Help me spend $540!
#1
Junior Member
Thread Starter
Help me spend $540!
I haven't been on here in years, but have been riding my mom's custom bike that everyone was so helpful with before. The frame builder is still a mystery, but it is a custom 12-speed from the mid-1980's. Here's a picture!
Yesterday I discovered that, since I occasionally commute on this bike, I get $360 per calendar year to spend on bicycle-related things. I can use $180 before December 31, 2020 and another $360 any time in 2021. I don't want to spend much more than this in total, though I will get the benefit again in 2022.
So far I'm considering:
Yesterday I discovered that, since I occasionally commute on this bike, I get $360 per calendar year to spend on bicycle-related things. I can use $180 before December 31, 2020 and another $360 any time in 2021. I don't want to spend much more than this in total, though I will get the benefit again in 2022.
So far I'm considering:
- changing the 27" wheels to 700c's. Someone on here mentioned that the frame appears to have been built with 700c wheels in mind and I can't fully inflate my 27x1 Panaracer Paselas without a bit of rubbing while riding (this was not an issue with my mom's old tires and it doesn't rub when I'm not actually on the bike, so I know it's very close). I'm near Harris Cyclery and someone on the phone suggested one of these two wheelsets but I am open to anything in budget (most of my components are Shimano 600, so I would slightly prefer to match that if getting vintage). If it makes a difference, I weigh ~135 pounds and mostly ride on a MUP or in bike lanes
- related, does anyone know of any other 27" tires that might be less 'tall' than the Paselas so I can keep my wheels? They could probably be up to 1 1/4" wide if they were flatter
- rechroming the frame and fork as there is currently pitting/rust in a few places (especially the seat cluster). It seems like this will cost somewhere around $300
from my quick google - better lights (I still need to look into specific options -- I really only ride during the day in good weather, so this hasn't been a high priority)
- some sort of locking skewers (I currently remove the front wheel and lock everything up together if I'm worried, but that's obviously a bit inconvenient). It seems like a lot of these locking skewers are much longer than the rear triangle width on my bike -- would this be an issue?
- a lighter-weight lock for short lock-ups (I have a Kryptonite New York Standard currently, I'm thinking of getting the new Kryptonite Evolution LITE Mini-6)
#2
Bikes are okay, I guess.
Join Date: Jan 2015
Location: Richmond, Virginia
Posts: 6,938
Bikes: Waterford Paramount Touring, Giant CFM-2, Raleigh Sports 3-speeds in M23 & L23, Schwinn Cimarron oddball build, Marin Palisades Trail dropbar conversion, Nishiki Cresta GT
Mentioned: 69 Post(s)
Tagged: 0 Thread(s)
Quoted: 2647 Post(s)
Liked 2,446 Times
in
1,557 Posts
First, tell us the specifics of how we can get paid to upgrade our machines.
Likes For thumpism:
#3
(rhymes with spook)
Join Date: Aug 2009
Location: Winslow, AR
Posts: 2,788
Bikes: '83 univega gran turismo x2, '85 schwinn super le tour,'89 miyata triple cross, '91 GT tequesta, '90 yokota grizzly peak, '94 GT backwoods, '95'ish scott tampico, '98 bonty privateer, '93 mongoose crossway 625, '98 parkpre ariel, 2k'ish giant fcr3
Mentioned: 26 Post(s)
Tagged: 0 Thread(s)
Quoted: 919 Post(s)
Liked 745 Times
in
546 Posts
if 1" tires are rubbing, it might be a trial and error trying to work around picking tires to fit. perhaps the old ones just had less tread so they didn't rub? right now there's a vintage wheelset with 600 hubs and wolber alpin rims 700c on ebay for a bit over $100. i'll see if they're still available and post a link....for your considerations
edit: oops...they're matrix rims. still...600 hubs. black rims may not be what you're looking for, though
