Drilling out a riveted crankset to replace the rings?
#1
Senior Member
Thread Starter
Join Date: Sep 2017
Location: Eastern Shore, MD
Posts: 2,107
Bikes: Road ready: 1993 Koga Miyata City Liner Touring Hybrid, 1989 Centurion Sport DLX, "I Blame GP" Bridgestone CB-1. Projects: Yea, I got a problem....
Mentioned: 24 Post(s)
Tagged: 0 Thread(s)
Quoted: 753 Post(s)
Liked 737 Times
in
422 Posts
Drilling out a riveted crankset to replace the rings?
Occupational hazard right now is surfing ebay on my phone. I bought this crankset assuming it had bolted on 94 BCD rings. I just opened the package and realized it is actually riveted together.
What are the chances I can drill the rivets and use chainring bolts to hold on the replacement chainrings? I'm not realy concerned with the inner chain ring.
What are the chances I can drill the rivets and use chainring bolts to hold on the replacement chainrings? I'm not realy concerned with the inner chain ring.
#3
Senior Member
Join Date: Apr 2007
Location: Thunder Bay, Ontario, Canada - burrrrr!
Posts: 11,674
Bikes: 1958 Rabeneick 120D, 1968 Legnano Gran Premio, 196? Torpado Professional, 2000 Marinoni Piuma
Mentioned: 210 Post(s)
Tagged: 0 Thread(s)
Quoted: 1372 Post(s)
Likes: 0
Liked 1,751 Times
in
938 Posts
I would be concerned about finding ring bolts that would fit properly. That said, I really don't know but I do know that not all bolts fit all crank/ring assemblies.
__________________
"98% of the bikes I buy are projects".
"98% of the bikes I buy are projects".
#4
Senior Member
Join Date: Feb 2020
Posts: 2,820
Mentioned: 49 Post(s)
Tagged: 0 Thread(s)
Quoted: 1106 Post(s)
Likes: 0
Liked 1,328 Times
in
784 Posts
They chances are good - if
a) you can get bolts to fit; and
b) you know what you are doing.
To help with b) above -
Get a drill-press (or a friend with a drill-press) and use it. Clamp the part well, you don't want those teeth suddenly spinning where your forearm used to be. If the rivet spins before the drill-bit takes the head off, mount another bit underneath and place the back side of the rivet on the up-ended bit.
For a) you'll have to get at least one of them out so you can measure.
a) you can get bolts to fit; and
b) you know what you are doing.
To help with b) above -
Get a drill-press (or a friend with a drill-press) and use it. Clamp the part well, you don't want those teeth suddenly spinning where your forearm used to be. If the rivet spins before the drill-bit takes the head off, mount another bit underneath and place the back side of the rivet on the up-ended bit.
For a) you'll have to get at least one of them out so you can measure.
Likes For oneclick:
#5
feros ferio
Join Date: Jul 2000
Location: www.ci.encinitas.ca.us
Posts: 21,798
Bikes: 1959 Capo Modell Campagnolo; 1960 Capo Sieger (2); 1962 Carlton Franco Suisse; 1970 Peugeot UO-8; 1982 Bianchi Campione d'Italia; 1988 Schwinn Project KOM-10;
Mentioned: 44 Post(s)
Tagged: 0 Thread(s)
Quoted: 1393 Post(s)
Liked 1,325 Times
in
837 Posts
Editorial: I hate rivets and components designed not to be repairable.
__________________
"Far and away the best prize that life offers is the chance to work hard at work worth doing." --Theodore Roosevelt
Capo: 1959 Modell Campagnolo, S/N 40324; 1960 Sieger (2), S/N 42624, 42597
Carlton: 1962 Franco Suisse, S/N K7911
Peugeot: 1970 UO-8, S/N 0010468
Bianchi: 1982 Campione d'Italia, S/N 1.M9914
Schwinn: 1988 Project KOM-10, S/N F804069
"Far and away the best prize that life offers is the chance to work hard at work worth doing." --Theodore Roosevelt
Capo: 1959 Modell Campagnolo, S/N 40324; 1960 Sieger (2), S/N 42624, 42597
Carlton: 1962 Franco Suisse, S/N K7911
Peugeot: 1970 UO-8, S/N 0010468
Bianchi: 1982 Campione d'Italia, S/N 1.M9914
Schwinn: 1988 Project KOM-10, S/N F804069
Likes For John E:
#6
Senior Member
Join Date: Dec 2005
Posts: 17,158
Mentioned: 481 Post(s)
Tagged: 0 Thread(s)
Quoted: 3810 Post(s)
Liked 6,699 Times
in
2,611 Posts
Yeah, with a drill press it's likely an easy job, and I'd imagine those chainrings could be fitted with standard chainring bolts or, if you're going with new rings, the spider will take standard bolts.
