What is this British Steel?
#1
Junior Member
Thread Starter
Join Date: Jul 2012
Posts: 14
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
What is this British Steel?
I'm having a hard time deciding exactly what this is - a Raleigh / Carlton of some kind I think - the BB frame # of "DD 136" suggests its a 1969 going by Kurt's published codes - but that's the only code on the BB - or the frame for that matter.
It has Campy dropouts but no chroming - and no decals for id, apart from the Reynolds ones - which do incidentally look original, but I'd be more definite about the originality of the paintwork (lagoon blue possibly?). Lugwork detail is nice but not overfancy as on some of the later professionals I've seen....
Any ideas? Your advice and input will be greatly appreciated - TIA!
It has Campy dropouts but no chroming - and no decals for id, apart from the Reynolds ones - which do incidentally look original, but I'd be more definite about the originality of the paintwork (lagoon blue possibly?). Lugwork detail is nice but not overfancy as on some of the later professionals I've seen....
Any ideas? Your advice and input will be greatly appreciated - TIA!
#3
Stop reading my posts!
Join Date: Sep 2004
Posts: 12,584
Mentioned: 90 Post(s)
Tagged: 0 Thread(s)
Quoted: 1443 Post(s)
Liked 1,062 Times
in
787 Posts
that "leaf" cap on the seat stays was something favored by Bernard Carre (France) but also by Jan LeGrand who was chief mechanic for Raleigh TI and probably had some influence on the SBDU frames. Besides that little bit, I have no idea about this particular frame...looks good, though. I'm sure it wouldn't have those details (under-BB cabling, braze-ons, short dropouts) if it was built in '69.
If it was a LeGrand "Presto" (his own brand) it would have other give-away details like a diamond-section brake bridge and "XXX" marking on the BB shell, etc.
If it was a LeGrand "Presto" (his own brand) it would have other give-away details like a diamond-section brake bridge and "XXX" marking on the BB shell, etc.
Last edited by unworthy1; 08-27-12 at 09:15 AM.
#4
incazzare.
What's the seatpost size? BB threading?
__________________
1964 JRJ (Bob Jackson), 1973 Wes Mason, 1974 Raleigh Gran Sport, 1986 Schwinn High Sierra, 2000ish Colian (Colin Laing), 2011 Dick Chafe, 2013 Velo Orange Pass Hunter
1964 JRJ (Bob Jackson), 1973 Wes Mason, 1974 Raleigh Gran Sport, 1986 Schwinn High Sierra, 2000ish Colian (Colin Laing), 2011 Dick Chafe, 2013 Velo Orange Pass Hunter
#5
Junior Member
Thread Starter
Join Date: Jul 2012
Posts: 14
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
#6
Senior Member
Join Date: Oct 2009
Location: Minneapolis
Posts: 2,470
Bikes: -1973 Motobecane Mirage -197? Velosolex L'Etoile -'71 Raleigh Super Course
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 2 Times
in
2 Posts
That actually looks a lot like my 3Rensho built Specialized Allez Comp. Seatstay cluster and fork look that way, anyhow. Decals can come from anywhere, of course. Mine doesn't have the cable guides under the BB or the stamped shell, but dang, it's close.
#8
Senior Member
Join Date: Dec 2005
Posts: 17,158
Mentioned: 481 Post(s)
Tagged: 0 Thread(s)
Quoted: 3810 Post(s)
Liked 6,699 Times
in
2,611 Posts
I'm not seeing anything that shouts Raleigh or Carlton.
#9
Junior Member
Thread Starter
Join Date: Jul 2012
Posts: 14
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
That's right - I don't think there is any evidence of headbadge fitting or filling of headbadge holes. Intriguing since I really don't think it's been repainted - looking at the numerous scratches there is only one layer of paint. Then again I haven't inspected the head tube really closely - will do so tomorrow and report back if findings are any different....
#10
Junior Member
Thread Starter
Join Date: Jul 2012
Posts: 14
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Let me give a quick update on what I'm thinking. Definitely not 'Raleigh' - there is nothing in Raleigh catalogues that is remotely similar. However, I did find this site giving details of a Carlton Professional:
https://www.mytenspeeds.com/My_TenSpe..._2_Finding.htm
On that page about half way down is a pic of seat lug detail that seems similar to my example. Many of the other details of the bikes are different, but that's not necessarily surprising if the dating estimate of 1969 based on the stamped frame code is correct (and the date code format does seem to correspond to that used by Raleigh/Carlton). It also seems that Carlton did produce their own cycles alongside Raleigh production and also had their own catalogue - a 1970 Carlton catalogue is on Bulgier, but again this is for a year later than my case so I wouldn't expect it to correspond exactly.
However, all this is fairly loose and could quite easily be completely wrong...just my current best guess really..... until someone comes up with a better one!
https://www.mytenspeeds.com/My_TenSpe..._2_Finding.htm
On that page about half way down is a pic of seat lug detail that seems similar to my example. Many of the other details of the bikes are different, but that's not necessarily surprising if the dating estimate of 1969 based on the stamped frame code is correct (and the date code format does seem to correspond to that used by Raleigh/Carlton). It also seems that Carlton did produce their own cycles alongside Raleigh production and also had their own catalogue - a 1970 Carlton catalogue is on Bulgier, but again this is for a year later than my case so I wouldn't expect it to correspond exactly.
However, all this is fairly loose and could quite easily be completely wrong...just my current best guess really..... until someone comes up with a better one!
#11
Stop reading my posts!
Join Date: Sep 2004
Posts: 12,584
Mentioned: 90 Post(s)
Tagged: 0 Thread(s)
Quoted: 1443 Post(s)
Liked 1,062 Times
in
787 Posts
If I were the owner, I might bother Don Gillies to take a look at this frame...if it's anything from Raleigh or Carlton (or not), he might know.
gillies(AT)cs.ubc.ca
Since I don't know how he'd feel about a "blind email request" for his participation, I should approach him very politely.
gillies(AT)cs.ubc.ca
Since I don't know how he'd feel about a "blind email request" for his participation, I should approach him very politely.
#13
Crawlin' up, flyin' down
Join Date: Jan 2006
Location: Democratic Peoples' Republic of Berkeley
Posts: 5,656
Bikes: 1967 Paramount; 1982-ish Ron Cooper; 1978 Eisentraut "A"; two mid-1960s Cinelli Speciale Corsas; and others in various stages of non-rideability.
Mentioned: 40 Post(s)
Tagged: 0 Thread(s)
Quoted: 1026 Post(s)
Liked 2,528 Times
in
1,058 Posts
I agree that both the under-BB cable routing and the style of Reynolds sticker say "probably 1980s, definitely not 1969." BTW, a 1969 Reynolds 531 frame sticker would have the "531" on a slant (at least for the butted tubes), and the fork stickers would be triangular in shape, with a flat top side.
__________________
"I'm in shape -- round is a shape." Andy Rooney
"I'm in shape -- round is a shape." Andy Rooney
#14
Senior Member
Join Date: Nov 2005
Posts: 5,768
Bikes: Cinelli, Paramount, Raleigh, Carlton, Zeus, Gemniani, Frejus, Legnano, Pinarello, Falcon
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 12 Post(s)
Likes: 0
Liked 8 Times
in
8 Posts
Doesn't say Carlton to me. I believe that Reynolds decal was for an anniversary, 1984.
#15
Junior Member
Thread Starter
Join Date: Jul 2012
Posts: 14
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Thanks to those who have contributed so far and have nudged things (and me) in the right direction (perhaps) of the 1980s. I've collated more evidence, which doesn’t necessarily lend itself to a consistent conclusion
1) All the components are shimano – Tange headset, shimano light action shifters/mechs, biopace chainwheels, 105 cranks, Rigida rims with Maillard hubs, Weinmann 570 sidepulls, Shimnao SLR brake levers. Sounds like mid-80’s. So is this really an 80’s bike (eg a Raleigh Ritmo?) that somebody has painted in Carlton colours? Paint does not look like a factory finish, the Reynolds decals do look wrong (too new) for even an 80’s bike, and I can’t see where any headbadge placement was – so the frame must have been filled, painted, and newer Reynolds decals applied. However, if this is true somebody went to a vast amount of trouble with all the lug highlighting – which was then detracted from with the Shimano component build. Seems a little self contradictory to expend the effort, but then everybody’s different (and perhaps the original owner really wanted a Carlton but couldn't afford/obtain one).
