Trouble with Saris M2 smart trainer
01-13-21, 06:41 PM
#1
Newbie
Thread Starter
Join Date: Jan 2021
Posts: 4
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 2 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Trouble with Saris M2 smart trainer
I recently purchased an M2 smart trainer. When the resistance goes up, it becomes very inconsistent in that
every down stroke is followed by a sharp jump in resistance. Its not riding smoothly. Its gets better as I go to
lower gears, but I have to go to such a low gear to get it to smooth out that Im not getting a work out. Any ideas?
every down stroke is followed by a sharp jump in resistance. Its not riding smoothly. Its gets better as I go to
lower gears, but I have to go to such a low gear to get it to smooth out that Im not getting a work out. Any ideas?
01-19-21, 02:39 PM
#2
Senior Member
Join Date: Jan 2020
Location: Altadena, CA
Posts: 420
Bikes: 2018 Storck Fascenario.3 Platinum, 2003 Time VX Special Pro, 1977 Nishiki ONP, 1999 Trek 9900 Team Issue
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 175 Post(s)
Liked 396 Times
in
191 Posts
Originally Posted by irazvi
I recently purchased an M2 smart trainer. When the resistance goes up, it becomes very inconsistent in that
every down stroke is followed by a sharp jump in resistance. Its not riding smoothly. Its gets better as I go to
lower gears, but I have to go to such a low gear to get it to smooth out that Im not getting a work out. Any ideas?
every down stroke is followed by a sharp jump in resistance. Its not riding smoothly. Its gets better as I go to
lower gears, but I have to go to such a low gear to get it to smooth out that Im not getting a work out. Any ideas?
01-19-21, 02:52 PM
#3
Newbie
Thread Starter
Join Date: Jan 2021
Posts: 4
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 2 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Thanks,
I will try that. Im also having trouble calibrating it. It gives me an error when I try. I would think this could also be at the heart of it.
did you have that problem as well?
I will try that. Im also having trouble calibrating it. It gives me an error when I try. I would think this could also be at the heart of it.
did you have that problem as well?
01-19-21, 03:16 PM
#4
Senior Member
Join Date: Jan 2020
Location: Altadena, CA
Posts: 420
Bikes: 2018 Storck Fascenario.3 Platinum, 2003 Time VX Special Pro, 1977 Nishiki ONP, 1999 Trek 9900 Team Issue
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 175 Post(s)
Liked 396 Times
in
191 Posts
Originally Posted by irazvi
Thanks,
I will try that. Im also having trouble calibrating it. It gives me an error when I try. I would think this could also be at the heart of it.
did you have that problem as well?
I will try that. Im also having trouble calibrating it. It gives me an error when I try. I would think this could also be at the heart of it.
did you have that problem as well?
01-19-21, 03:19 PM
#5
Newbie
Thread Starter
Join Date: Jan 2021
Posts: 4
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 2 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Originally Posted by Eric F
I have found that calibrating with the app needs me to turn off all other connections to the trainer (Zwift and Zwift Companion, in my case). There have been a couple of times where turning off (unplugging) the trainer for a bit seemed to help.
Thanks!
01-20-21, 05:51 AM
#6
Newbie
Thread Starter
Join Date: Jan 2021
Posts: 4
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 2 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
So I checked and the firmware is up to date. I tried calibrating with no other connections. This time I did not get an error, but it
never completed. I tried for about 5-10 minutes (?) and it never ended. How long does it usually take? So Im still stuck with
the same problem of un even resistance.
Thanks
never completed. I tried for about 5-10 minutes (?) and it never ended. How long does it usually take? So Im still stuck with
the same problem of un even resistance.
Thanks
