so why no disk brakes on touring bikes?
#1
genec
Thread Starter
Join Date: Sep 2004
Location: West Coast
Posts: 27,079
Bikes: custom built, sannino, beachbike, giant trance x2
Mentioned: 86 Post(s)
Tagged: 0 Thread(s)
Quoted: 13658 Post(s)
Liked 4,532 Times
in
3,158 Posts
so why no disk brakes on touring bikes?
Just wondering. I have cantis on my very old touring bike... and I have looked at a couple new bikes like the Bruce Gordons and Trek and LHT, but I don't see disk brakes...
Is it simply weight, or is there some other negative reason for the lack of disk brakes on touring bikes.
Is it simply weight, or is there some other negative reason for the lack of disk brakes on touring bikes.
#2
It's true, man.
Join Date: Aug 2005
Location: North Texas
Posts: 2,726
Bikes: Cannondale T1000, Inbred SS 29er, Supercaliber 29er, Crescent Mark XX, Burley Rumba Tandem
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 2 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
I can't wait to show you my disk-braked tourer, as soon as it's finished in a week or two.
#3
Bike touring webrarian
Does this look familiar?
#4
genec
Thread Starter
Join Date: Sep 2004
Location: West Coast
Posts: 27,079
Bikes: custom built, sannino, beachbike, giant trance x2
Mentioned: 86 Post(s)
Tagged: 0 Thread(s)
Quoted: 13658 Post(s)
Liked 4,532 Times
in
3,158 Posts
At least it isn't one of these...
#5
Fat Guy on a Little Bike
Join Date: Jun 2008
Location: Philadelphia, PA
Posts: 15,944
Bikes: Two wheeled ones
Mentioned: 42 Post(s)
Tagged: 0 Thread(s)
Quoted: 1254 Post(s)
Liked 345 Times
in
174 Posts
I hope I'm not stepping into anything here...
I test rode a Kona Sutra with STIs and Disc brakes. The braking was horrendous and the levers felt spongey. The bike was discounted to $700 because no one liked how it felt and the shop said they'd never stock them again. I have no idea if they just didn't set them up properly or if there was inherent weakness, but that bike simply didn't stop properly.
On the other side, a friend from the forum built an awesome Soma with disc brakes and STIs and that stopped like a dream.
I test rode a Kona Sutra with STIs and Disc brakes. The braking was horrendous and the levers felt spongey. The bike was discounted to $700 because no one liked how it felt and the shop said they'd never stock them again. I have no idea if they just didn't set them up properly or if there was inherent weakness, but that bike simply didn't stop properly.
On the other side, a friend from the forum built an awesome Soma with disc brakes and STIs and that stopped like a dream.
#6
genec
Thread Starter
Join Date: Sep 2004
Location: West Coast
Posts: 27,079
Bikes: custom built, sannino, beachbike, giant trance x2
Mentioned: 86 Post(s)
Tagged: 0 Thread(s)
Quoted: 13658 Post(s)
Liked 4,532 Times
in
3,158 Posts
I hope I'm not stepping into anything here...
I test rode a Kona Sutra with STIs and Disc brakes. The braking was horrendous and the levers felt spongey. The bike was discounted to $700 because no one liked how it felt and the shop said they'd never stock them again. I have no idea if they just didn't set them up properly or if there was inherent weakness, but that bike simply didn't stop properly.
On the other side, a friend from the forum built an awesome Soma with disc brakes and STIs and that stopped like a dream.
I test rode a Kona Sutra with STIs and Disc brakes. The braking was horrendous and the levers felt spongey. The bike was discounted to $700 because no one liked how it felt and the shop said they'd never stock them again. I have no idea if they just didn't set them up properly or if there was inherent weakness, but that bike simply didn't stop properly.
On the other side, a friend from the forum built an awesome Soma with disc brakes and STIs and that stopped like a dream.
But here is a whole new technology... so why is it not found on touring bikes, typically.
Of course one can build up a darn nice touring bike with any features you want. But that's a different story.