2) However, the frame numbering is still anomalous. Later Raleighs (I thought) all had the 'Raleigh system' of numbering which is not like the AAnnn stamped on the bottom bracket of this bike. So is this really an older frame (seat clamp bolt is threaded into the frame itself unlike all 80’s Raleighs that I’ve seen) that has been updated with Shimano components – but then that also would seem a little pointless.
So the search goes on, and I’ll research more into 1980’s Raleighs to see if I can find any similarities....
1) All the components are shimano – Tange headset, shimano light action shifters/mechs, biopace chainwheels, 105 cranks, Rigida rims with Maillard hubs, Weinmann 570 sidepulls, Shimnao SLR brake levers. Sounds like mid-80’s. So is this really an 80’s bike (eg a Raleigh Ritmo?) that somebody has painted in Carlton colours? Paint does not look like a factory finish, the Reynolds decals do look wrong (too new) for even an 80’s bike, and I can’t see where any headbadge placement was – so the frame must have been filled, painted, and newer Reynolds decals applied. However, if this is true somebody went to a vast amount of trouble with all the lug highlighting – which was then detracted from with the Shimano component build. Seems a little self contradictory to expend the effort, but then everybody’s different (and perhaps the original owner really wanted a Carlton but couldn't afford/obtain one).
2) However, the frame numbering is still anomalous. Later Raleighs (I thought) all had the 'Raleigh system' of numbering which is not like the AAnnn stamped on the bottom bracket of this bike. So is this really an older frame (seat clamp bolt is threaded into the frame itself unlike all 80’s Raleighs that I’ve seen) that has been updated with Shimano components – but then that also would seem a little pointless.
So the search goes on, and I’ll research more into 1980’s Raleighs to see if I can find any similarities....
#16
Senior Member
Join Date: Aug 2014
Location: Los Angeles, CA
Posts: 522
Bikes: None in ridable condition
Mentioned: 125 Post(s)
Tagged: 0 Thread(s)
Quoted: 148 Post(s)
Liked 644 Times
in
192 Posts
I know this thread is an oldie but there's no statute of limitations on cold cases, is there? No thread left behind!
Don't know if @jo1010 still comes by, or even owns this bike anymore, so I'm updating this for reference.
The frame here was made by Rick Powell of Dinnington (South Yorkshire). Rick worked at Carlton for decades, becoming chief frame paint sprayer and eventually shop foreman. After the Carlton shop closed in 1981, he started building under his own name. The company was called "DD Enterprises" which explains the "DD" in the serial number. I vaguely remember reading somewhere that DD Enterprises was an existing (possibly family) business that frame building was merged with.
Also, I've only ever seen "DD" decals on the head tube of all Rick's frames, which would explain the lack of head badge rivet holes.
With the serial of DD136, it would be one of the earlier examples, so probably early to mid 80s (as @big chainring pointed out). The green example below has a number in the 800s. Rick built until 2003, but I've not come across any records of numbers from that period.
Examples:
Don't know if @jo1010 still comes by, or even owns this bike anymore, so I'm updating this for reference.
The frame here was made by Rick Powell of Dinnington (South Yorkshire). Rick worked at Carlton for decades, becoming chief frame paint sprayer and eventually shop foreman. After the Carlton shop closed in 1981, he started building under his own name. The company was called "DD Enterprises" which explains the "DD" in the serial number. I vaguely remember reading somewhere that DD Enterprises was an existing (possibly family) business that frame building was merged with.
Also, I've only ever seen "DD" decals on the head tube of all Rick's frames, which would explain the lack of head badge rivet holes.
With the serial of DD136, it would be one of the earlier examples, so probably early to mid 80s (as @big chainring pointed out). The green example below has a number in the 800s. Rick built until 2003, but I've not come across any records of numbers from that period.