Likes For nlerner:
#7
Senior Member
Thread Starter
Join Date: Sep 2017
Location: Eastern Shore, MD
Posts: 2,107
Bikes: Road ready: 1993 Koga Miyata City Liner Touring Hybrid, 1989 Centurion Sport DLX, "I Blame GP" Bridgestone CB-1. Projects: Yea, I got a problem....
Mentioned: 24 Post(s)
Tagged: 0 Thread(s)
Quoted: 753 Post(s)
Liked 737 Times
in
422 Posts
Looking at it I should be able just grind the heads off and skip the drilling. Its a $20 question as that's all I'd get back after shipping them back. I guess there's reasonable odds that Suntour used standard size bolt holes in the spider.
And on further inspection, its a no go. The big 94 bcd ring is riveted to the middle ring. rats
And on further inspection, its a no go. The big 94 bcd ring is riveted to the middle ring. rats
Last edited by bark_eater; 11-30-20 at 02:02 AM.
#8
Senior Member
It has been a personal dream of mine for over two decades to drill out the crappy rivets on stamped cranksets. (I used to have a beautiful Schwinn World with a stamped crankset that made me angry). GO FOR IT!!!!!!. DO IT for all of the rest of us that always wanted to try but never had the time or patience. Post the results here on the forums. I will cheer you on!!! You can get chain ring bolt sets on ebay for pretty cheap. But, that might not fit right. Could be that some plain old little bitty nuts & bolts from the hardware store might work. Please try & let me know how it works out.
Likes For ramzilla:
#9
Senior Member
Join Date: Feb 2020
Posts: 2,820
Mentioned: 49 Post(s)
Tagged: 0 Thread(s)
Quoted: 1106 Post(s)
Likes: 0
Liked 1,328 Times
in
784 Posts
Looking at it I should be able just grind the heads off and skip the drilling. Its a $20 question as that's all I'd get back after shipping them back. I guess there's reasonable odds that Suntour used standard size bolt holes in the spider.
And on further inspection, its a no go. The big 94 bcd ring is riveted to the middle ring. rats
And on further inspection, its a no go. The big 94 bcd ring is riveted to the middle ring. rats
Likes For oneclick:
#10
Mr. Anachronism
Join Date: Jan 2013
Location: Somewhere west of Tobie's
Posts: 2,087
Bikes: fillet-brazed Chicago Schwinns, and some other stuff
Mentioned: 29 Post(s)
Tagged: 0 Thread(s)
Quoted: 526 Post(s)
Liked 256 Times
in
165 Posts
It has been a personal dream of mine for over two decades to drill out the crappy rivets on stamped cranksets. (I used to have a beautiful Schwinn World with a stamped crankset that made me angry). GO FOR IT!!!!!!. DO IT for all of the rest of us that always wanted to try but never had the time or patience. Post the results here on the forums. I will cheer you on!!! You can get chain ring bolt sets on ebay for pretty cheap. But, that might not fit right. Could be that some plain old little bitty nuts & bolts from the hardware store might work. Please try & let me know how it works out.
__________________
"My only true wisdom is in knowing I have none" -Socrates
"My only true wisdom is in knowing I have none" -Socrates
#11
Old fart
Join Date: Nov 2004
Location: Appleton WI
Posts: 24,786
Bikes: Several, mostly not name brands.
Mentioned: 153 Post(s)
Tagged: 0 Thread(s)
Quoted: 3588 Post(s)
Liked 3,400 Times
in
1,934 Posts
I suspect it would be more trouble than it is worth. Considering the cost of individual rings and the potential for unforeseen difficulties, I think replacing the whole crank would be a better solution. If you have access to a bike co-op, you could probably pick up a used crank for not much money.
#12
feros ferio
Join Date: Jul 2000
Location: www.ci.encinitas.ca.us
Posts: 21,798
Bikes: 1959 Capo Modell Campagnolo; 1960 Capo Sieger (2); 1962 Carlton Franco Suisse; 1970 Peugeot UO-8; 1982 Bianchi Campione d'Italia; 1988 Schwinn Project KOM-10;
Mentioned: 44 Post(s)
Tagged: 0 Thread(s)
Quoted: 1393 Post(s)
Liked 1,325 Times
in
837 Posts
Drill, baby, drill!