#7
Senior Member
Join Date: Jul 2009
Location: DFW
Posts: 48
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
#8
Senior Member
I would say it's partly tradition (i.e. cantilevers are viewed as simpler, easier to maintain, more "classic", etc.). More importantly, the calipers can also make mounting racks and fenders awkward, though I believe some frames now (e.g. Gunnar) are positioning the rear IS mount in such a way that it doesn't interfere as much.
There are plenty of options for disc-compatible frames and brake levers/calipers these days though, especially if you don't mind running a disc in front and a canti/V-brake in back (then you can use any frame you want and just change out the fork). I don't know if anyone makes a true touring-specific disc fork (i.e. one with dual dropout eyelets and mid-fork rack eyelets, which might make the fork too weak for a disc), but there are plenty of cyclocross disc forks. I've been looking at the Salsa La Cruz fork for my new build. I like the forward-facing SS dropouts.
There are plenty of options for disc-compatible frames and brake levers/calipers these days though, especially if you don't mind running a disc in front and a canti/V-brake in back (then you can use any frame you want and just change out the fork). I don't know if anyone makes a true touring-specific disc fork (i.e. one with dual dropout eyelets and mid-fork rack eyelets, which might make the fork too weak for a disc), but there are plenty of cyclocross disc forks. I've been looking at the Salsa La Cruz fork for my new build. I like the forward-facing SS dropouts.
#9
ah.... sure.
Join Date: Mar 2008
Location: Whidbey Island WA
Posts: 4,107
Bikes: Specialized.... schwinn..... enough to fill my needs..
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
If I was going to use disc brakes I would only bother with the front. Nothing gained on the rear. I almost never use my rear brake as it is... Now on a mountain bike it's a whole different story.
Canti's stop me fast enough and are cheap and easy to maintain. Good enough for me.
Canti's stop me fast enough and are cheap and easy to maintain. Good enough for me.
#10
Senior Member
Join Date: Sep 2008
Posts: 5,200
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 137 Post(s)
Likes: 0
Liked 81 Times
in
64 Posts
It's pretty simple, the touring market is miniscule compared to mtn. bikes, kid bikes and hybrids so there isn't much incentive to introducing a whole new line of wheels and forks and frames when all a manufacturer has to do is grab what's off the shelf and allocate high quality parts for where it matters. Custom and low production manufacturers offer discs. I suspect it'll become more common in the future but for the person who just wants to go on a trip the decision of rim or disc has no bearing on the trip happening whereas a companies ability to sell a bike for a profit hinges on offering the best value for the money.
#13
Senior Member
Join Date: Jul 2007
Posts: 2,114
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
As for not being on a touring bike, there are some reasons. One would be the weaker wheels. Another reason has been mentioned above about rack and fender issues. As with anything, there are pros and cons for all options. I have not toured with disc brakes, but I don't think it would bother me at all. I actually like the idea for long mountain descents. I'm always nervous about overheating the rims and having a tire blow off when continuously braking.
#14
Fat Guy on a Little Bike
Join Date: Jun 2008
Location: Philadelphia, PA
Posts: 15,944
Bikes: Two wheeled ones
Mentioned: 42 Post(s)
Tagged: 0 Thread(s)
Quoted: 1254 Post(s)
Liked 345 Times
in
174 Posts
I couldn't tell you what was on it. It had a fairly nice group from what I recall...105 stuff mostly.
#15
Senior Member
I checked the specs and they're Avid BB7 Roads, which are what I use. I found them a bit tricky to dial in at first, especially since it was my first experience with discs. And, of course, no disc brake will stop very well until the pads are broken in, which can take a while.
#16
Senior Member
Just wondering. I have cantis on my very old touring bike... and I have looked at a couple new bikes like the Bruce Gordons and Trek and LHT, but I don't see disk brakes...
Is it simply weight, or is there some other negative reason for the lack of disk brakes on touring bikes.
Is it simply weight, or is there some other negative reason for the lack of disk brakes on touring bikes.
Salsa Vaya, Co-Motion will put them on any of their tourers, Raleigh Sojourn, Jamis Aurora Elite (just added disc brakes this year), Kona Sutra, REI Novara Fargo, etc. etc.