https://www.ebay.com/itm/Trek-Matrix...f9e3d2|iid%3A1
edit: oops...they're matrix rims. still...600 hubs. black rims may not be what you're looking for, though
https://www.ebay.com/itm/Trek-Matrix...f9e3d2|iid%3A1
#4
Senior Member
Join Date: Dec 2005
Posts: 17,156
Mentioned: 481 Post(s)
Tagged: 0 Thread(s)
Quoted: 3810 Post(s)
Liked 6,690 Times
in
2,610 Posts
I think either of those wheelsets would be fine. You might opt for 32mm Panaracer Pasela or smooth tread Gravel Kings, which should be in your budget. For a lightweight lock, I use an Ottolock cinch band: https://ottodesignworks.com/shop/ottolock
#5
(rhymes with spook)
Join Date: Aug 2009
Location: Winslow, AR
Posts: 2,788
Bikes: '83 univega gran turismo x2, '85 schwinn super le tour,'89 miyata triple cross, '91 GT tequesta, '90 yokota grizzly peak, '94 GT backwoods, '95'ish scott tampico, '98 bonty privateer, '93 mongoose crossway 625, '98 parkpre ariel, 2k'ish giant fcr3
Mentioned: 26 Post(s)
Tagged: 0 Thread(s)
Quoted: 919 Post(s)
Liked 745 Times
in
546 Posts
I think either of those wheelsets would be fine. You might opt for 32mm Panaracer Pasela or smooth tread Gravel Kings, which should be in your budget. For a lightweight lock, I use an Ottolock cinch band: https://ottodesignworks.com/shop/ottolock
#6
(rhymes with spook)
Join Date: Aug 2009
Location: Winslow, AR
Posts: 2,788
Bikes: '83 univega gran turismo x2, '85 schwinn super le tour,'89 miyata triple cross, '91 GT tequesta, '90 yokota grizzly peak, '94 GT backwoods, '95'ish scott tampico, '98 bonty privateer, '93 mongoose crossway 625, '98 parkpre ariel, 2k'ish giant fcr3
Mentioned: 26 Post(s)
Tagged: 0 Thread(s)
Quoted: 919 Post(s)
Liked 745 Times
in
546 Posts
maybe not 600 hubs, but they are shimano w/ silver rims...
https://www.ebay.com/itm/Late-1980-s...YAAOSw8WJfXQpj
https://www.ebay.com/itm/Late-1980-s...YAAOSw8WJfXQpj
#7
Senior Member
Join Date: May 2011
Location: Seattle WA
Posts: 2,841
Bikes: 2009 Handsome Devil, 1987 Trek 520 Cirrus, 1978 Motobecane Grand Touring, 1987 Nishiki Cresta GT, 1989 Specialized Allez Former bikes; 1986 Miyata Trail Runner, 1979 Miyata 912, 2011 VO Rando, 1999 Cannondale R800, 1986 Schwinn Passage
Mentioned: 72 Post(s)
Tagged: 0 Thread(s)
Quoted: 796 Post(s)
Liked 522 Times
in
367 Posts
Nice tires, ostrich Ortlieb bags for commuting some lights perhaps a front wheel built with a Dynamo hub if you are going to commute. and I hear good things about ABUS locks
Last edited by ryansu; 09-27-20 at 07:05 AM.
#8
Senior Member
Join Date: Jan 2015
Location: Los Angeles
Posts: 4,704
Bikes: 82 Medici, 2011 Richard Sachs, 2011 Milwaukee Road
Mentioned: 55 Post(s)
Tagged: 0 Thread(s)
Quoted: 1949 Post(s)
Liked 2,010 Times
in
1,109 Posts
Get Dura Ace 7400 hubs and some Shiny TB-14 rims And have the shop build them. Fun stuff.
__________________
I don't do: disks, tubeless, e-shifting, or bead head nymphs.
I don't do: disks, tubeless, e-shifting, or bead head nymphs.
Likes For Classtime:
#9
Senior Member
Join Date: Mar 2014
Location: City of Angels
Posts: 4,870
Bikes: A few too many
Mentioned: 42 Post(s)
Tagged: 1 Thread(s)
Quoted: 1364 Post(s)
Liked 2,180 Times
in
1,183 Posts
Here: https://www.bikeforums.net/classic-v...-original.html
Best, Ben
Opp's, I see you already bought a bike
Best, Ben
Opp's, I see you already bought a bike
Last edited by xiaoman1; 09-26-20 at 10:59 PM.
Likes For xiaoman1:
#11
WGB
Join Date: Jul 2017
Location: Niagara Region
Posts: 2,917
Bikes: Panasonic PT-4500
Mentioned: 46 Post(s)
Tagged: 0 Thread(s)
Quoted: 1800 Post(s)
Liked 2,334 Times
in
1,378 Posts
Watch your local advertising. 700c wheels are a dime a dozen (ok often $60). 700c offers options like using a wider and softer tire or maybe a better tread choice than 27s.
Due you have a co-op near you? It'd be a great resource and often a great source of bikes and parts and wheels. Might have a nice tubular wheelset, then no more riding to work, you can float.