__________________
"Far and away the best prize that life offers is the chance to work hard at work worth doing." --Theodore Roosevelt
Capo: 1959 Modell Campagnolo, S/N 40324; 1960 Sieger (2), S/N 42624, 42597
Carlton: 1962 Franco Suisse, S/N K7911
Peugeot: 1970 UO-8, S/N 0010468
Bianchi: 1982 Campione d'Italia, S/N 1.M9914
Schwinn: 1988 Project KOM-10, S/N F804069
"Far and away the best prize that life offers is the chance to work hard at work worth doing." --Theodore Roosevelt
Capo: 1959 Modell Campagnolo, S/N 40324; 1960 Sieger (2), S/N 42624, 42597
Carlton: 1962 Franco Suisse, S/N K7911
Peugeot: 1970 UO-8, S/N 0010468
Bianchi: 1982 Campione d'Italia, S/N 1.M9914
Schwinn: 1988 Project KOM-10, S/N F804069
#13
feros ferio
Join Date: Jul 2000
Location: www.ci.encinitas.ca.us
Posts: 21,798
Bikes: 1959 Capo Modell Campagnolo; 1960 Capo Sieger (2); 1962 Carlton Franco Suisse; 1970 Peugeot UO-8; 1982 Bianchi Campione d'Italia; 1988 Schwinn Project KOM-10;
Mentioned: 44 Post(s)
Tagged: 0 Thread(s)
Quoted: 1393 Post(s)
Liked 1,325 Times
in
837 Posts
I have de-riveted and de-screwed a number of cassette spiders to facilitate my penchant for gear phreaking.
__________________
"Far and away the best prize that life offers is the chance to work hard at work worth doing." --Theodore Roosevelt
Capo: 1959 Modell Campagnolo, S/N 40324; 1960 Sieger (2), S/N 42624, 42597
Carlton: 1962 Franco Suisse, S/N K7911
Peugeot: 1970 UO-8, S/N 0010468
Bianchi: 1982 Campione d'Italia, S/N 1.M9914
Schwinn: 1988 Project KOM-10, S/N F804069
"Far and away the best prize that life offers is the chance to work hard at work worth doing." --Theodore Roosevelt
Capo: 1959 Modell Campagnolo, S/N 40324; 1960 Sieger (2), S/N 42624, 42597
Carlton: 1962 Franco Suisse, S/N K7911
Peugeot: 1970 UO-8, S/N 0010468
Bianchi: 1982 Campione d'Italia, S/N 1.M9914
Schwinn: 1988 Project KOM-10, S/N F804069
#14
Senior Member
Join Date: Oct 2016
Location: Cambridge UK
Posts: 852
Bikes: 1903 24 spd Sunbeam, 1927 Humber, 3 1930 Raleighs, 2 1940s Sunbeams, 2 1940s Raleighs, Rudge, 1950s Robin Hood, 1958 Claud Butler, 2 1973 Colnago Supers, Eddie Merckx, 2 1980 Holdsworth, EG Bates funny TT bike, another 6 or so 1990s bikes
Mentioned: 15 Post(s)
Tagged: 0 Thread(s)
Quoted: 331 Post(s)
Liked 332 Times
in
185 Posts
Check the BCD (Bolt Circle Diameter) of the chain-ring you are hoping to use.The measurements are very precise and no amount of sweat can get the wrong BCD spider to fit an incompatible chain-ring. Better still go to co-op get a battered old crank of the correct BCD that is solid and put your desired chain-ring on it.
#15
Newbie
Join Date: Jan 2020
Location: eastern CT
Posts: 46
Bikes: yes
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 14 Post(s)
Likes: 0
Liked 10 Times
in
10 Posts
I've removed riveted chain rings from a couple of old mountain bikes.
The rings...like yours...were steel and not badly worn.
Just clamping the crank in a vise, and using 1/4 drill was sufficient to leave one swaged ring.
Removing two steel rings saved weight and looked better to my eyes.
Then you can address gearing at the rear hub.
These were old bikes with horizontal drop outs, which was perfect for durable one speeds.
My grand kids use them to ride to the beach. Durable and cheap.
I know this doesn't address your exact question, but you've got some usable parts.
The rings...like yours...were steel and not badly worn.
Just clamping the crank in a vise, and using 1/4 drill was sufficient to leave one swaged ring.
Removing two steel rings saved weight and looked better to my eyes.
Then you can address gearing at the rear hub.
These were old bikes with horizontal drop outs, which was perfect for durable one speeds.
My grand kids use them to ride to the beach. Durable and cheap.
I know this doesn't address your exact question, but you've got some usable parts.
#16
Senior Member
Thread Starter
Join Date: Sep 2017
Location: Eastern Shore, MD
Posts: 2,107
Bikes: Road ready: 1993 Koga Miyata City Liner Touring Hybrid, 1989 Centurion Sport DLX, "I Blame GP" Bridgestone CB-1. Projects: Yea, I got a problem....
Mentioned: 24 Post(s)
Tagged: 0 Thread(s)
Quoted: 753 Post(s)
Liked 737 Times
in
422 Posts
Just wanted to follow up on this. I just destroyed one of these cranks trying to get it apart. I ended up snapping one of the bolt arms off the crank. From what I can tell the the middle and granny ring that are separately riveted to the crank are necessary to back up the 94 BCD outer arms. I'm sure I could do a less destructive disassembly the second time but I don't think I'd trust the arms. I also got to take apart another low end steel ring SR 94 BCD crank with bolted rings, but a couple of the arms were cracked at the bolt holes, so I'm not thinking that low end 94 BCD cranksets are worth messing with.
Likes For bark_eater: