Ok, what model Peugeot is this:
#1
Senior Member
Thread Starter
Join Date: Feb 2020
Posts: 2,826
Mentioned: 49 Post(s)
Tagged: 0 Thread(s)
Quoted: 1109 Post(s)
Likes: 0
Liked 1,329 Times
in
785 Posts
Ok, what model Peugeot is this:
Looks like the PF60 in the 1982 US brochure on bikeboompeugeot.com, BUT this one has Mafac cantilever brakes, and the bars are Phillippe, and the crank is branded Peugeot (rings say stronglight) - and it goes 28-40-52 not 32-42-52 as in the brouchure...not that I'm complaining...
Everything looks original to me, Helicomatic with a 30-tooth big cog, Weinmann levers, Rigida eyeletted rims. Pedals will need work, does anyone have the caps for these (I need both).
Pics as received:
Everything looks original to me, Helicomatic with a 30-tooth big cog, Weinmann levers, Rigida eyeletted rims. Pedals will need work, does anyone have the caps for these (I need both).
Pics as received:
#2
PM me your cotters
Join Date: Jun 2015
Location: ATL
Posts: 3,241
Mentioned: 80 Post(s)
Tagged: 0 Thread(s)
Quoted: 1137 Post(s)
Liked 590 Times
in
422 Posts
Decals would put it more in the early-mid 80s. We could really use to know the number stamped into the bottom bracket so we can iron out the date.
But I will say, if memory recalls, outside of the MTB/ATB bikes, the Vagabond should've been roughly equipped the same.
But I will say, if memory recalls, outside of the MTB/ATB bikes, the Vagabond should've been roughly equipped the same.
__________________
███████████████
███████████████
#4
Phyllo-buster
Join Date: Jan 2010
Location: Nova Scotia
Posts: 8,848
Bikes: roadsters, club bikes, fixed and classic
Mentioned: 133 Post(s)
Tagged: 0 Thread(s)
Quoted: 2298 Post(s)
Liked 2,056 Times
in
1,256 Posts
Looks a lot like the Centenary we saw recently. '82?
Without the Aero shifters of course. And cantis?
Without the Aero shifters of course. And cantis?
#5
PM me your cotters
Join Date: Jun 2015
Location: ATL
Posts: 3,241
Mentioned: 80 Post(s)
Tagged: 0 Thread(s)
Quoted: 1137 Post(s)
Liked 590 Times
in
422 Posts
Actually, if Vitus, it's PF-something if we follow Peugeot's standards with regard to PF/PV/PSV
__________________
███████████████
███████████████
Last edited by francophile; 10-08-20 at 05:31 PM.
Likes For francophile:
#7
PM me your cotters
Join Date: Jun 2015
Location: ATL
Posts: 3,241
Mentioned: 80 Post(s)
Tagged: 0 Thread(s)
Quoted: 1137 Post(s)
Liked 590 Times
in
422 Posts
Yeah, you got me on this one. There were a number of PFxx and PFNxx models. At least we know definitively the date of the frame, you should find the hubs, seat post and stem share an '82 or '83 date due to how closely the frame manufacture was to the 82/83 cusp.
__________________
███████████████
███████████████
#8
Senior Member
Join Date: Nov 2015
Posts: 4,490
Mentioned: 102 Post(s)
Tagged: 0 Thread(s)
Quoted: 1641 Post(s)
Likes: 0
Liked 832 Times
in
540 Posts
Decals are typical to 1983 models......
