QR to Thru Axel
#1
Senior Member
Thread Starter
QR to Thru Axel
Is it possible to convert a Shimano HB-RS505 from QR to Thru Axle? Thinking about getting a new frame and most disk brake frames seem to have gone to thru axle. Was hoping to keep my existing wheelset.
#2
Banned
NO.. You would be better off having TA Hubs to put in a TA frame .. #1 .. 10 is bigger than 9, 12 >than> 10..
TA hubs are Cartridge bearings QR loose ball cup & cone
https://bike.shimano.com/en-US/produ.../HB-RS505.html
QR hubs in a regular dropout.. keep the bike you used the wheels in .. (or have the wheel rims rebuilt around new TA Hubs)
https://bikerumor.com/2018/03/16/aas...hru-axle-fork/
....
TA hubs are Cartridge bearings QR loose ball cup & cone
https://bike.shimano.com/en-US/produ.../HB-RS505.html
QR hubs in a regular dropout.. keep the bike you used the wheels in .. (or have the wheel rims rebuilt around new TA Hubs)
https://bikerumor.com/2018/03/16/aas...hru-axle-fork/
....
Last edited by fietsbob; 07-17-20 at 12:16 PM.
#3
Occam's Rotor
Join Date: Jul 2013
Posts: 7,248
Mentioned: 61 Post(s)
Tagged: 0 Thread(s)
Quoted: 2366 Post(s)
Liked 2,331 Times
in
1,164 Posts
Some hubs are completely convertible; just the end-caps differ. I think the OP question is whether Shimano HB-RS505 is such a hub. (There is no indication that this is possible on Shimano's website).
#4
Banned
... as I found, looking it up, IMHO , it is not.
axle has to go through* and screw into one end of the frame
Hence Through Axle nomenclature..
///
axle has to go through* and screw into one end of the frame
Hence Through Axle nomenclature..
///
Last edited by fietsbob; 07-17-20 at 12:27 PM.
#6
Senior Member
Since the thru axle screws into the frame, has anyone ever had an issue with the frame becoming stripped over time? Aluminum threads tend to be quite soft.
#7
Senior Member
My experience as a mechanic is that this isn't a common problem. The axle is pretty large and the threads pretty course, and it's not under a ton of torque. They can get messed up if cross threaded, although again that's not very common.
Likes For cpach:
#8
Senior member
Join Date: Oct 2004
Location: Oakville Ontario
Posts: 8,115
Mentioned: 25 Post(s)
Tagged: 0 Thread(s)
Quoted: 942 Post(s)
Liked 656 Times
in
370 Posts
Focus came up with a non threaded design that uses a quarter turn lock tab that fits in a replaceable slot. The shop I was working for was a Focus dealer, and I never saw any problems with those either.
https://www.focus-bikes.com/fr_en/rat
#9
Banned
TA interface is quite large thread... TA axle is aluminum too.. a bit of grease on the thread might be good ..
#10
Senior Member
Here is an example of thru axle loosening: https://www.bikeforums.net/bicycle-m...loosening.html
So while the interface might seem fine and well, over time it could deteriorate to cause loosening when riding?
Which is better for preserving over time the thru axle to frame connection, grease or anti-seize?
I like the Focus innovation.
I'm also using a Wera Hex Plus like this one: https://www.primetools.co.uk/product...rewdriver-5mm/
This has no lever to apply leverage, so I just screw until tight, and I think that's perfect. I'm not noticing any loosening. People could get into trouble if using levered tools.
So while the interface might seem fine and well, over time it could deteriorate to cause loosening when riding?
Which is better for preserving over time the thru axle to frame connection, grease or anti-seize?
I like the Focus innovation.
I'm also using a Wera Hex Plus like this one: https://www.primetools.co.uk/product...rewdriver-5mm/
This has no lever to apply leverage, so I just screw until tight, and I think that's perfect. I'm not noticing any loosening. People could get into trouble if using levered tools.
#11
Senior Member
Just a dab of anti-seize works well for me, and that's probably why I get sufficient torque using the unlevered tool as tight as I can go. Probably hard to go wrong in any case, but I like taking care of my things as well as I can. The bolt unscrews easily yet doesn't loosen after long, aggressive riding.
#12
Senior Member
I never had problems with threaded thru axles as a shop mechanic.
Focus came up with a non threaded design that uses a quarter turn lock tab that fits in a replaceable slot. The shop I was working for was a Focus dealer, and I never saw any problems with those either.
https://www.focus-bikes.com/fr_en/rat
Focus came up with a non threaded design that uses a quarter turn lock tab that fits in a replaceable slot. The shop I was working for was a Focus dealer, and I never saw any problems with those either.
https://www.focus-bikes.com/fr_en/rat