Are you sure about re-chroming? A quality job will be north of $300. A bad job can destroy a frame. See hydrogen embrittlement on previous threads. You need a company that has bike specific experience.
If a commuter, why not consider powder coating? You don't have to spend it all....
Try Pinheads for locking skewers. They won't stop pros but they should prevent casual thieves. Often on sale on the ''Bay. Just have to carry the key or you're SOL if you get a flat.
Panniers? Might beat a back pack.
No downside to using lights in daylight. Reminds those other commuters (in cars) that you are there.
Due you have a co-op near you? It'd be a great resource and often a great source of bikes and parts and wheels. Might have a nice tubular wheelset, then no more riding to work, you can float.
Are you sure about re-chroming? A quality job will be north of $300. A bad job can destroy a frame. See hydrogen embrittlement on previous threads. You need a company that has bike specific experience.
If a commuter, why not consider powder coating? You don't have to spend it all....
Try Pinheads for locking skewers. They won't stop pros but they should prevent casual thieves. Often on sale on the ''Bay. Just have to carry the key or you're SOL if you get a flat.
Panniers? Might beat a back pack.
No downside to using lights in daylight. Reminds those other commuters (in cars) that you are there.
#12
Junior Member
Thread Starter
Thanks for the help so far! Any thoughts on this wheelset? I *think* my current bike is a freewheel and this looks like a casette - if so, would that be an issue? https://www.ebay.com/itm/Mavic-Open-...sAAOSw1PZfUBoo
Sorry, I should have specified that this is through my graduate school.
Sorry, I should have specified that this is through my graduate school.
I'm looking for silver, but will keep an eye out! I saw the 27" tires reference thread so will try to find a LBS that is willing to let me try without buying...
Thanks for that lock suggestion! It certainly looks light and portable enough!
I looked at Craigslist for 700c wheels and didn't see a lot yet but will keep an eye out - I think used bikes and bike parts tend to be pretty pricey in the Boston area. I'll check out the co-op, though! Thanks for the hydrogen embrittlement rechroming advice. It looks like Franklin Frames says $175 for just the fork -- I was originally going off of this price list from Quality Chrome Plating. I really like the chrome and have been able to (mostly!) stay on top of any new rust forming so don't feel the need to powdercoat yet. Any suggestions for New England chromers? I'll start digging into the framebuilders forum too.
Here's a photo of the clearance issue where you can also see the current overall state of the chrome:
Sorry, I should have specified that this is through my graduate school.
if 1" tires are rubbing, it might be a trial and error trying to work around picking tires to fit. perhaps the old ones just had less tread so they didn't rub? right now there's a vintage wheelset with 600 hubs and wolber alpin rims 700c on ebay for a bit over $100. i'll see if they're still available and post a link....for your considerations
edit: oops...they're matrix rims. still...600 hubs. black rims may not be what you're looking for, though
https://www.ebay.com/itm/Trek-Matrix...f9e3d2|iid%3A1
edit: oops...they're matrix rims. still...600 hubs. black rims may not be what you're looking for, though
https://www.ebay.com/itm/Trek-Matrix...f9e3d2|iid%3A1
I think either of those wheelsets would be fine. You might opt for 32mm Panaracer Pasela or smooth tread Gravel Kings, which should be in your budget. For a lightweight lock, I use an Ottolock cinch band: https://ottodesignworks.com/shop/ottolock
Watch your local advertising. 700c wheels are a dime a dozen (ok often $60). 700c offers options like using a wider and softer tire or maybe a better tread choice than 27s.
Due you have a co-op near you? It'd be a great resource and often a great source of bikes and parts and wheels. Might have a nice tubular wheelset, then no more riding to work, you can float.
Are you sure about re-chroming? A quality job will be north of $300. A bad job can destroy a frame. See hydrogen embrittlement on previous threads. You need a company that has bike specific experience.
If a commuter, why not consider powder coating? You don't have to spend it all....
Try Pinheads for locking skewers. They won't stop pros but they should prevent casual thieves. Often on sale on the ''Bay. Just have to carry the key or you're SOL if you get a flat.
Panniers? Might beat a back pack.
No downside to using lights in daylight. Reminds those other commuters (in cars) that you are there.
Due you have a co-op near you? It'd be a great resource and often a great source of bikes and parts and wheels. Might have a nice tubular wheelset, then no more riding to work, you can float.
Are you sure about re-chroming? A quality job will be north of $300. A bad job can destroy a frame. See hydrogen embrittlement on previous threads. You need a company that has bike specific experience.
If a commuter, why not consider powder coating? You don't have to spend it all....
Try Pinheads for locking skewers. They won't stop pros but they should prevent casual thieves. Often on sale on the ''Bay. Just have to carry the key or you're SOL if you get a flat.
Panniers? Might beat a back pack.
No downside to using lights in daylight. Reminds those other commuters (in cars) that you are there.
Here's a photo of the clearance issue where you can also see the current overall state of the chrome:
#13
Senior Member
Try rubbing wet aluminum foil on the chrome.
Your brake pads are high up in the brake calipers so this bike was likely intended to be 700c. To use the brakes on 700c wheels the pads will have to be lowered by 4mm. Looks like you can do this. The nice part is you can sell the old wheels to subsidize the new ones.
Cassette or freewheel doesnt matter but what matters is the rear spacing. You likely have 126mm spacing between the two rear dropouts. Some mid 80s cassette hubs had that spacing, otherwise everything new is going to be 130mm unless otherwise noted.
Your brake pads are high up in the brake calipers so this bike was likely intended to be 700c. To use the brakes on 700c wheels the pads will have to be lowered by 4mm. Looks like you can do this. The nice part is you can sell the old wheels to subsidize the new ones.
Cassette or freewheel doesnt matter but what matters is the rear spacing. You likely have 126mm spacing between the two rear dropouts. Some mid 80s cassette hubs had that spacing, otherwise everything new is going to be 130mm unless otherwise noted.
#14
Edumacator
Join Date: Jan 2018
Location: Goose Creek, SC
Posts: 6,803
Bikes: '87 Crestdale, '87 Basso Gap, '92 Rossin Performance EL-OS, 1990 VanTuyl, 1980s Losa, 1985 Trek 670, 1982 AD SLE, 1987 PX10, etc...
Mentioned: 59 Post(s)
Tagged: 0 Thread(s)
Quoted: 2439 Post(s)
Liked 3,122 Times
in
1,964 Posts
What is the O.L.D. of the rear hub? 130 or 126?
are the hubs Shimano 600 EX as well?
Is the drivetrain (rear and front derailleurs, crank and freewheel) 600 EX as well? 6 speed?
are the hubs Shimano 600 EX as well?
Is the drivetrain (rear and front derailleurs, crank and freewheel) 600 EX as well? 6 speed?
__________________
1987 Crest Cannondale, 1987 Basso Gap, 1992 Rossin Performance EL, 1990ish Van Tuyl, 1985 Trek 670, 1982 AD SLE, 2003 Pinarello Surprise, 1990ish MBK Atlantique, 1987 Peugeot Competition, 1987 Nishiki Tri-A, 1981 Faggin, 1996 Cannondale M500, 1984 Mercian, 1982 AD SuperLeicht, 1985 Massi (model unknown), 1988 Daccordi Griffe , 1989 Fauxsin MTB, 1981 Ciocc Mockba, 1992 Bianchi Giro, 1977 Colnago Super
1987 Crest Cannondale, 1987 Basso Gap, 1992 Rossin Performance EL, 1990ish Van Tuyl, 1985 Trek 670, 1982 AD SLE, 2003 Pinarello Surprise, 1990ish MBK Atlantique, 1987 Peugeot Competition, 1987 Nishiki Tri-A, 1981 Faggin, 1996 Cannondale M500, 1984 Mercian, 1982 AD SuperLeicht, 1985 Massi (model unknown), 1988 Daccordi Griffe , 1989 Fauxsin MTB, 1981 Ciocc Mockba, 1992 Bianchi Giro, 1977 Colnago Super
#15
WGB
Join Date: Jul 2017
Location: Niagara Region
Posts: 2,917
Bikes: Panasonic PT-4500
Mentioned: 46 Post(s)
Tagged: 0 Thread(s)
Quoted: 1800 Post(s)
Liked 2,334 Times
in
1,378 Posts
+1 on Narhay's comment about foil. Most of us have or have had bikes with a lot worse chrome issues. If that's your idea of bad I see no worries.
Aluminum foil is softer than chrome but harder than rust. A little WD-40 on the chrome and then a light polish with foil. Alternatively, buy some Evaporust and strip bike down, if you don't have tools that's where the Co-op come in. Soak the brakes and any other rusted components in a container of Evaporust overnight. Soak the forks the same way. If there is chrome on the rear, say the chain stays soak a rag in Evaporust and wrap tightly around the rusted area and then re-wrap with plastic wrap and leave over night. You may still have a bit of rust in a few places but the polish method should then get it fine. The good thing about this method is that you will know when the grease and bearings were last replaced. After you are done, use a good car wax and wax the frame and forks. Just like with a car, it'll protect your bike.
