Replacement Trek head badge screws?
#1
Senior Member
Thread Starter
Replacement Trek head badge screws?
I’ve lost the small brass machine screws used to attach the screw on head badges. Anyone happen to know what size I need to pick up?
#2
Senior Member
Join Date: Mar 2013
Location: Maryland
Posts: 3,800
Bikes: Lots of English 3-speeds, a couple of old road bikes, 3 mountain bikes, 1 hybrid, and a couple of mash-ups
Mentioned: 53 Post(s)
Tagged: 0 Thread(s)
Quoted: 887 Post(s)
Liked 335 Times
in
225 Posts
Probably #2 x 1/8. McMaster Carr has them, but you'll need to buy a bunch. I have had no luck finding them at local hardware stores. You may want to try a local LBS that has been in business for a long time as well.
#3
SE Wis
Join Date: Apr 2005
Location: Milwaukee, WI
Posts: 10,517
Bikes: '68 Raleigh Sprite, '02 Raleigh C500, '84 Raleigh Gran Prix, '91 Trek 400, 2013 Novara Randonee, 1990 Trek 970
Mentioned: 40 Post(s)
Tagged: 0 Thread(s)
Quoted: 2747 Post(s)
Liked 3,401 Times
in
2,058 Posts
https://www.fasnetdirect.com/refguide...rewthreads.pdf
You can try by measuring the hole.
Tap and Drill Size Chart - American Fastener Technologies Corporation
I don't know about Trek but I have used both 4-40 & 2-56
If you can't find them in a "Good" hardware store try a gunsmith
You can try by measuring the hole.
Tap and Drill Size Chart - American Fastener Technologies Corporation
I don't know about Trek but I have used both 4-40 & 2-56
If you can't find them in a "Good" hardware store try a gunsmith
#4
Mr. Anachronism
Join Date: Jan 2013
Location: Somewhere west of Tobie's
Posts: 2,087
Bikes: fillet-brazed Chicago Schwinns, and some other stuff
Mentioned: 29 Post(s)
Tagged: 0 Thread(s)
Quoted: 526 Post(s)
Liked 256 Times
in
165 Posts
Yes, they're #2-56 x 1/8". I bought longer ones at Ace Hardware and cut them with a dremel cutoff wheel.
__________________
"My only true wisdom is in knowing I have none" -Socrates
"My only true wisdom is in knowing I have none" -Socrates
#5
Senior Member
Thread Starter
Awesome, thanks everyone. I’ll check out my local Ace tomorrow.
#6
Senior Member
Thread Starter
Looks like they only go to 4-40 at my local Ace. Looks like I’ll be ordering some.
#7
Mr. Anachronism
Join Date: Jan 2013
Location: Somewhere west of Tobie's
Posts: 2,087
Bikes: fillet-brazed Chicago Schwinns, and some other stuff
Mentioned: 29 Post(s)
Tagged: 0 Thread(s)
Quoted: 526 Post(s)
Liked 256 Times
in
165 Posts
At my local Ace, the "miniature" hardware is in a separate selection kit.
With that said, one advantage to ordering is that you can order the correct slotted-head brass screws. Ace only has stainless Phillips-head.
With that said, one advantage to ordering is that you can order the correct slotted-head brass screws. Ace only has stainless Phillips-head.
__________________
"My only true wisdom is in knowing I have none" -Socrates
"My only true wisdom is in knowing I have none" -Socrates
#8
Senior Member
Thread Starter
I saw the correct size stainless, but really wanted to stay with brass.
On that note, if anyone needs a few of these let me know.
On that note, if anyone needs a few of these let me know.
Thread
Thread Starter
Forum
Replies
Last Post
Digger Goreman
General Cycling Discussion
10
07-13-19 06:46 PM
thirteenthcor
General Cycling Discussion
2
07-29-18 02:10 PM