Notices
Classic and Vintage Sales Private Sales Only, no online storefronts. All prices must be quoted, we are not an auction site.

ISO: "touring" parts..

Old 01-23-21, 10:25 PM
  #1  
shoota 
Senior Member
Thread Starter
 
shoota's Avatar
 
Join Date: Jun 2012
Location: Stillwater, OK
Posts: 8,128
Mentioned: 33 Post(s)
Tagged: 0 Thread(s)
Quoted: 1871 Post(s)
Liked 689 Times in 467 Posts
ISO: "touring" parts..

..even though I won't be touring. But I need to set up my bike with low enough gearing to race 150 miles and 10,000ft climbing.
I'm thinking 32h 700c wheels, 170mm low-geared (triple?) crankset w/ corresponding Italian BB, derailleurs, 13-32? freewheel or similar (7s?) cassette (obviously has to match the wheels), barend shifters, indexed would be awesome.
Also need toe strap type pedals. And a Selle San Marco Regal from the 80s. And possibly a full size frame pump. Piece of cake right?

- crank ✓
- barend indexed (8s?) group
- 32h wheels
- BB (for Sakae triple crank)
- freewheel/cassette (depends on the wheels) ✓
- toe strap pedals ✓
- 26.6 seatpost ~300mm+ ✓
- Vittoria 1976 shoes (size 11)
- Selle San Marco Regal ✓
- frame pump

Last edited by shoota; 02-01-21 at 06:59 PM.
shoota is offline  
Old 01-24-21, 05:04 AM
  #2  
bikemig 
Senior Member
 
bikemig's Avatar
 
Join Date: Apr 2012
Location: Middle Earth (aka IA)
Posts: 20,505

Bikes: A bunch of old bikes and a few new ones

Mentioned: 178 Post(s)
Tagged: 0 Thread(s)
Quoted: 5877 Post(s)
Liked 3,445 Times in 2,066 Posts
Tough to beat a 110 bcd crank which you can run as a triple. With 7 on the back and the ride you're talking about (150 miles, 10000 ft climbing), I'd run a triple. I like the old school MTB set up with 46/36/24 rings and an 11-28 7 speed cassette. 11-28 7 speed cassettes are available new even if the supply has been drying up with the pandemic. If you go with a freewheel, 14-28 is the most likely combo new but there are older freewheels out there with 13-28 or even 12-28 but they may be hard to source. Bottom line is first you have to figure out what kind of wheels you are running (freewheel or cassette) as that will likely make a difference as to what kind of rings you want for the crank.

For new 126 OLD wheels, I'd check out what velomine has for sale as well. They have reasonable prices and good products.

For a crank, a 110 bcd crank is your best bet but you'll find more supply at 175 mm than 170 since 175 was a pretty common size on MTBs. The supply of square taper bottom brackets is shrinking but you can still find 68 x 127 BBs. Those seem to work the best with the shimano deore triples I've set up.

For shifters, 7 speed shimano bar ends are a great choice. For derailleurs, just run shimano deore derailleurs.

Last edited by bikemig; 01-24-21 at 05:13 AM.
bikemig is offline  
Old 01-24-21, 05:08 AM
  #3  
morri869 
Full Member
 
morri869's Avatar
 
Join Date: Oct 2011
Location: Milwaukee, WI
Posts: 403

Bikes: 1984 Lotus Classique, 1996 Cannondale T700

Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 91 Post(s)
Liked 139 Times in 67 Posts
Depends what you are looking for, but I have a sakae triple and an ultegra 6503 (octalink) triple & long cage rd
morri869 is offline  
Old 01-24-21, 05:54 AM
  #4  
shoota 
Senior Member
Thread Starter
 
shoota's Avatar
 
Join Date: Jun 2012
Location: Stillwater, OK
Posts: 8,128
Mentioned: 33 Post(s)
Tagged: 0 Thread(s)
Quoted: 1871 Post(s)
Liked 689 Times in 467 Posts
Originally Posted by bikemig
Tough to beat a 110 bcd crank which you can run as a triple. With 7 on the back and the ride you're talking about (150 miles, 10000 ft climbing), I'd run a triple. I like the old school MTB set up with 46/36/24 rings and an 11-28 7 speed cassette. 11-28 7 speed cassettes are available new even if the supply has been drying up with the pandemic. If you go with a freewheel, 14-28 is the most likely combo new but there are older freewheels out there with 13-28 or even 12-28 but they may be hard to source. Bottom line is first you have to figure out what kind of wheels you are running (freewheel or cassette) as that will likely make a difference as to what kind of rings you want for the crank.