Examples:
Likes For MauriceMoss:
#17
vintage motor
Join Date: Sep 2008
Location: Tepic, Nayarit, Mexico
Posts: 1,595
Bikes: 48 Automoto, 49 Stallard, 50 Rotrax, 62 Jack Taylor, 67 Atala, 68 Lejeune, 72-74-75 Motobecanes, 73 RIH, 71 Zieleman, 74 Raleigh, 78 Windsor, 83 Messina (Villata), 84 Brazzo (Losa), 85 Davidson, 90 Diamondback, 92 Kestrel
Mentioned: 6 Post(s)
Tagged: 0 Thread(s)
Quoted: 164 Post(s)
Likes: 0
Liked 102 Times
in
79 Posts
The nearly-straight fork rake seems very English, although from one of the smaller builders.
#18
Stop reading my posts!
Join Date: Sep 2004
Posts: 12,584
Mentioned: 90 Post(s)
Tagged: 0 Thread(s)
Quoted: 1443 Post(s)
Liked 1,062 Times
in
787 Posts
Double D DAY-um! There's no statute of limitations when you are going to nail it, and no statue of imitations when you're the one and only Maurice Moss, bravo again!
Likes For unworthy1:
#20
Senior Member
Join Date: Jan 2004
Location: Madison, WI USA
Posts: 6,154
Mentioned: 50 Post(s)
Tagged: 0 Thread(s)
Quoted: 2363 Post(s)
Liked 1,749 Times
in
1,191 Posts
Likes For madpogue:
#21
Extraordinary Magnitude
Join Date: Aug 2009
Location: Waukesha WI
Posts: 13,647
Bikes: 1978 Trek TX700; 1978/79 Trek 736; 1984 Specialized Stumpjumper Sport; 1984 Schwinn Voyageur SP; 1985 Trek 620; 1985 Trek 720; 1986 Trek 400 Elance; 1987 Schwinn High Sierra; 1990 Miyata 1000LT
Mentioned: 84 Post(s)
Tagged: 0 Thread(s)
Quoted: 2608 Post(s)
Liked 1,702 Times
in
937 Posts
Having the information is one thing, but finding an 8 year old thread with next to no tangible information in it and being able to match it up... that's sleuthing!
__________________
*Recipient of the 2006 Time Magazine "Person Of The Year" Award*
Commence to jigglin’ huh?!?!
"But hey, always love to hear from opinionated amateurs." -says some guy to Mr. Marshall.
Commence to jigglin’ huh?!?!
"But hey, always love to hear from opinionated amateurs." -says some guy to Mr. Marshall.
Likes For The Golden Boy:
#22
Disraeli Gears
I was going to say, about the OP bike, that the build/neatness quality seems to far exceed almost any Raleigh product (and I've had at least 4, so not just going on BikeForums prejudice and/or pictures). Those are nice bikes!
#23
Senior Member
Join Date: Aug 2014
Location: Los Angeles, CA
Posts: 522
Bikes: None in ridable condition
Mentioned: 125 Post(s)
Tagged: 0 Thread(s)
Quoted: 148 Post(s)
Liked 644 Times
in
192 Posts
Thanks @The Golden Boy!
I think the secret is that I just have trouble staying focused.
Most of the time I'll be doing an image search for one specific thing, then in the process see an unrelated pic ("ooh, this looks cool..."), follow that link to another link ("wait, this looks vaguely familiar - where did I see that before?") and, a hop, skip and a jump later, I end up updating an 8 year old thread.
I actually don't even remember what I was originally searching for when I stumbled upon this thread .
Likes For MauriceMoss:
#25
Senior Member
Join Date: Apr 2007
Location: Thunder Bay, Ontario, Canada - burrrrr!
Posts: 11,674
Bikes: 1958 Rabeneick 120D, 1968 Legnano Gran Premio, 196? Torpado Professional, 2000 Marinoni Piuma
Mentioned: 210 Post(s)
Tagged: 0 Thread(s)
Quoted: 1372 Post(s)
Likes: 0
Liked 1,751 Times
in
938 Posts
Until recently I did not even know that a Raleigh Carlton existed. And now, I have one...
__________________
"98% of the bikes I buy are projects".
"98% of the bikes I buy are projects".