Identify Bottom Bracket Tool Needed ?
#2
Senior Member
Join Date: Feb 2013
Location: Alta California
Posts: 14,271
Mentioned: 415 Post(s)
Tagged: 1 Thread(s)
Quoted: 3814 Post(s)
Liked 3,345 Times
in
2,182 Posts
-----
posting a spline count might help readers to help you
with all the foreign matter present it is difficult to count
-----
posting a spline count might help readers to help you
with all the foreign matter present it is difficult to count
-----
#3
Insane Bicycle Mechanic
Join Date: Mar 2008
Location: other Vancouver
Posts: 9,843
Mentioned: 34 Post(s)
Tagged: 0 Thread(s)
Quoted: 809 Post(s)
Liked 712 Times
in
380 Posts
I would like to see the rest of the crank but I suspect it’s a Shimano FFS crank and its backwards Octa-joint bottom bracket. In order to remove the cups, you need an early Shimano freewheel tool, TL-FW20. These are rare but can be found. It fits the splines in the cups and they unscrew like other English-threaded cups: right side cup is left-hand threaded.
__________________
Jeff Wills
Comcast nuked my web page. It will return soon..
Jeff Wills
Comcast nuked my web page. It will return soon..
#4
Ride, Wrench, Swap, Race
Join Date: Jan 2010
Location: Northern California
Posts: 9,194
Bikes: Cheltenham-Pedersen racer, Boulder F/S Paris-Roubaix, Varsity racer, '52 Christophe, '62 Continental, '92 Merckx, '75 Limongi, '76 Presto, '72 Gitane SC, '71 Schwinn SS, etc.
Mentioned: 132 Post(s)
Tagged: 0 Thread(s)
Quoted: 1565 Post(s)
Liked 1,296 Times
in
866 Posts
Are you needing to remove the cups in order to replace them with normal parts?
If so, you could use a piece of 1/4" steel flat stock to turn the cups out after cutting or grinding opposing notches adjacent to the splined hole.
A very large adjustable wrench, pipe wrench or bench vise might then be used to apply torque to the flat stock removal tool.
I believe that the needed tool is usually not hollow like common freewheel tools, which makes identifying one a little easier.
If so, you could use a piece of 1/4" steel flat stock to turn the cups out after cutting or grinding opposing notches adjacent to the splined hole.
A very large adjustable wrench, pipe wrench or bench vise might then be used to apply torque to the flat stock removal tool.
I believe that the needed tool is usually not hollow like common freewheel tools, which makes identifying one a little easier.
#5
Bianchi Goddess
Join Date: Apr 2009
Location: Shady Pines Retirement Fort Wayne, In
Posts: 27,866
Bikes: Too many to list here check my signature.
Mentioned: 193 Post(s)
Tagged: 2 Thread(s)
Quoted: 2935 Post(s)
Liked 2,932 Times
in
1,496 Posts
If you're just cleaning, don't bother. Clean them as best you can while there still firmly fixed in place.
I agree with the others though, some more informationa dn cleaner parts would help.
I agree with the others though, some more informationa dn cleaner parts would help.
__________________
“One morning you wake up, the girl is gone, the bikes are gone, all that's left behind is a pair of old tires and a tube of tubular glue, all squeezed out"
Sugar "Kane" Kowalczyk
“One morning you wake up, the girl is gone, the bikes are gone, all that's left behind is a pair of old tires and a tube of tubular glue, all squeezed out"
Sugar "Kane" Kowalczyk
#6
Senior Member
I would like to see the rest of the crank but I suspect it’s a Shimano FFS crank and its backwards Octa-joint bottom bracket. In order to remove the cups, you need an early Shimano freewheel tool, TL-FW20. These are rare but can be found. It fits the splines in the cups and they unscrew like other English-threaded cups: right side cup is left-hand threaded.
https://www.bikeforums.net/classic-v...kset-pics.html
https://velobase.com/ViewGroup.aspx?...3-dbe7b7f236eb
https://velobase.com/ViewComponent.a...e8875&Enum=115
https://www.google.com/url?sa=t&rct=...w&opi=89978449
Sorry for the ridiculous length of that last URL, but Google for some reason grossly obfuscates links in their current search results and I don't have the patience at present to interpret it down to more reasonable form. Also, while the Velobase entry for the crankset (third URL above) indicates a 22x1mm extractor is used, I think that's only for removing the crankarms. I believe this setup uses the same tool Jeff Willis indicates above for removing the FFS BB cups.
