get a very accurate spoke tension reading anyway.
Given this, I took the front wheel's tension up to 20-22 while maintaining good true.
As mentioned by a few people here, the mechanic at the shop (a different mechanic because its a volunteer shop) suggested that I tension the front wheel to be less than the rear, but close to being the same. He also agreed with the previous mechanic that having all the spoke tensions within 2-3 on the TM-1 scale was perfectly fine provided the wheel was in true. Perhaps if one had a truly accurate tensiometer and was skilled at getting accurate tension readings it would be worth getting the tensions of the spokes all very similar. However, given the roughness of the tool being used and my novice ability to use it, I reckon I'm can't get a very accurate spoke tension reading anyway.
Given this, I took the front wheel's tension up to 20-22 while maintaining good true.
#13
Senior Member
Join Date: Feb 2004
Location: St Peters, Missouri
Posts: 30,225
Bikes: Catrike 559 I own some others but they don't get ridden very much.
Mentioned: 16 Post(s)
Tagged: 0 Thread(s)
Quoted: 1572 Post(s)
Liked 643 Times
in
364 Posts
Another digital vs. analogue discussion. The wisdom comes in understanding when it's better to use which.
__________________
My greatest fear is all of my kids standing around my coffin and talking about "how sensible" dad was.
My greatest fear is all of my kids standing around my coffin and talking about "how sensible" dad was.