#17
Fat Guy on a Little Bike
Join Date: Jun 2008
Location: Philadelphia, PA
Posts: 15,944
Bikes: Two wheeled ones
Mentioned: 42 Post(s)
Tagged: 0 Thread(s)
Quoted: 1254 Post(s)
Liked 345 Times
in
174 Posts
I checked the specs and they're Avid BB7 Roads, which are what I use. I found them a bit tricky to dial in at first, especially since it was my first experience with discs. And, of course, no disc brake will stop very well until the pads are broken in, which can take a while.
I have serious brand aversion towards Avid. I had their shorty 4s on my JTS cross bike and found them to be terrible...especially the stock pads. An old set of dia-compes far outperformed them.
#18
genec
Thread Starter
Join Date: Sep 2004
Location: West Coast
Posts: 27,079
Bikes: custom built, sannino, beachbike, giant trance x2
Mentioned: 86 Post(s)
Tagged: 0 Thread(s)
Quoted: 13658 Post(s)
Liked 4,532 Times
in
3,158 Posts
I don't know what brakes are on the Sutra, but cheap disc brakes are not any better than cheap linear pull brakes, when it comes to stopping power. A good disc brake is better, especially in wet conditions.
As for not being on a touring bike, there are some reasons. One would be the weaker wheels. Another reason has been mentioned above about rack and fender issues. As with anything, there are pros and cons for all options. I have not toured with disc brakes, but I don't think it would bother me at all. I actually like the idea for long mountain descents. I'm always nervous about overheating the rims and having a tire blow off when continuously braking.
As for not being on a touring bike, there are some reasons. One would be the weaker wheels. Another reason has been mentioned above about rack and fender issues. As with anything, there are pros and cons for all options. I have not toured with disc brakes, but I don't think it would bother me at all. I actually like the idea for long mountain descents. I'm always nervous about overheating the rims and having a tire blow off when continuously braking.
With regard to the whole tour bike industry... yeah, I can see the issues... my bike was in fact custom built at the time, so I wasn't really depending on the industry per se to deliver what I needed.
I am however looking to get a new bike, and thought I would start with what is available now... I was rather disappointed to NOT see disc brakes as an option... considering my past experience with the mountains (bad) and my recent experience with my MTB (good). My bike back then (which I still have) was something of a hybrid between a road bike and a fat tire MTB, using MTB components for the drive train, but having a fairly upright and long road frame, but with fat tires. (a real mixed beast)
I don't think the Trek 520 has changed in years... except for the components... the LHT doesn't seem to have options for discs either.
Oh well, apparently going custom is the only route... so be it.
#19
genec
Thread Starter
Join Date: Sep 2004
Location: West Coast
Posts: 27,079
Bikes: custom built, sannino, beachbike, giant trance x2
Mentioned: 86 Post(s)
Tagged: 0 Thread(s)
Quoted: 13658 Post(s)
Liked 4,532 Times
in
3,158 Posts
Thanks... interesting that the Jamis just added them. REI is close to me... so worth a look. I looked at the Konas a few years ago, they had discs but no braze-ons for racks... back then.
#20
Grateful Tread
Join Date: Dec 2009
Location: Exeter, Ontario Canada
Posts: 119
Bikes: Rocky Mountain Cardiac (hardtail MB/commuter), Aquila Pave (aluminum tourer)
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
I don't know much about disc brakes, as I've never had the opportunity to ride anything with them. My understanding is that they're much more effective than rim brakes, but potentially require more maintenance. Not sure if this is true or not - just what I've heard.
Is it possible that they'd be avoided on an 'expedition ready' tourer for maintenance reasons? Mind you, from what I've heard disc brakes work on bent rims, so that might be an advantage in the middle of nowhere...
Is it possible that they'd be avoided on an 'expedition ready' tourer for maintenance reasons? Mind you, from what I've heard disc brakes work on bent rims, so that might be an advantage in the middle of nowhere...
#21
Member
Join Date: Jul 2008
Location: British Columbia, Canada
Posts: 26
Bikes: 2007 Norco CCX xxl
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
When I bought my Norco CCX a few years ago it came with bb7's and cheap SORA brifters, the braking is awesome. Strong and predictable in the dry or the wet. One of the best things is the ease of adjustment. Just passing 1000km on a new set of pads this week, getting a little too much travel on the levers now, so I just turned the adjustment dials in on the calipers a couple clicks. Fast and easy. Spare pads are tiny and light and easy to change.