For new 126 OLD wheels, I'd check out what velomine has for sale as well. They have reasonable prices and good products.

For a crank, a 110 bcd crank is your best bet but you'll find more supply at 175 mm than 170 since 175 was a pretty common size on MTBs. The supply of square taper bottom brackets is shrinking but you can still find 68 x 127 BBs. Those seem to work the best with the shimano deore triples I've set up.

For shifters, 7 speed shimano bar ends are a great choice. For derailleurs, just run shimano deore derailleurs.
Can I get the setup you’re describing in indexed form? That actually works well (not like Campy’s garbage indexing groups of the 80s).
__________________
2014 Cannondale SuperSix EVO 2
2019 Salsa Warbird
shoota is offline  
Old 01-24-21, 05:55 AM
  #5  
shoota 
Senior Member
Thread Starter
 
shoota's Avatar
 
Join Date: Jun 2012
Location: Stillwater, OK
Posts: 8,128
Mentioned: 33 Post(s)
Tagged: 0 Thread(s)
Quoted: 1871 Post(s)
Liked 689 Times in 467 Posts
Originally Posted by morri869
Depends what you are looking for, but I have a sakae triple and an ultegra 6503 (octalink) triple & long cage rd
Maybe, what are the specifics on the Sakae cranks?
shoota is offline  
Old 01-24-21, 06:30 AM
  #6  
bikemig 
Senior Member
 
bikemig's Avatar
 
Join Date: Apr 2012
Location: Middle Earth (aka IA)
Posts: 20,505

Bikes: A bunch of old bikes and a few new ones

Mentioned: 178 Post(s)
Tagged: 0 Thread(s)
Quoted: 5877 Post(s)
Liked 3,445 Times in 2,066 Posts
Originally Posted by shoota
Can I get the setup you’re describing in indexed form? That actually works well (not like Campy’s garbage indexing groups of the 80s).
Yes. Shimano 7 speed indexing works very well. I set up my 1985 Cannondale ST 400 pretty much as you described for long distance riding in hilly terrain. I think the frame is very well designed for long distance riding (long chainstays but with a stiff responsive frame). It's a reasonably light weight bike and has 3 water bottle braze ons. I set it up with 700 x 32c tires and 3 x 7 shimano shifting. The only thing I'd change is eventually I'll install shimano 7 speed bar ends. There's nothing wrong with downtube shifters but bar ends are a plus I think for a long ride.


Last edited by bikemig; 01-24-21 at 06:45 AM.
bikemig is offline  
Old 01-24-21, 06:59 AM
  #7  
bikemig 
Senior Member
 
bikemig's Avatar
 
Join Date: Apr 2012
Location: Middle Earth (aka IA)
Posts: 20,505

Bikes: A bunch of old bikes and a few new ones

Mentioned: 178 Post(s)
Tagged: 0 Thread(s)
Quoted: 5877 Post(s)
Liked 3,445 Times in 2,066 Posts
It sounds like you're starting with a frame since you are looking for an Italian BB. Are you looking to just change out the drive train and you have the rest of the parts in hand?

Last edited by bikemig; 01-24-21 at 07:03 AM.
bikemig is offline  
Old 01-24-21, 07:06 AM
  #8  
mountaindave 
tantum vehi
 
mountaindave's Avatar
 
Join Date: Jul 2008
Location: Flathead Valley, MT
Posts: 4,548

Bikes: More than I care to admit

Mentioned: 153 Post(s)
Tagged: 0 Thread(s)
Quoted: 1166 Post(s)
Liked 962 Times in 480 Posts
Originally Posted by bikemig
Yes. Shimano 7 speed indexing works very well... The only thing I'd change is eventually I'll install shimano 7 speed bar ends. There's nothing wrong with downtube shifters but bar ends are a plus I think for a long ride.
Especially if your frame is 60cm or larger...