__________________
72 Line Seeker
83 Davidson Signature
84 Peugeot PSV
84 Peugeot PY10FC
84 Gitane Tour de France.
85 Vitus Plus Carbone 7
86 ALAN Record Carbonio
86 Medici Aerodynamic (Project)
88 Pinarello Montello
89 Bottecchia Professional Chorus SL
95 Trek 5500 OCLV (Project)
72 Line Seeker
83 Davidson Signature
84 Peugeot PSV
84 Peugeot PY10FC
84 Gitane Tour de France.
85 Vitus Plus Carbone 7
86 ALAN Record Carbonio
86 Medici Aerodynamic (Project)
88 Pinarello Montello
89 Bottecchia Professional Chorus SL
95 Trek 5500 OCLV (Project)
Likes For Chombi1:
#9
Hoards Thumbshifters
Join Date: Jul 2010
Location: Signal Mountain, TN
Posts: 1,157
Bikes: '23 Black Mtn MC, '87 Bruce Gordon Chinook, '08 Jamis Aurora, '86 Trek 560, '97 Mongoose Rockadile, & '91 Trek 750
Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 246 Post(s)
Liked 338 Times
in
193 Posts
I'm the least qualified for this...
... but could it be an early cyclocross example? Notice no mounts really for racks, just mounts for mud guards. I've seen Pinarello's with similar brakes during that time.
Again, way out of my expertise area.
Again, way out of my expertise area.
#10
Hoards Thumbshifters
Join Date: Jul 2010
Location: Signal Mountain, TN
Posts: 1,157
Bikes: '23 Black Mtn MC, '87 Bruce Gordon Chinook, '08 Jamis Aurora, '86 Trek 560, '97 Mongoose Rockadile, & '91 Trek 750
Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 246 Post(s)
Liked 338 Times
in
193 Posts
1983 PH60? I have found earlier examples of the PH60 with Cantilevers...
#12
Senior Member
Thread Starter
Join Date: Feb 2020
Posts: 2,826
Mentioned: 49 Post(s)
Tagged: 0 Thread(s)
Quoted: 1109 Post(s)
Likes: 0
Liked 1,329 Times
in
785 Posts
Ok, started taking it apart; there is good news and there is bad news.
Good news - everything is threaded english.
Bad - stuck seatpost.
frame is now upside down and penetrating oil being applied throuigh the BB shell (that's how I know it's english).
Edit: fork is 25mm and French. Tant pis, c'est normal.
Edit again, not english, swiss (see below).
Good news - everything is threaded english.
Bad - stuck seatpost.
frame is now upside down and penetrating oil being applied throuigh the BB shell (that's how I know it's english).
Edit: fork is 25mm and French. Tant pis, c'est normal.
Edit again, not english, swiss (see below).
Last edited by oneclick; 10-12-20 at 09:24 AM.
#13
Senior Member
Thread Starter
Join Date: Feb 2020
Posts: 2,826
Mentioned: 49 Post(s)
Tagged: 0 Thread(s)
Quoted: 1109 Post(s)
Likes: 0
Liked 1,329 Times
in
785 Posts
This bike is seeming more and more like floor sweepings. I've looked at every 1980 to 1985 catalog on bikeboompeugeot, at pages & pages of google images for various searches involving combinations of vitus/peugeot/cantilever/touring/randonneur/etcetera, nothing matches. Cantilevers and a Vitus frame and a triple crankset - a wider triple than anything in the brochures; and pretty much surely 1983.
No paper label.
No paper label.
#14
Senior Member
Join Date: May 2011
Location: Seattle WA
Posts: 2,841
Bikes: 2009 Handsome Devil, 1987 Trek 520 Cirrus, 1978 Motobecane Grand Touring, 1987 Nishiki Cresta GT, 1989 Specialized Allez Former bikes; 1986 Miyata Trail Runner, 1979 Miyata 912, 2011 VO Rando, 1999 Cannondale R800, 1986 Schwinn Passage
Mentioned: 72 Post(s)
Tagged: 0 Thread(s)
Quoted: 796 Post(s)
Liked 522 Times
in
367 Posts
The important stuff - does it fit? how does it ride? good luck with the seat post
Likes For ryansu:
#15
Senior Member
Thread Starter
Join Date: Feb 2020
Posts: 2,826
Mentioned: 49 Post(s)
Tagged: 0 Thread(s)
Quoted: 1109 Post(s)
Likes: 0
Liked 1,329 Times
in
785 Posts
After finding the fork was metric I started measuring and checking things again.