Aluminum foil is softer than chrome but harder than rust. A little WD-40 on the chrome and then a light polish with foil. Alternatively, buy some Evaporust and strip bike down, if you don't have tools that's where the Co-op come in. Soak the brakes and any other rusted components in a container of Evaporust overnight. Soak the forks the same way. If there is chrome on the rear, say the chain stays soak a rag in Evaporust and wrap tightly around the rusted area and then re-wrap with plastic wrap and leave over night. You may still have a bit of rust in a few places but the polish method should then get it fine. The good thing about this method is that you will know when the grease and bearings were last replaced. After you are done, use a good car wax and wax the frame and forks. Just like with a car, it'll protect your bike.
#16
WGB
Join Date: Jul 2017
Location: Niagara Region
Posts: 2,917
Bikes: Panasonic PT-4500
Mentioned: 46 Post(s)
Tagged: 0 Thread(s)
Quoted: 1800 Post(s)
Liked 2,334 Times
in
1,378 Posts
duplicate
#18
Senior Member
Join Date: Dec 2005
Posts: 17,156
Mentioned: 481 Post(s)
Tagged: 0 Thread(s)
Quoted: 3810 Post(s)
Liked 6,690 Times
in
2,610 Posts
I don’t know of New England chromers, but the motorcycle folks might. You could ask at Pike’s Powder Coating in Alston as they do a variety of objects that might require chrome. On local co-ops that sell wheels, Broadway Bikes in Somerville or Bikes Not Bombs in JP are two excellent resources.
#19
Senior Member
Join Date: Dec 2005
Posts: 17,156
Mentioned: 481 Post(s)
Tagged: 0 Thread(s)
Quoted: 3810 Post(s)
Liked 6,690 Times
in
2,610 Posts
Also, that $360/year bicycle benefit is a federal program: https://bikeleague.org/content/bicycle-commuter-benefit
My former employer participated, but my current one does not, unfortunately.
My former employer participated, but my current one does not, unfortunately.
Likes For nlerner:
#20
Junior Member
Thread Starter
When I took the wheel off and measured the frame, the inside dimension in the rear triangle is 125mm.
Try rubbing wet aluminum foil on the chrome.
Your brake pads are high up in the brake calipers so this bike was likely intended to be 700c. To use the brakes on 700c wheels the pads will have to be lowered by 4mm. Looks like you can do this. The nice part is you can sell the old wheels to subsidize the new ones.
Cassette or freewheel doesnt matter but what matters is the rear spacing. You likely have 126mm spacing between the two rear dropouts. Some mid 80s cassette hubs had that spacing, otherwise everything new is going to be 130mm unless otherwise noted.
Your brake pads are high up in the brake calipers so this bike was likely intended to be 700c. To use the brakes on 700c wheels the pads will have to be lowered by 4mm. Looks like you can do this. The nice part is you can sell the old wheels to subsidize the new ones.
Cassette or freewheel doesnt matter but what matters is the rear spacing. You likely have 126mm spacing between the two rear dropouts. Some mid 80s cassette hubs had that spacing, otherwise everything new is going to be 130mm unless otherwise noted.
+1 on Narhay's comment about foil. Most of us have or have had bikes with a lot worse chrome issues. If that's your idea of bad I see no worries.
Aluminum foil is softer than chrome but harder than rust. A little WD-40 on the chrome and then a light polish with foil. Alternatively, buy some Evaporust and strip bike down, if you don't have tools that's where the Co-op come in. Soak the brakes and any other rusted components in a container of Evaporust overnight. Soak the forks the same way. If there is chrome on the rear, say the chain stays soak a rag in Evaporust and wrap tightly around the rusted area and then re-wrap with plastic wrap and leave over night. You may still have a bit of rust in a few places but the polish method should then get it fine. The good thing about this method is that you will know when the grease and bearings were last replaced. After you are done, use a good car wax and wax the frame and forks. Just like with a car, it'll protect your bike.
Aluminum foil is softer than chrome but harder than rust. A little WD-40 on the chrome and then a light polish with foil. Alternatively, buy some Evaporust and strip bike down, if you don't have tools that's where the Co-op come in. Soak the brakes and any other rusted components in a container of Evaporust overnight. Soak the forks the same way. If there is chrome on the rear, say the chain stays soak a rag in Evaporust and wrap tightly around the rusted area and then re-wrap with plastic wrap and leave over night. You may still have a bit of rust in a few places but the polish method should then get it fine. The good thing about this method is that you will know when the grease and bearings were last replaced. After you are done, use a good car wax and wax the frame and forks. Just like with a car, it'll protect your bike.