Now if you want to get eccentric (not in the bottom bracket) one could also explore the half step plus granny route with just a six speed cassette: 50-45-24 up front and 12-14-17-21-26-32 in back. You’ll have to make the cassette yourself out of two other cassettes, but it’s doable. Put a shiny chrome dork disk on and you’ve got your spacer on a 7s hub. Ask me how I know...

Last edited by mountaindave; 01-24-21 at 07:13 AM.
mountaindave is online now  
Likes For mountaindave:
Old 01-24-21, 07:13 AM
  #9  
bikemig 
Senior Member
 
bikemig's Avatar
 
Join Date: Apr 2012
Location: Middle Earth (aka IA)
Posts: 20,505

Bikes: A bunch of old bikes and a few new ones

Mentioned: 178 Post(s)
Tagged: 0 Thread(s)
Quoted: 5877 Post(s)
Liked 3,445 Times in 2,066 Posts
If the frame you are working from is a racing bike with tight clearances, you might want to consider a compact crank. Triples can be a bit of a PITA to set up with short chain stays.
bikemig is offline  
Old 01-24-21, 07:47 AM
  #10  
rccardr 
aka: Dr. Cannondale
 
rccardr's Avatar
 
Join Date: Jul 2009
Posts: 7,852
Mentioned: 234 Post(s)
Tagged: 0 Thread(s)
Quoted: 2151 Post(s)
Liked 3,380 Times in 1,198 Posts
Sounds like you're looking at that vintage gravel bike race later this year...
__________________
Hard at work in the Secret Underground Laboratory...
rccardr is online now  
Likes For rccardr:
Old 01-24-21, 11:25 AM
  #11  
morri869 
Full Member
 
morri869's Avatar
 
Join Date: Oct 2011
Location: Milwaukee, WI
Posts: 403

Bikes: 1984 Lotus Classique, 1996 Cannondale T700

Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 91 Post(s)
Liked 139 Times in 67 Posts
Originally Posted by shoota
Maybe, what are the specifics on the Sakae cranks?
Sakae sx cranks, 170mm length, 50/39/28 chainrings.

morri869 is offline  
Old 01-24-21, 04:27 PM
  #12  
shoota 
Senior Member
Thread Starter
 
shoota's Avatar
 
Join Date: Jun 2012
Location: Stillwater, OK
Posts: 8,128
Mentioned: 33 Post(s)
Tagged: 0 Thread(s)
Quoted: 1871 Post(s)
Liked 689 Times in 467 Posts
Originally Posted by morri869
Sakae sx cranks, 170mm length, 50/39/28 chainrings.

I'll PM you!
__________________
2014 Cannondale SuperSix EVO 2
2019 Salsa Warbird
shoota is offline  
Old 01-24-21, 04:41 PM
  #13  
shoota 
Senior Member
Thread Starter
 
shoota's Avatar
 
Join Date: Jun 2012
Location: Stillwater, OK
Posts: 8,128
Mentioned: 33 Post(s)
Tagged: 0 Thread(s)
Quoted: 1871 Post(s)
Liked 689 Times in 467 Posts
Originally Posted by bikemig
It sounds like you're starting with a frame since you are looking for an Italian BB. Are you looking to just change out the drive train and you have the rest of the parts in hand?
Yeah more or less. I mean the rest of the parts are the easy part of this. Getting the right groupset with so many moving parts is the hard part. I'll post the frame I'm working with to the original post here shortly.

Originally Posted by bikemig
If the frame you are working from is a racing bike with tight clearances, you might want to consider a compact crank. Triples can be a bit of a PITA to set up with short chain stays.
Yeah mid 70s Windsor. Techncially a race bike but I'm not sure I'd call it "tight". I mean heck I can fit a 36mm tire in the front and a 40mm in the back. The other option is a 1986 Schwinn Voyageur. I'd be starting from the same spot with that one too. Its English BB is a plus, but its canti brakes, vertical dropouts, and geo aren't.