Tubes are metric - Steerer 25mm, seat and down 28.1 (paint) and top 26.1 (again paint).
And that adjustable cup that came out nice and easy left-handed? Not English, it's SWISS, both cups are metric.
What the hell have I got here?
Tubes are metric - Steerer 25mm, seat and down 28.1 (paint) and top 26.1 (again paint).
And that adjustable cup that came out nice and easy left-handed? Not English, it's SWISS, both cups are metric.
What the hell have I got here?
#16
Ride, Wrench, Swap, Race
Join Date: Jan 2010
Location: Northern California
Posts: 9,194
Bikes: Cheltenham-Pedersen racer, Boulder F/S Paris-Roubaix, Varsity racer, '52 Christophe, '62 Continental, '92 Merckx, '75 Limongi, '76 Presto, '72 Gitane SC, '71 Schwinn SS, etc.
Mentioned: 132 Post(s)
Tagged: 0 Thread(s)
Quoted: 1565 Post(s)
Liked 1,296 Times
in
866 Posts
Chainstays look short, so looking more like a cyclocross model than any touring bike.
But a cyclocross bike doesn't typically have a triple. I use a triple for CX so that the chain has a good place to fall if it does fall off the small ring.
But a cyclocross bike doesn't typically have a triple. I use a triple for CX so that the chain has a good place to fall if it does fall off the small ring.
#18
Senior Member
Thread Starter
Join Date: Feb 2020
Posts: 2,826
Mentioned: 49 Post(s)
Tagged: 0 Thread(s)
Quoted: 1109 Post(s)
Likes: 0
Liked 1,329 Times
in
785 Posts
More measurements - 126mm rear, frame weighs 4.6 lbs, for 1.7 lbs, Seat post is 26.3-ish (got the damm thing out, had quite a crust of corrosion on it, might have made it a bit smaller cleaning all that off).
That's a pretty light frame for steel-not-high-end, I'm happy, except now I don't know what to do with it. It's too big for me, I already have a tourer.
It's a shame to part it out - it's in fabulous shape and everything matches - but who would buy it whole, with all the oddities - swiss BB, french steerer,metric tubes, cantis - plus shipping form here?
That's a pretty light frame for steel-not-high-end, I'm happy, except now I don't know what to do with it. It's too big for me, I already have a tourer.
It's a shame to part it out - it's in fabulous shape and everything matches - but who would buy it whole, with all the oddities - swiss BB, french steerer,metric tubes, cantis - plus shipping form here?
#19
feros ferio
Join Date: Jul 2000
Location: www.ci.encinitas.ca.us
Posts: 21,804
Bikes: 1959 Capo Modell Campagnolo; 1960 Capo Sieger (2); 1962 Carlton Franco Suisse; 1970 Peugeot UO-8; 1982 Bianchi Campione d'Italia; 1988 Schwinn Project KOM-10;
Mentioned: 44 Post(s)
Tagged: 0 Thread(s)
Quoted: 1393 Post(s)
Liked 1,334 Times
in
840 Posts
After finding the fork was metric I started measuring and checking things again.
Tubes are metric - Steerer 25mm, seat and down 28.1 (paint) and top 26.1 (again paint).
And that adjustable cup that came out nice and easy left-handed? Not English, it's SWISS, both cups are metric.
What the hell have I got here?
Tubes are metric - Steerer 25mm, seat and down 28.1 (paint) and top 26.1 (again paint).
And that adjustable cup that came out nice and easy left-handed? Not English, it's SWISS, both cups are metric.
What the hell have I got here?
__________________
"Far and away the best prize that life offers is the chance to work hard at work worth doing." --Theodore Roosevelt
Capo: 1959 Modell Campagnolo, S/N 40324; 1960 Sieger (2), S/N 42624, 42597
Carlton: 1962 Franco Suisse, S/N K7911
Peugeot: 1970 UO-8, S/N 0010468
Bianchi: 1982 Campione d'Italia, S/N 1.M9914
Schwinn: 1988 Project KOM-10, S/N F804069
"Far and away the best prize that life offers is the chance to work hard at work worth doing." --Theodore Roosevelt
Capo: 1959 Modell Campagnolo, S/N 40324; 1960 Sieger (2), S/N 42624, 42597
Carlton: 1962 Franco Suisse, S/N K7911
Peugeot: 1970 UO-8, S/N 0010468
Bianchi: 1982 Campione d'Italia, S/N 1.M9914
Schwinn: 1988 Project KOM-10, S/N F804069
#20
feros ferio
Join Date: Jul 2000
Location: www.ci.encinitas.ca.us
Posts: 21,804
Bikes: 1959 Capo Modell Campagnolo; 1960 Capo Sieger (2); 1962 Carlton Franco Suisse; 1970 Peugeot UO-8; 1982 Bianchi Campione d'Italia; 1988 Schwinn Project KOM-10;
Mentioned: 44 Post(s)
Tagged: 0 Thread(s)
Quoted: 1393 Post(s)
Liked 1,334 Times
in
840 Posts
More measurements - 126mm rear, frame weighs 4.6 lbs, for 1.7 lbs, Seat post is 26.3-ish (got the damm thing out, had quite a crust of corrosion on it, might have made it a bit smaller cleaning all that off).
That's a pretty light frame for steel-not-high-end, I'm happy, except now I don't know what to do with it. It's too big for me, I already have a tourer.
It's a shame to part it out - it's in fabulous shape and everything matches - but who would buy it whole, with all the oddities - swiss BB, french steerer,metric tubes, cantis - plus shipping form here?
That's a pretty light frame for steel-not-high-end, I'm happy, except now I don't know what to do with it. It's too big for me, I already have a tourer.
It's a shame to part it out - it's in fabulous shape and everything matches - but who would buy it whole, with all the oddities - swiss BB, french steerer,metric tubes, cantis - plus shipping form here?
Nice find!
The deviation between your chainring sizes and those in the catalog could just be the result of a bit of "gear freaking" or customization on the part of an earlier owner, or just a substitution at the factory because of a parts shortage. I have routinely regeared every bicycle I have owned, to meet my own needs -- there is absolutely nothing sacred about catalog-listed tooth counts on either the crank or the rear axle.
__________________
"Far and away the best prize that life offers is the chance to work hard at work worth doing." --Theodore Roosevelt
Capo: 1959 Modell Campagnolo, S/N 40324; 1960 Sieger (2), S/N 42624, 42597
Carlton: 1962 Franco Suisse, S/N K7911
Peugeot: 1970 UO-8, S/N 0010468
Bianchi: 1982 Campione d'Italia, S/N 1.M9914
Schwinn: 1988 Project KOM-10, S/N F804069
"Far and away the best prize that life offers is the chance to work hard at work worth doing." --Theodore Roosevelt
Capo: 1959 Modell Campagnolo, S/N 40324; 1960 Sieger (2), S/N 42624, 42597
Carlton: 1962 Franco Suisse, S/N K7911
Peugeot: 1970 UO-8, S/N 0010468
Bianchi: 1982 Campione d'Italia, S/N 1.M9914
Schwinn: 1988 Project KOM-10, S/N F804069
#21
Senior Member
Join Date: Nov 2004
Posts: 23,223
Mentioned: 655 Post(s)
Tagged: 1 Thread(s)
Quoted: 4722 Post(s)
Likes: 0
Liked 3,039 Times
in
1,877 Posts
I checked my Canadian market literature and there was nothing with cantilevers in 1983 (or 1982 and 1984).
#23
Senior Member
Thread Starter
Join Date: Feb 2020
Posts: 2,826
Mentioned: 49 Post(s)
Tagged: 0 Thread(s)
Quoted: 1109 Post(s)
Likes: 0
Liked 1,329 Times
in
785 Posts
This might well be an import, from what I remember of the conversation with the seller (left behind in an apt complex by departed foreign tenants, after <n> months stuff gets sold).