Good short vid on silver brazing
#1
Senior Member
Thread Starter
Join Date: Mar 2012
Location: santa barbara CA
Posts: 1,087
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 96 Post(s)
Liked 30 Times
in
21 Posts
Good short vid on silver brazing
Overall good short footage and info on the basics of silver brazing. Jody(welding tips and tricks) is not a frame builder but visits Mike at his shop.
regards, Brian
regards, Brian
__________________
Brian
Brian
Last edited by calstar; 02-16-19 at 12:27 PM.
#2
Senior Member
Join Date: Aug 2014
Location: Capestang, France
Posts: 1,341
Bikes: Lots of French, some British and a couple of Italian
Mentioned: 35 Post(s)
Tagged: 0 Thread(s)
Quoted: 247 Post(s)
Liked 130 Times
in
65 Posts
I read an article by an 'old' framebuilder saying silver braze gives better performance than bronze. If there's any truth to that, maybe it's that the initial clearance in the joint needs to be much tighter? Nice vid, thanks.
#3
Banned.
Join Date: Jun 2004
Location: Torrance, CA
Posts: 3,061
Bikes: Homebuilt steel
Mentioned: 18 Post(s)
Tagged: 0 Thread(s)
Quoted: 2193 Post(s)
Liked 425 Times
in
337 Posts
I like silver because it's lower temperature (than brass) and flows really well (56% or ezflow 45% w/cad). Brass is fine but more heat is needed and thus greater skill is required to make sure you don't overheat the metal. Also, silver is easier to remove from the shore line than brass (for those instances where you get caught trying to over fill the joint.)
#4
Senior Member
Join Date: Feb 2012
Location: Rochester, NY
Posts: 18,053
Bikes: Stewart S&S coupled sport tourer, Stewart Sunday light, Stewart Commuting, Stewart Touring, Co Motion Tandem, Stewart 3-Spd, Stewart Track, Fuji Finest, Mongoose Tomac ATB, GT Bravado ATB, JCP Folder, Stewart 650B ATB
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4194 Post(s)
Liked 3,837 Times
in
2,295 Posts
To play the devil's advocate- Brass is far more tolerant of poor prep. Both in gap as well as clean surfaces. It's much less expensive and offers far more joint geometry and styles. It has a greater temp range WRT it's viscosity, meaning it can flow quickly or glob up (lugs or fillet). That the temp is greater and thus the control of temp is more critical is only practice, just like flowing silver is practice and maintaining the temp for that takes a skill. Andy
__________________
AndrewRStewart
AndrewRStewart
#5
Old fart
Join Date: Nov 2004
Location: Appleton WI
Posts: 24,776
Bikes: Several, mostly not name brands.
Mentioned: 153 Post(s)
Tagged: 0 Thread(s)
Quoted: 3582 Post(s)
Liked 3,394 Times
in
1,928 Posts
Brass is more tolerant of poor prep and looser clearances, but silver's lower temperature can mean a smaller heat-affected zone on the tubing. Silver also flows easier than brass, and done well requires less clean-up.
#6
Randomhead
Join Date: Aug 2008
Location: Happy Valley, Pennsylvania
Posts: 24,385
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4 Post(s)
Liked 3,686 Times
in
2,509 Posts
I hate to file, so I'm sticking with silver for the time being
#7
Senior Member
Join Date: Feb 2012
Location: Rochester, NY
Posts: 18,053
Bikes: Stewart S&S coupled sport tourer, Stewart Sunday light, Stewart Commuting, Stewart Touring, Co Motion Tandem, Stewart 3-Spd, Stewart Track, Fuji Finest, Mongoose Tomac ATB, GT Bravado ATB, JCP Folder, Stewart 650B ATB
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4194 Post(s)
Liked 3,837 Times
in
2,295 Posts
And I'm sure you're a faster builder then I am too Andy
__________________
AndrewRStewart
AndrewRStewart
#8
Senior Member
Great video and a as traditional silversmith I'd say he hit all the bases.
his web site is also a great for most welding tec.
his web site is also a great for most welding tec.
#9
Senior Member
Thread Starter
Join Date: Mar 2012
Location: santa barbara CA
Posts: 1,087
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 96 Post(s)
Liked 30 Times
in
21 Posts
Looks like a small piece of crud in the orifice at 3:10 in (and seen throughout the brazing) causing slight separation of cone and feather. Doesn't effect the procedure but would you clean the tip before next use?
thanks, Brian
thanks, Brian
__________________
Brian
Brian
Last edited by calstar; 02-24-19 at 12:05 PM.
#10
Senior Member
Join Date: Feb 2012
Location: Rochester, NY
Posts: 18,053
Bikes: Stewart S&S coupled sport tourer, Stewart Sunday light, Stewart Commuting, Stewart Touring, Co Motion Tandem, Stewart 3-Spd, Stewart Track, Fuji Finest, Mongoose Tomac ATB, GT Bravado ATB, JCP Folder, Stewart 650B ATB
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4194 Post(s)
Liked 3,837 Times
in
2,295 Posts
Brian- yes, I would clean the tip. Both ID and face. But In try to go easy when using tip cleaning "reamers" as to not open up the orifice too much too. Andy
__________________
AndrewRStewart
AndrewRStewart
#11
Randomhead
Join Date: Aug 2008
Location: Happy Valley, Pennsylvania
Posts: 24,385
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4 Post(s)
Liked 3,686 Times
in
2,509 Posts
I would clean it if I remember. Then I would get flux on it and it would happen all over again. It's mostly just an annoyance.