Originally Posted by rccardr
Sounds like you're looking at that vintage gravel bike race later this year...
Gravel Worlds here I come!
__________________
2014 Cannondale SuperSix EVO 2
2019 Salsa Warbird
shoota is offline  
Old 01-24-21, 04:47 PM
  #14  
bikemig 
Senior Member
 
bikemig's Avatar
 
Join Date: Apr 2012
Location: Middle Earth (aka IA)
Posts: 20,505

Bikes: A bunch of old bikes and a few new ones

Mentioned: 178 Post(s)
Tagged: 0 Thread(s)
Quoted: 5877 Post(s)
Liked 3,445 Times in 2,066 Posts
You might want to consider a 650b conversion for that Windsor but brake reach may be an issue. The parts mix is easy. I’d just get Deore/shimano 600 quality parts and go 3 by 7 with shimano bar end shifters. One thing I've found is that when setting up a triple with a shimano 110/74 bcd crank, a 127 mm sealed square taper bottom bracket works best.

Last edited by bikemig; 01-24-21 at 04:53 PM.
bikemig is offline  
Old 01-24-21, 07:59 PM
  #15  
shoota 
Senior Member
Thread Starter
 
shoota's Avatar
 
Join Date: Jun 2012
Location: Stillwater, OK
Posts: 8,128
Mentioned: 33 Post(s)
Tagged: 0 Thread(s)
Quoted: 1871 Post(s)
Liked 689 Times in 467 Posts
Originally Posted by bikemig
You might want to consider a 650b conversion for that Windsor but brake reach may be an issue. The parts mix is easy. I’d just get Deore/shimano 600 quality parts and go 3 by 7 with shimano bar end shifters. One thing I've found is that when setting up a triple with a shimano 110/74 bcd crank, a 127 mm sealed square taper bottom bracket works best.
Well, so, I've found out that 7s barend shifters aren't exactly easy to find or cheap. After tinkering with things tonight I'm half decided to go with the Schwinn Voyageur. I'm not sure the 3x7 indexed XT/Deore option you're talking about will be easy to find. And honestly, for the sake of ease a 2x7 drivetrain would be awesome, if I could find a period correct ~50/34 crank. 48/32 would be ideal. Did someone like TA make such a thing?
__________________
2014 Cannondale SuperSix EVO 2
2019 Salsa Warbird
shoota is offline  
Old 01-24-21, 09:06 PM
  #16  
shoota 
Senior Member
Thread Starter
 
shoota's Avatar
 
Join Date: Jun 2012
Location: Stillwater, OK
Posts: 8,128
Mentioned: 33 Post(s)
Tagged: 0 Thread(s)
Quoted: 1871 Post(s)
Liked 689 Times in 467 Posts
morri869 just hooked me up with that triple crank, so that will be a great starting point. I should edit the original post with a better checklist of things I need. 7s indexed barends would be amazing!
__________________
2014 Cannondale SuperSix EVO 2
2019 Salsa Warbird
shoota is offline  
Old 01-25-21, 04:35 AM
  #17  
bikemig 
Senior Member
 
bikemig's Avatar
 
Join Date: Apr 2012
Location: Middle Earth (aka IA)
Posts: 20,505

Bikes: A bunch of old bikes and a few new ones

Mentioned: 178 Post(s)
Tagged: 0 Thread(s)
Quoted: 5877 Post(s)
Liked 3,445 Times in 2,066 Posts
Originally Posted by shoota
Well, so, I've found out that 7s barend shifters aren't exactly easy to find or cheap. After tinkering with things tonight I'm half decided to go with the Schwinn Voyageur. I'm not sure the 3x7 indexed XT/Deore option you're talking about will be easy to find. And honestly, for the sake of ease a 2x7 drivetrain would be awesome, if I could find a period correct ~50/34 crank. 48/32 would be ideal. Did someone like TA make such a thing?
You should put up a separate WTB for the 7 speed bar ends. You'll find them. Also you might want to put up a separate WTB for a shimano indexing long cage rear derailleur. The Deore XTs are pretty bombproof and index great.

The triple you just bought is a 110/74. You can go 50/34 with the outer two. You could try running it using the middle and inner only in which case you can run as low as 24 on the inside. I've never set it up that way though.

If you want a vintage double that can go as low as 32 on the inside, you can look for a 50.4 bcd crank (TA is the most famous) (new chainrings are available on eBay) or an 86 bcd crank (Stronglight 99 is the most common but SR and other companies made a copy) (new chainrings are available from UK vendors like Spa cycles). Nervar 631 is a TA copy and you can pick one up for less than a TA. One good thing about Nervar is that you don't need a special chain puller. With an 86 bcd crank, you can go as low as 28 on the inside and with the TA (or TA copy) you can go as low as 26 if memory serves me right.

