A trick to replacing campy pads?
#1
Edumacator
Thread Starter
Join Date: Jan 2018
Location: Goose Creek, SC
Posts: 6,807
Bikes: '87 Crestdale, '87 Basso Gap, '92 Rossin Performance EL-OS, 1990 VanTuyl, 1980s Losa, 1985 Trek 670, 1982 AD SLE, 1987 PX10, etc...
Mentioned: 59 Post(s)
Tagged: 0 Thread(s)
Quoted: 2439 Post(s)
Liked 3,128 Times
in
1,967 Posts
A trick to replacing campy pads?
Earlier Chorus dual pivots (BR 14RE clone) with metal holders...is there a trick to removing the pads and installing the koolstop salmon C89??
__________________
1987 Crest Cannondale, 1987 Basso Gap, 1992 Rossin Performance EL, 1990ish Van Tuyl, 1985 Trek 670, 1982 AD SLE, 2003 Pinarello Surprise, 1990ish MBK Atlantique, 1987 Peugeot Competition, 1987 Nishiki Tri-A, 1981 Faggin, 1996 Cannondale M500, 1984 Mercian, 1982 AD SuperLeicht, 1985 Massi (model unknown), 1988 Daccordi Griffe , 1989 Fauxsin MTB, 1981 Ciocc Mockba, 1992 Bianchi Giro, 1977 Colnago Super
1987 Crest Cannondale, 1987 Basso Gap, 1992 Rossin Performance EL, 1990ish Van Tuyl, 1985 Trek 670, 1982 AD SLE, 2003 Pinarello Surprise, 1990ish MBK Atlantique, 1987 Peugeot Competition, 1987 Nishiki Tri-A, 1981 Faggin, 1996 Cannondale M500, 1984 Mercian, 1982 AD SuperLeicht, 1985 Massi (model unknown), 1988 Daccordi Griffe , 1989 Fauxsin MTB, 1981 Ciocc Mockba, 1992 Bianchi Giro, 1977 Colnago Super
#2
Senior Member
Join Date: May 2019
Location: Bloomington, IN
Posts: 2,949
Bikes: Paramount, Faggin, Ochsner, Ciocc, Basso
Mentioned: 117 Post(s)
Tagged: 0 Thread(s)
Quoted: 1303 Post(s)
Liked 1,911 Times
in
1,141 Posts
Try a pair of channel lock pliers. Always worked for me. Smiles, MH
#3
Senior Member
Join Date: Dec 2014
Location: Central Virginia
Posts: 4,780
Bikes: Numerous
Mentioned: 150 Post(s)
Tagged: 0 Thread(s)
Quoted: 1678 Post(s)
Liked 3,098 Times
in
914 Posts
I usually use wide jaw pliers with one jaw on the lip of the holder at the open end and the other jaw on the other end of the pad. Squeeze and viola! To install, lots of times I’ll put a drop of lube and then either do the reverse with the pliers or press the pad in with a bench vise.
__________________
N = '96 Colnago C40, '04 Wilier Alpe D'Huez, '10 Colnago EPS, '85 Merckx Pro, '89 Merckx Century, '86 Tommasini Professional, '04 Teschner Aero FX Pro, '05 Alan Carbon Cross, '86 De Rosa Professional, '82 Colnago Super, '95 Gios Compact Pro, '95 Carrera Zeus, '84 Basso Gap, ‘89 Cinelli Supercorsa, ‘83 Bianchi Specialissima, ‘VO Randonneur, Ritchey Breakaway Steel, '84 Paletti Super Prestige, Heron Randonneur
N = '96 Colnago C40, '04 Wilier Alpe D'Huez, '10 Colnago EPS, '85 Merckx Pro, '89 Merckx Century, '86 Tommasini Professional, '04 Teschner Aero FX Pro, '05 Alan Carbon Cross, '86 De Rosa Professional, '82 Colnago Super, '95 Gios Compact Pro, '95 Carrera Zeus, '84 Basso Gap, ‘89 Cinelli Supercorsa, ‘83 Bianchi Specialissima, ‘VO Randonneur, Ritchey Breakaway Steel, '84 Paletti Super Prestige, Heron Randonneur
#4
Senior Member
Try to tap them out backwards in the holders on the bike. If they don't move then...
Most common old school method was:
Remove shoes from bike,
Squeeze the rubber part only in a vise
Tap off the holders with a big dull punch and a hammer, or something like that.
Reverse procedure to tap in the new rubber, or just squeeze them in.
Reinstall pads and holders and readjust as necessary.
Most common old school method was:
Remove shoes from bike,
Squeeze the rubber part only in a vise
Tap off the holders with a big dull punch and a hammer, or something like that.
Reverse procedure to tap in the new rubber, or just squeeze them in.
Reinstall pads and holders and readjust as necessary.
#5
Senior Member
Use a hack saw to cut a groove along the centerline of the old pad.
Squeeze with a pliers and remove pads.
Remove the rust you are likely to find which is causing the pads to be so hard to remove.
Squeeze with a pliers and remove pads.
Remove the rust you are likely to find which is causing the pads to be so hard to remove.
#6
Senior Member
Join Date: Jun 2006
Posts: 20,305
Mentioned: 130 Post(s)
Tagged: 0 Thread(s)
Quoted: 3464 Post(s)
Liked 2,829 Times
in
1,995 Posts
A year ago I started finding OLD pads pretty challenging to remove- I assumed beyond the flex date.
the hack saw slit or dremel slit might just do the trick.
I have a section of angle iron with two 6mm plus holes- remove holders from brake affix to angle and tap them out with a drift.
copper jaws in vise and wind the fresh in.
at some point Campagnolo went with a floating pad holder bolt- that required an upset to clear the fastener head. Water soluble Goose grease helps press them in- rinse off.
the hack saw slit or dremel slit might just do the trick.
I have a section of angle iron with two 6mm plus holes- remove holders from brake affix to angle and tap them out with a drift.
copper jaws in vise and wind the fresh in.
at some point Campagnolo went with a floating pad holder bolt- that required an upset to clear the fastener head. Water soluble Goose grease helps press them in- rinse off.
Likes For repechage:
#7
Junior Member
Join Date: Mar 2007
Location: San Luis Obispo, CA
Posts: 175
Bikes: 1988 Bottecchia Professional (for Eroica), 2011 Ridley Noah ISP (retired), 2020 Soma Fog Cutter (daily commuter), 2021 Ridley Kanzo Adventure (gravel), 2022 Tideace Aero (main road bike).
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 77 Post(s)
Liked 76 Times
in
32 Posts
Take a pair of pliers and rip the old ones out. If they're old, they might tear and you just keep working until all the pieces are out. I've run Campy my whole life and I've never had old brake pads push out easily.
For the new ones, apply a liberal amount of dish soap and slide in. The torque/friction of the braking surface of the wheel on the new pads will fully seat them if needed.
For the new ones, apply a liberal amount of dish soap and slide in. The torque/friction of the braking surface of the wheel on the new pads will fully seat them if needed.
#8
Junior Member
Join Date: Aug 2016
Location: SF East Bay
Posts: 101
Bikes: Masi, Olmo, Miele, Masi, Masi
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 40 Post(s)
Likes: 0
Liked 34 Times
in
23 Posts
#9
Edumacator
Thread Starter
Join Date: Jan 2018
Location: Goose Creek, SC
Posts: 6,807
Bikes: '87 Crestdale, '87 Basso Gap, '92 Rossin Performance EL-OS, 1990 VanTuyl, 1980s Losa, 1985 Trek 670, 1982 AD SLE, 1987 PX10, etc...
Mentioned: 59 Post(s)
Tagged: 0 Thread(s)
Quoted: 2439 Post(s)
Liked 3,128 Times
in
1,967 Posts
Awesome suggestions all! I appreciate it. I got one out the wrong way by mistake, but it didn't deform the shoe. The pad seems to not wish to seat without popping up a little and so I backed it out and posted this.
Bench vise for installing with a bit of Dawn. Great ideas.
Removal...working on that one!
Bench vise for installing with a bit of Dawn. Great ideas.
Removal...working on that one!
__________________
1987 Crest Cannondale, 1987 Basso Gap, 1992 Rossin Performance EL, 1990ish Van Tuyl, 1985 Trek 670, 1982 AD SLE, 2003 Pinarello Surprise, 1990ish MBK Atlantique, 1987 Peugeot Competition, 1987 Nishiki Tri-A, 1981 Faggin, 1996 Cannondale M500, 1984 Mercian, 1982 AD SuperLeicht, 1985 Massi (model unknown), 1988 Daccordi Griffe , 1989 Fauxsin MTB, 1981 Ciocc Mockba, 1992 Bianchi Giro, 1977 Colnago Super
1987 Crest Cannondale, 1987 Basso Gap, 1992 Rossin Performance EL, 1990ish Van Tuyl, 1985 Trek 670, 1982 AD SLE, 2003 Pinarello Surprise, 1990ish MBK Atlantique, 1987 Peugeot Competition, 1987 Nishiki Tri-A, 1981 Faggin, 1996 Cannondale M500, 1984 Mercian, 1982 AD SuperLeicht, 1985 Massi (model unknown), 1988 Daccordi Griffe , 1989 Fauxsin MTB, 1981 Ciocc Mockba, 1992 Bianchi Giro, 1977 Colnago Super
#10
Bianchi Goddess
Join Date: Apr 2009
Location: Shady Pines Retirement Fort Wayne, In
Posts: 27,858
Bikes: Too many to list here check my signature.
Mentioned: 192 Post(s)
Tagged: 2 Thread(s)
Quoted: 2930 Post(s)
Liked 2,926 Times
in
1,491 Posts
If you haven’t pinched a finger or drawn blood with a screwdriver you’re doing it wrong
__________________
“One morning you wake up, the girl is gone, the bikes are gone, all that's left behind is a pair of old tires and a tube of tubular glue, all squeezed out"
Sugar "Kane" Kowalczyk
“One morning you wake up, the girl is gone, the bikes are gone, all that's left behind is a pair of old tires and a tube of tubular glue, all squeezed out"
Sugar "Kane" Kowalczyk
Likes For Bianchigirll:
#11
Super Moderator
Join Date: Jul 2004
Location: Ffld Cnty Connecticut
Posts: 21,843
Bikes: Old Steelies I made, Old Cannondales
Mentioned: 12 Post(s)
Tagged: 0 Thread(s)
Quoted: 1173 Post(s)
Liked 927 Times
in
612 Posts
I usually use wide jaw pliers with one jaw on the lip of the holder at the open end and the other jaw on the other end of the pad. Squeeze and viola! To install, lots of times I’ll put a drop of lube and then either do the reverse with the pliers or press the pad in with a bench vise.
__________________
Bikes: Old steel race bikes, old Cannondale race bikes, less old Cannondale race bike, crappy old mtn bike.
FYI: https://www.bikeforums.net/forum-sugg...ad-please.html
Bikes: Old steel race bikes, old Cannondale race bikes, less old Cannondale race bike, crappy old mtn bike.
FYI: https://www.bikeforums.net/forum-sugg...ad-please.html