Fitting grips
#1
Senior Member
Thread Starter
Fitting grips
On my electric scooter the current grips are 120mm. The best I could find were 130mm. So there may be a slight overhang . Any tips ?
picture shows the original stock ones
picture shows the original stock ones
#2
Senior Member
Join Date: Jun 2015
Location: Low Country, SC, USA
Posts: 99
Bikes: Trek Madone 2.5, single speed
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 30 Post(s)
Likes: 0
Liked 29 Times
in
13 Posts
Loosen screws on shifter, bell, etc., and move until grip slides on bar 100%. Then retighten everything.
Likes For zeeway:
#3
Senior Member
Thread Starter
I can do the brake lever and potentially the bell but I don’t think you can move the shifter on the right ...
these are the ones I bought...
https://www.pureelectric.com/collect...andlebar-grips
if they’re no good I’ll try these
www.amazon.co.uk/dp/B071GKG78P/ref=cm_sw_r_cp_api_i_MHhzFb2GFB113
i could always stuff some tissue into the end which doesn’t go on ?
#4
Senior Member
Join Date: Feb 2012
Location: Rochester, NY
Posts: 18,063
Bikes: Stewart S&S coupled sport tourer, Stewart Sunday light, Stewart Commuting, Stewart Touring, Co Motion Tandem, Stewart 3-Spd, Stewart Track, Fuji Finest, Mongoose Tomac ATB, GT Bravado ATB, JCP Folder, Stewart 650B ATB
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4197 Post(s)
Liked 3,849 Times
in
2,300 Posts
I seriously doubt the shifter is a fixed to bars assembly. Perhaps a set screw in a less then obvious location? Another grip sizing option is if the grips are slide ons (not clamped ons) is to simple shorten the open end with a sharp knife. Andy
__________________
AndrewRStewart
AndrewRStewart
#5
Senior Member
Thread Starter
yes after some YouTubing I found a way to adjust the throttle so I can bring it inward
#6
Senior Member
Thread Starter
Hey
when putting the new grips on should I use some alcohol wipes to lubricate it as it will dry. Rather than using WD40 ?
when putting the new grips on should I use some alcohol wipes to lubricate it as it will dry. Rather than using WD40 ?
Likes For venomx:
#7
Droid on a mission
Join Date: May 2018
Location: Palm Coast, FL
Posts: 1,005
Bikes: Diamondback Wildwood Classic
Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 317 Post(s)
Liked 280 Times
in
195 Posts
I prefer alcohol or even have used hair spray to lube the installation of grips
__________________
JoeTBM (The Bike Man) - I'm a black & white type of guy, the only gray in my life is the hair on my head
www.TheBikeMenOfFlaglerCounty.com
JoeTBM (The Bike Man) - I'm a black & white type of guy, the only gray in my life is the hair on my head
www.TheBikeMenOfFlaglerCounty.com
#8
Junior Member
+1 on hair spray. Also, OP could install longer grips and cut then to size, either in or outside of grips, but in case of outside, it would need some plugs to close the handlebar ends and avoid a serious wound in case of an accident.
Likes For dwsmartins:
#9
Senior Member
Join Date: Feb 2015
Location: Mission Viejo
Posts: 5,805
Bikes: 1986 Cannondale SR400 (Flat bar commuter), 1988 Cannondale Criterium XTR, 1992 Serotta T-Max, 1995 Trek 970
Mentioned: 20 Post(s)
Tagged: 0 Thread(s)
Quoted: 1943 Post(s)
Liked 2,164 Times
in
1,323 Posts
I have 600mm bars on my mountain bikes. I cut about a half inch off each of my ESI grips to give me just a skosh more width. I use a hose clamp as a guide for cutting the grip accurate and straight.
...and I use hair spray to install.
John
...and I use hair spray to install.
John