Last edited by bikemig; 01-25-21 at 05:03 AM.
bikemig is offline  
Old 01-25-21, 07:25 AM
  #18  
clubman 
Phyllo-buster
 
clubman's Avatar
 
Join Date: Jan 2010
Location: Nova Scotia
Posts: 8,829

Bikes: roadsters, club bikes, fixed and classic

Mentioned: 133 Post(s)
Tagged: 0 Thread(s)
Quoted: 2287 Post(s)
Liked 2,028 Times in 1,244 Posts
I'd have no hesitation subbing in DX, LX, for the XT gear. Heck I've got a 200GS that I've ignored (beat up a bit?) on my winter bike for 4 years and it never misses a shift with thumbies. That early 90's generation of Deore/Exage 7 speeds RD's are super functional. Some are just heavier.
clubman is offline  
Likes For clubman:
Old 01-25-21, 10:17 AM
  #19  
shoota 
Senior Member
Thread Starter
 
shoota's Avatar
 
Join Date: Jun 2012
Location: Stillwater, OK
Posts: 8,128
Mentioned: 33 Post(s)
Tagged: 0 Thread(s)
Quoted: 1871 Post(s)
Liked 689 Times in 467 Posts
Originally Posted by bikemig
You should put up a separate WTB for the 7 speed bar ends. You'll find them. Also you might want to put up a separate WTB for a shimano indexing long cage rear derailleur. The Deore XTs are pretty bombproof and index great.

The triple you just bought is a 110/74. You can go 50/34 with the outer two. You could try running it using the middle and inner only in which case you can run as low as 24 on the inside. I've never set it up that way though.

If you want a vintage double that can go as low as 32 on the inside, you can look for a 50.4 bcd crank (TA is the most famous) (new chainrings are available on eBay) or an 86 bcd crank (Stronglight 99 is the most common but SR and other companies made a copy) (new chainrings are available from UK vendors like Spa cycles). Nervar 631 is a TA copy and you can pick one up for less than a TA. One good thing about Nervar is that you don't need a special chain puller. With an 86 bcd crank, you can go as low as 28 on the inside and with the TA (or TA copy) you can go as low as 26 if memory serves me right.
These are all great points. I just heard back from the race organizers and they are going to get feedback from all the vintage riders once registration closes. Then we'll have a consensus on what is acceptable for the drivetrain. I suppose I'll just focus on the other parts that I need for now and get the shifty bits later. They alluded that 8s indexed might be acceptable, and if so that would definitely be the way to go.
__________________
2014 Cannondale SuperSix EVO 2
2019 Salsa Warbird
shoota is offline  
Old 01-25-21, 12:15 PM
  #20  
sallen73
Junior Member
 
Join Date: Oct 2017
Location: Chicago, IL
Posts: 79

Bikes: 1988 Ross Centaur, 2010 Fuji Connoisseur, 2015 Raleigh Tamland 1, 2017 Raleigh Carlton, 1987 Team Miyata, 2012 Soma Stanyan, 2015 Cinelli Supercorsa, 1984 Miyata 1000, [2009 Scattante SSR], [1988 Falcon Competitor 105], [2016 Soma Wolverine]

Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 26 Post(s)
Likes: 0
Liked 12 Times in 10 Posts
Glad to know that I'm not the only one tackling that race in the vintage class!
Brand new carbon gravel bike - nah, I think the 35 year old Miyata with 35 year old brakes and shifters will do just nicely, thank you!
sallen73 is offline  
Likes For sallen73:
Old 01-25-21, 12:20 PM
  #21  
shoota 
Senior Member
Thread Starter
 
shoota's Avatar
 
Join Date: Jun 2012
Location: Stillwater, OK
Posts: 8,128
Mentioned: 33 Post(s)
Tagged: 0 Thread(s)
Quoted: 1871 Post(s)
Liked 689 Times in 467 Posts
Originally Posted by sallen73
Glad to know that I'm not the only one tackling that race in the vintage class!
Brand new carbon gravel bike - nah, I think the 35 year old Miyata with 35 year old brakes and shifters will do just nicely, thank you!
Ha! Same. I convinced the wife to let me borrow her '86 Schwinn Voyageur. That might be the bike I wind up riding.
__________________
2014 Cannondale SuperSix EVO 2
2019 Salsa Warbird
shoota is offline  
Old 01-25-21, 12:42 PM
  #22  
bikemig 
Senior Member
 
