Alternative to rags for cleaning, lubing chain
#1
Junior Member
Thread Starter
Join Date: Mar 2019
Posts: 15
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 7 Post(s)
Likes: 0
Liked 2 Times
in
2 Posts
Alternative to rags for cleaning, lubing chain
I like to pull the Townie and my Giant Cypress out once in a while and wipe the chains and apply a chain lubricant. I usually use household rags for this job, and then I throw them away because they're so dirty. Is there an alternative to rags for this job? Paper towels or baby wipes or something.
Any input is appreciated. Thank you.
Any input is appreciated. Thank you.
#3
Really Old Senior Member
Cats. They clean themselves.
#4
Senior Member
Join Date: Feb 2012
Location: Golden, CO and Tucson, AZ
Posts: 2,836
Bikes: 2016 Fuji Tread, 1983 Trek 520
Mentioned: 13 Post(s)
Tagged: 0 Thread(s)
Quoted: 675 Post(s)
Liked 741 Times
in
430 Posts
If the chain is off the bike I'll hit it with a wire brush. Otherwise I throw away the rags (with all due care to oily rags--avoid spontaneous combustion).
I get many of my rags on the roadside, especially in boating areas on summer weekends. So I don't feel so bad about eventually throwing them away, since they were once litter I picked up.
Since I share a washing machine with people I love, I don't put greasy rags in the laundry (any more).
I get many of my rags on the roadside, especially in boating areas on summer weekends. So I don't feel so bad about eventually throwing them away, since they were once litter I picked up.
Since I share a washing machine with people I love, I don't put greasy rags in the laundry (any more).
#5
Very Senior Member
Join Date: Mar 2018
Location: Always on the Run
Posts: 1,211
Bikes: Giant Quasar & Fuji Roubaix
Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 413 Post(s)
Liked 343 Times
in
244 Posts
I have a Rubbermaid just for worn out fabrix that I keep handy for dirty jobs. It might contain old bed sheets, towels, cotton shirts and Tees, anything that will absorb goes into it instead of the garbage. But yeah, I like to wash it first and then just use the rag for drying before waxing. Hey Bill, do cats really make a good chain? Do you use the whole cat or just the catgut? A self cleaning chain would be really cool.
#6
Mother Nature's Son
Join Date: Mar 2016
Location: Sussex County, Delaware
Posts: 3,113
Bikes: 2014 Orbea Avant MD30, 2004 Airborne Zeppelin TI, 2003 Lemond Poprad, 2001 Lemond Tourmalet, 2014? Soma Smoothie
Mentioned: 15 Post(s)
Tagged: 0 Thread(s)
Quoted: 852 Post(s)
Liked 1,433 Times
in
815 Posts
I cannot remember where I saw it, but there is a sponge that is made and shaped just for cleaning chains. It has a ridge running down the center of the sponge that is supposed to assist in cleaning the inside of the links. It is also supposed to be easy to clean and last for a number of cleanings. I was kind of skeptical but there were a couple of good reviews. Anybody out there that knows of and where to get it?
#7
The dropped
Join Date: Oct 2018
Location: Columbus, OH
Posts: 2,144
Bikes: Pake C'Mute Touring/Commuter Build, 1989 Kona Cinder Cone, 1995 Trek 5200, 1973 Raleigh Super Course FG, 1960/61 Montgomery Ward Hawthorne "thrift" 3 speed, by Hercules (sold) : 1966 Schwinn Deluxe Racer (sold)
Mentioned: 10 Post(s)
Tagged: 0 Thread(s)
Quoted: 1739 Post(s)
Liked 1,014 Times
in
696 Posts
#8
The dropped
Join Date: Oct 2018
Location: Columbus, OH
Posts: 2,144
Bikes: Pake C'Mute Touring/Commuter Build, 1989 Kona Cinder Cone, 1995 Trek 5200, 1973 Raleigh Super Course FG, 1960/61 Montgomery Ward Hawthorne "thrift" 3 speed, by Hercules (sold) : 1966 Schwinn Deluxe Racer (sold)
Mentioned: 10 Post(s)
Tagged: 0 Thread(s)
Quoted: 1739 Post(s)
Liked 1,014 Times
in
696 Posts
Simple Green is a miracle surfactant
Full strength simple green cleaner will remove roofing sealant. You should be able to dump some on the rag you use and hand wash the worst of off it, then wash with other rags.
Don't put the simple green in your washer in any significant amount though, unless you like bubbles.
Don't put the simple green in your washer in any significant amount though, unless you like bubbles.
#9
Full Member
Join Date: Aug 2014
Location: ETX/ SNH
Posts: 225
Bikes: 2011 Handsome/ Twin Six Speedy Devil, 2006 Soma Groove, 1991 Haro Impulse Comp, 1987 KHS Montana Pro, 1986 Ross Mount Hood, 1986 Mongoose ATB, 1985 Shogun Prairie Breaker I, 1973 World Voyageur, 1941 Schwinn DX "Klunker"
Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 83 Post(s)
Liked 96 Times
in
45 Posts
I have an old plastic popcorn jar with a wide mouth that I keep about 1/2 full of mineral spirits. I drop the chain in and let it soak, give it a few shakes, soak, shake ... over a day or so. Pull the chain out and let it drip dry over paper towels then reinstall and lube.
#10
Senior Member
Join Date: May 2010
Location: Bristol, R. I.
Posts: 4,340
Bikes: Specialized Secteur, old Peugeot
Mentioned: 20 Post(s)
Tagged: 0 Thread(s)
Quoted: 663 Post(s)
Liked 496 Times
in
299 Posts
Here in the US, Ace Hardware stores have rolls of heavy duty paper towel that are perfect for wiping off chains. I suspect Auto Zone or other auto supply stores have them also.
#11
Droid on a mission
Join Date: May 2018
Location: Palm Coast, FL
Posts: 1,005
Bikes: Diamondback Wildwood Classic
Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 317 Post(s)
Liked 280 Times
in
195 Posts
https://www.homedepot.com/p/Scott-Sh...5143/202519693
https://www.harborfreight.com/dispos..._q=shop+towels
https://www.pepboys.com/sellars-tool...510?quantity=1
__________________
JoeTBM (The Bike Man) - I'm a black & white type of guy, the only gray in my life is the hair on my head
www.TheBikeMenOfFlaglerCounty.com
JoeTBM (The Bike Man) - I'm a black & white type of guy, the only gray in my life is the hair on my head
www.TheBikeMenOfFlaglerCounty.com
Likes For JoeTBM:
#12
Senior Member
Join Date: Mar 2010
Location: new berlin wi
Posts: 232
Bikes: trek 720 multitrack hybred, 92 trek 2300, 2010 specialized roubaix, 2014 specialized roubaix
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 14 Post(s)
Likes: 0
Liked 17 Times
in
14 Posts
maybe try some mechanic hand cleaning wipes, they will have something to cut grease and grime in the wipe. after you are done throw away.
possibly something like this....https://www.menards.com/main/health-...2823301788.htm
possibly something like this....https://www.menards.com/main/health-...2823301788.htm
#14
Senior Member
Curious about the Gojo. I may try that next.
Currently I wipe down my chain after every ride using the Scott shop towels and degreaser. I spray the degreaser mix (simple green) lightly directly onto the towel and just wipe the outside of the chain. I make sure I don't put enough degreaser to soak into the chain pivots/rivets so that it doesn't dissolve the chain lube inside the pivots. Just a light enough spray to cut through the grime on the outside of the chain. Then I do a second pass with just the shop towel, to remove any trace of the degreaser from the outside of the chain, and discard the towel.
About every 100 miles or so I reapply the Finish Line wet lube. The chain/transmission noise will tell me when I need to. It's very quiet right after cleaning and application, but then after maybe 5 or so rides of between 10-25 miles, if after doing the quick wipe down it is still markedly noisier, then I'll do a reapplication of the lube.
After maybe 500 miles I'll do a deep clean of the chain using the Park Tool chain cleaner tool and full strength chain degreaser, followed by a pass with soapy water, then multiple passes with regular water and allow to air dry before applying the lube again, one drop on each pivot. Since I ride just about every day, this ends up being maybe once every 4-5 weeks. More frequently if I've done riding in very dusty/sandy areas like trails or beach-side paths.
Currently I wipe down my chain after every ride using the Scott shop towels and degreaser. I spray the degreaser mix (simple green) lightly directly onto the towel and just wipe the outside of the chain. I make sure I don't put enough degreaser to soak into the chain pivots/rivets so that it doesn't dissolve the chain lube inside the pivots. Just a light enough spray to cut through the grime on the outside of the chain. Then I do a second pass with just the shop towel, to remove any trace of the degreaser from the outside of the chain, and discard the towel.
About every 100 miles or so I reapply the Finish Line wet lube. The chain/transmission noise will tell me when I need to. It's very quiet right after cleaning and application, but then after maybe 5 or so rides of between 10-25 miles, if after doing the quick wipe down it is still markedly noisier, then I'll do a reapplication of the lube.