I ride with Axion Lasalle bags on the rear rack all the time, no interference with the rear caliper. Don't have a front rack so can't comment there. Anyway, I am a larger man, 6'4" and 230 pounds, and when I am coming down a long hill with lots of groceries or gear in the bags and then have to stop suddenly, I can easily modulate the braking to keep it right where I like it - just a fraction below wheel lock-up. The front rotor gets so hot it smokes and hisses in the rain, which I think is cool. No loss of performance on long downhills when its just me and the panniers. When I am towing the trailer and it is quite heavy, I do get some brake fade on longer hills, but that just means squeezing harder than normal and using the rear brake more than normal. I will always prefer a bike with discs now. I love them. Hold out for a touring bike with discs!
-Ryan
p.s. (due to cyclocross regs, Norco has gone back to cross bikes with no disc brakes again I think.)
I ride with Axion Lasalle bags on the rear rack all the time, no interference with the rear caliper. Don't have a front rack so can't comment there. Anyway, I am a larger man, 6'4" and 230 pounds, and when I am coming down a long hill with lots of groceries or gear in the bags and then have to stop suddenly, I can easily modulate the braking to keep it right where I like it - just a fraction below wheel lock-up. The front rotor gets so hot it smokes and hisses in the rain, which I think is cool. No loss of performance on long downhills when its just me and the panniers. When I am towing the trailer and it is quite heavy, I do get some brake fade on longer hills, but that just means squeezing harder than normal and using the rear brake more than normal. I will always prefer a bike with discs now. I love them. Hold out for a touring bike with discs!
-Ryan
p.s. (due to cyclocross regs, Norco has gone back to cross bikes with no disc brakes again I think.)
#22
Banned
Join Date: Aug 2005
Posts: 5,115
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 2 Times
in
1 Post
I think one reason is that one doesn't stop so much on touring bikes. A lot of the time one is noodling along and hours go by with no really dramatic brake use. Compared to urban cycling or MTBs. Obviously your downhills may vary, and I have been on tours where a fair amount of my time was spent dreaming up more effective brake systems.
That said, most manufacturers have price points in mind, and they may only allow one or two big buys, like a Brooks seat. So which do you want, the Brooks and the bar ends, or the BB7s? BB7s are actually a premium buy, in line with what I spent on my Paul Cantis, though more likely to be found on sale at Nashbar. Don't find many Pauls on medium priced touring bikes either.
That said, most manufacturers have price points in mind, and they may only allow one or two big buys, like a Brooks seat. So which do you want, the Brooks and the bar ends, or the BB7s? BB7s are actually a premium buy, in line with what I spent on my Paul Cantis, though more likely to be found on sale at Nashbar. Don't find many Pauls on medium priced touring bikes either.
#23
Senior Member
Join Date: Jan 2007
Posts: 101
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
I have a Marinoni Turismo Extreme with Avid bb7's and Ultegra brifters. It has far superior braking to my Jamis Nova, or my Specialized Tarmac. Have a Blackburn rack on the back, Axiom rack on the front, everything fit fine. Fully loaded, have had no problems on some of the 20+ km decents around here. I would heartily recommend discs to anyone.
Cheers
Cheers
#24
Senior Member
If I was ever building a touring bike from scratch, no question I'd put disk(s) on it.
#25
cyclopath
Join Date: Apr 2006
Location: Victoria, BC
Posts: 5,264
Bikes: Surly Krampus, Surly Straggler, Pivot Mach 6, Bike Friday Tikit, Bike Friday Tandem, Santa Cruz Nomad
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 6 Times
in
6 Posts
I have touring bikes with both discs and v-brakes...in my opinion...there is no slam dunk either way. Each system has pros and cons depending on the specifics of a situation both can come out on top.
You can definitely tour just about anywhere with either system if you really want to.
I will say that I have never felt that I was at any disadvantage on a tour with my v-brakes vs. discs.
You can definitely tour just about anywhere with either system if you really want to.
I will say that I have never felt that I was at any disadvantage on a tour with my v-brakes vs. discs.