bikemig's Avatar
 
Join Date: Apr 2012
Location: Middle Earth (aka IA)
Posts: 20,505

Bikes: A bunch of old bikes and a few new ones

Mentioned: 178 Post(s)
Tagged: 0 Thread(s)
Quoted: 5877 Post(s)
Liked 3,445 Times in 2,066 Posts
Hah, this is out of Lincoln NE. This looks cool. A vintage class in the midwest is interesting. This would be a fun test for a 650b conversion. The bike only has to be pre 1988 . . . .

Last edited by bikemig; 01-25-21 at 12:53 PM.
bikemig is offline  
Likes For bikemig:
Old 01-25-21, 03:43 PM
  #23  
merziac
Senior Member
 
merziac's Avatar
 
Join Date: Oct 2015
Location: PDX
Posts: 14,099

Bikes: Merz x 5 + Specialized Merz Allez x 2, Strawberry/Newlands/DiNucci/Ti x3, Gordon, Fuso/Moulton x2, Bornstein, Paisley,1958-74 Paramounts x3, 3rensho, 74 Moto TC, 73-78 Raleigh Pro's x5, Marinoni x2, 1960 Cinelli SC, 1980 Bianchi SC, PX-10 X 2

Mentioned: 267 Post(s)
Tagged: 0 Thread(s)
Quoted: 4493 Post(s)
Liked 6,297 Times in 3,632 Posts
Originally Posted by shoota
..even though I won't be touring. But I need to set up my bike with low enough gearing to race 150 miles and 10,000ft climbing.
I'm thinking 32h 700c wheels, 170mm low-geared (triple?) crankset w/ corresponding Italian BB, derailleurs, 13-32? freewheel or similar (7s?) cassette (obviously has to match the wheels), barend shifters, indexed would be awesome.
Also need toe strap type pedals. And a Selle San Marco Regal from the 80s. And possibly a full size frame pump. Piece of cake right?

- crank ✓
- barend indexed (7s?) group
- 32h wheels
- BB (for Sakae triple crank)
- freewheel/cassette (depends on the wheels)
- toe strap pedals
- 26.6 seatpost ~300mm+
- Vittoria 1976 shoes (size 11)
- Selle San Marco Regal
- frame pump
MKS Sylvan, touring or?

Tough as nails, vintage as the day is long and one of the best values in cycling.
merziac is offline  
Old 01-25-21, 05:19 PM
  #24  
shoota 
Senior Member
Thread Starter
 
shoota's Avatar
 
Join Date: Jun 2012
Location: Stillwater, OK
Posts: 8,128
Mentioned: 33 Post(s)
Tagged: 0 Thread(s)
Quoted: 1871 Post(s)
Liked 689 Times in 467 Posts
Originally Posted by merziac
MKS Sylvan, touring or?

Tough as nails, vintage as the day is long and one of the best values in cycling.
Yeah you got a pair?
__________________
2014 Cannondale SuperSix EVO 2
2019 Salsa Warbird
shoota is offline  
Old 01-25-21, 05:41 PM
  #25  
merziac
Senior Member
 
merziac's Avatar
 
Join Date: Oct 2015
Location: PDX
Posts: 14,099

Bikes: Merz x 5 + Specialized Merz Allez x 2, Strawberry/Newlands/DiNucci/Ti x3, Gordon, Fuso/Moulton x2, Bornstein, Paisley,1958-74 Paramounts x3, 3rensho, 74 Moto TC, 73-78 Raleigh Pro's x5, Marinoni x2, 1960 Cinelli SC, 1980 Bianchi SC, PX-10 X 2

Mentioned: 267 Post(s)
Tagged: 0 Thread(s)
Quoted: 4493 Post(s)
Liked 6,297 Times in 3,632 Posts
Originally Posted by shoota
Yeah you got a pair?
I don't have any to spare

You can buy brand new ones on efbay, Universal cycles and many others, they have not really changed in decades.
merziac is offline  
Likes For merziac:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.