After maybe 500 miles I'll do a deep clean of the chain using the Park Tool chain cleaner tool and full strength chain degreaser, followed by a pass with soapy water, then multiple passes with regular water and allow to air dry before applying the lube again, one drop on each pivot. Since I ride just about every day, this ends up being maybe once every 4-5 weeks. More frequently if I've done riding in very dusty/sandy areas like trails or beach-side paths.
#15
Senior Member
Scott shop towels work great. I buy a bundle of 12 rolls at Sam's club. I use mineral spirits or camp stove fuel for degreaser, never anything water based. Crown brand camp stove fuel at Wal-Mart is a lot cheaper than mineral spirits and evaporates faster.
With my home brew wax based lube, I can easily go 120 miles with no wiping. Then I wipe the chain with a shop towel that has a little camp stove fuel on it and reapply the dry lube. This gives me the cleanest drivetrain I've ever had.
With my home brew wax based lube, I can easily go 120 miles with no wiping. Then I wipe the chain with a shop towel that has a little camp stove fuel on it and reapply the dry lube. This gives me the cleanest drivetrain I've ever had.
#16
Senior Member
Join Date: Jun 2002
Location: Montreal, Quebec
Posts: 5,925
Mentioned: 16 Post(s)
Tagged: 0 Thread(s)
Quoted: 1818 Post(s)
Liked 1,693 Times
in
974 Posts
I don't buy any disposable product for cleaning my bike chain. I have found that old terrycloth towels are the best thing to clean chains. They are absorbent and the nap of the towel gets well in between chain links. One facecloth sized piece of towel can be used many times after having been used many times before for many other things. I used to use old towels to dry my car after having washed it, this after years of use drying me off after a shower. They were also great for washing windows, could be used many times for that. Once they became more frayed, I would cut them up to clean my bike chains, they wore much better than a plain rag. Once they are saturated with dirt and oil from chain cleaning, it is time to dispose of them. I would never buy a one time use product for wiping my bike chain
#17
Full Member
Nobody here uses a chain cleaner? I've been using one for 20 years. I use Simple Green or Citrus based cleaner and then dispose of the waste using household hazardous waste pickup.
Edit: I noticed CarloM uses one.
Edit: I noticed CarloM uses one.
Likes For hhk25:
#18
Senior Member
An on the bike cleaner takes at least two times to really clean a chain. If water based products are used, they leave residue on the chain. They also have to leave cleaning fluid residue on the sprockets, chain rings, and hub . Cleaning the chain is best done with it off the bike.
#20
Senior Member
Major missed opportunity for me. About a month before I got into cycling I discarded a bunch of old white cotton undershirts and socks that had gotten hole-y with age. I would have had chain rags for months if I hadn't discarded those...
#21
Insane Bicycle Mechanic
Join Date: Mar 2008
Location: other Vancouver
Posts: 9,835
Mentioned: 34 Post(s)
Tagged: 0 Thread(s)
Quoted: 802 Post(s)
Liked 703 Times
in
376 Posts
They can be trained to check spoke tension, too:
(From the https://www.bikeforums.net/classic-v...ur-cat-72.html thread.)
(From the https://www.bikeforums.net/classic-v...ur-cat-72.html thread.)
__________________
Jeff Wills
Comcast nuked my web page. It will return soon..
Jeff Wills
Comcast nuked my web page. It will return soon..
Likes For Jeff Wills:
#23
Senior Member
I use the Park cleaner myself, but since I went to a wax lube the chain doesn't get nearly as dirty. You need to apply it more often but it really makes for a quiet and clean ride. You can run your hand over my chain and not have a semi-permanent tattoo on it, just a little smudge. Squirt brand is what I'm using, specially designed to do exactly this. I apply every 100-150 miles on two different bikes.
#24
Señor Member
Join Date: Feb 2013
Posts: 5,066
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 649 Post(s)
Liked 292 Times
in
215 Posts
I keep one very dirty rag just for wiping my dirty chain, when there are no more clean surfaces on it I throw it away. I also have clean rags handy for jobs that require it - cleaning bearing surfaces before relubing, for instance, and most of these will eventually graduate to being chain wiping rags.
#25
Senior Member
Join Date: Apr 2012
Location: Nor Cal
Posts: 6,016
Mentioned: 17 Post(s)
Tagged: 0 Thread(s)
Quoted: 1814 Post(s)
Likes: 0
Liked 923 Times
in
569 Posts
I use plain paper towels for initial chain-wiping, then rags.
One tee shirt cuts up into ~25 rags and since
they are used for progressively greasier tasks, that is a two year supply.
One tee shirt cuts up into ~25 rags and since
they are used for progressively greasier tasks, that is a two year supply.