#21
Edumacator
Join Date: Jan 2018
Location: Goose Creek, SC
Posts: 6,803
Bikes: '87 Crestdale, '87 Basso Gap, '92 Rossin Performance EL-OS, 1990 VanTuyl, 1980s Losa, 1985 Trek 670, 1982 AD SLE, 1987 PX10, etc...
Mentioned: 59 Post(s)
Tagged: 0 Thread(s)
Quoted: 2439 Post(s)
Liked 3,122 Times
in
1,964 Posts
Wheels would be a good upgrade then. As other have stated, looking on FB Marketplace or CL might net a solid pair.
...if the clearance allows, maybe some fenders?
...definitely lights are always a good investment for dusk rides...
...and a decent lock and you’re set!
For reference, I picked up a pair of 700c MA 40 laced to Dura Ace hubs for $75 last year.
...if the clearance allows, maybe some fenders?
...definitely lights are always a good investment for dusk rides...
...and a decent lock and you’re set!
For reference, I picked up a pair of 700c MA 40 laced to Dura Ace hubs for $75 last year.
__________________
1987 Crest Cannondale, 1987 Basso Gap, 1992 Rossin Performance EL, 1990ish Van Tuyl, 1985 Trek 670, 1982 AD SLE, 2003 Pinarello Surprise, 1990ish MBK Atlantique, 1987 Peugeot Competition, 1987 Nishiki Tri-A, 1981 Faggin, 1996 Cannondale M500, 1984 Mercian, 1982 AD SuperLeicht, 1985 Massi (model unknown), 1988 Daccordi Griffe , 1989 Fauxsin MTB, 1981 Ciocc Mockba, 1992 Bianchi Giro, 1977 Colnago Super
1987 Crest Cannondale, 1987 Basso Gap, 1992 Rossin Performance EL, 1990ish Van Tuyl, 1985 Trek 670, 1982 AD SLE, 2003 Pinarello Surprise, 1990ish MBK Atlantique, 1987 Peugeot Competition, 1987 Nishiki Tri-A, 1981 Faggin, 1996 Cannondale M500, 1984 Mercian, 1982 AD SuperLeicht, 1985 Massi (model unknown), 1988 Daccordi Griffe , 1989 Fauxsin MTB, 1981 Ciocc Mockba, 1992 Bianchi Giro, 1977 Colnago Super
#22
(rhymes with spook)
Join Date: Aug 2009
Location: Winslow, AR
Posts: 2,788
Bikes: '83 univega gran turismo x2, '85 schwinn super le tour,'89 miyata triple cross, '91 GT tequesta, '90 yokota grizzly peak, '94 GT backwoods, '95'ish scott tampico, '98 bonty privateer, '93 mongoose crossway 625, '98 parkpre ariel, 2k'ish giant fcr3
Mentioned: 26 Post(s)
Tagged: 0 Thread(s)
Quoted: 919 Post(s)
Liked 745 Times
in
546 Posts
that's interesting. what does the clearance look like for the tire in the rear? i had an early/mid 80's lotus elite that had short reach clearance in the fork, but standard clearance in the rear. however, it was definitely designed for 27" wheels. atleast, that's what it equipped with in the catalogue spec. but, i could not fit more than a 1" tire in the fork and still clear the brake. perhaps your frame is the same in that regard?
#23
multimodal commuter
Join Date: Nov 2006
Location: NJ, NYC, LI
Posts: 19,808
Bikes: 1940s Fothergill, 1959 Allegro Special, 1963? Claud Butler Olympic Sprint, Lambert 'Clubman', 1974 Fuji "the Ace", 1976 Holdsworth 650b conversion rando bike, 1983 Trek 720 tourer, 1984 Counterpoint Opus II, 1993 Basso Gap, 2010 Downtube 8h, and...
Mentioned: 584 Post(s)
Tagged: 0 Thread(s)
Quoted: 1908 Post(s)
Liked 574 Times
in
339 Posts
If new wheels are more or less a given , you might also consider 650b wheels. You'll need brakes...
__________________
www.rhmsaddles.com.
www.rhmsaddles.com.
#24
Senior Member
You could buy something like this Rockhopper, put street tires and fenders on it, maybe upright bars and a basket. Arguably a better commuter platform than what you have, depending on your circumstances and needs.