OP: Best of luck. If you're planning on restoring the bike to original and don't have the rest of the crankset parts, be advised that you might have difficulty finding the rest of the crankset. They're somewhat rare and very non-standard for the era. If you're not planning on a full restoration to original, destructive cup removal (as dddd suggests) is thus an option.
Last edited by Hondo6; 03-02-24 at 09:39 AM. Reason: Clarity and error correction.
Likes For Hondo6:
#7
Ride, Wrench, Swap, Race
Join Date: Jan 2010
Location: Northern California
Posts: 9,194
Bikes: Cheltenham-Pedersen racer, Boulder F/S Paris-Roubaix, Varsity racer, '52 Christophe, '62 Continental, '92 Merckx, '75 Limongi, '76 Presto, '72 Gitane SC, '71 Schwinn SS, etc.
Mentioned: 132 Post(s)
Tagged: 0 Thread(s)
Quoted: 1565 Post(s)
Liked 1,296 Times
in
866 Posts
One thing about replacing (or not replacing) lower-tier cranksets;
I have come to really like cranksets having a pants leg protector ring. I sometimes go to some length getting such rings to run true, even though that's not always as easy as it sounds.
Being able to jump on a bike without changing out of my lightweight trousers is how I get in about half of my rides these days, finding a hole in the rain forecast and/or making an errands run on any of the lesser bikes (i.e. the ones with such chainring guards and that can be left briefly unattended in public places).
Luckily I live in quite hilly terrain so even a short ride can involve challenging hills so I'm able to maintain some critical muscle mass despite an often busy schedule and/or iffy weather (today = Exhibit A and I've got to get back in time to watch the Daytona Supercross).
I'll try to update this post with a couple of photos of a typical such riding scenario (rain starts in three hours, so give me a couple of hours, lol).
I have come to really like cranksets having a pants leg protector ring. I sometimes go to some length getting such rings to run true, even though that's not always as easy as it sounds.
Being able to jump on a bike without changing out of my lightweight trousers is how I get in about half of my rides these days, finding a hole in the rain forecast and/or making an errands run on any of the lesser bikes (i.e. the ones with such chainring guards and that can be left briefly unattended in public places).
Luckily I live in quite hilly terrain so even a short ride can involve challenging hills so I'm able to maintain some critical muscle mass despite an often busy schedule and/or iffy weather (today = Exhibit A and I've got to get back in time to watch the Daytona Supercross).
I'll try to update this post with a couple of photos of a typical such riding scenario (rain starts in three hours, so give me a couple of hours, lol).
#8
Senior Member
Join Date: Apr 2007
Location: Thunder Bay, Ontario, Canada - burrrrr!
Posts: 11,674
Bikes: 1958 Rabeneick 120D, 1968 Legnano Gran Premio, 196? Torpado Professional, 2000 Marinoni Piuma
Mentioned: 210 Post(s)
Tagged: 0 Thread(s)
Quoted: 1372 Post(s)
Likes: 0
Liked 1,752 Times
in
939 Posts
Not sure if I have the right tool or not....
__________________
"98% of the bikes I buy are projects".
"98% of the bikes I buy are projects".
#9
Ride, Wrench, Swap, Race
Join Date: Jan 2010
Location: Northern California
Posts: 9,194
Bikes: Cheltenham-Pedersen racer, Boulder F/S Paris-Roubaix, Varsity racer, '52 Christophe, '62 Continental, '92 Merckx, '75 Limongi, '76 Presto, '72 Gitane SC, '71 Schwinn SS, etc.
Mentioned: 132 Post(s)
Tagged: 0 Thread(s)
Quoted: 1565 Post(s)
Liked 1,296 Times
in
866 Posts
Maybe this one? It fits the very first splined Shimano freewheels, and maybe just because it's early, it's not hollow like the similar one pictured above far right.
#10
Not so New