Go Back  Bike Forums > Bike Forums > Bicycle Mechanics
Reload this Page >

Where do you guys store your nuts and stuff

Notices
Bicycle Mechanics Broken bottom bracket? Tacoed wheel? If you're having problems with your bicycle, or just need help fixing a flat, drop in here for the latest on bicycle mechanics & bicycle maintenance.

Where do you guys store your nuts and stuff

Old 07-31-19, 08:31 AM
  #1  
TestyAnt
Newbie
Thread Starter
 
Join Date: Jul 2019
Posts: 3
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Where do you guys store your nuts and stuff

Not nutsacks. But when working on a bicycle, where do you store your nuts/little parts? I am new to all this, but usually have different cups. Like for the derailleur i'll label it derailleur and just put everything for it in there.
TestyAnt is offline  
Old 07-31-19, 08:48 AM
  #2  
pdlamb
Senior Member
 
Join Date: Dec 2010
Location: northern Deep South
Posts: 8,847

Bikes: Fuji Touring, Novara Randonee

Mentioned: 36 Post(s)
Tagged: 0 Thread(s)
Quoted: 2577 Post(s)
Liked 1,900 Times in 1,192 Posts
I think the only time I take a derailer apart, the jockey wheel and nut stay on the table while I'm greasing the bearing. (Ditto Campy shifter parts during a rebuild.) Bottom line, I don't have parts for my parts lying around, and things like brake pads or cleats can stay in the box or bag they came in until I'm ready to use them.

Common things like M5 bolts live in zip-lock plastic bags. Since I don't have to look for one very often, I don't mind digging.
pdlamb is offline  
Old 07-31-19, 09:26 AM
  #3  
Unca_Sam
The dropped
 
Unca_Sam's Avatar
 
Join Date: Oct 2018
Location: Columbus, OH
Posts: 2,406

Bikes: Pake C'Mute Touring/Commuter Build, 1989 Kona Cinder Cone, 1995 Trek 5200, 1973 Raleigh Super Course FG, 1960/61 Montgomery Ward Hawthorne "thrift" 3 speed, by Hercules (sold) : 1966 Schwinn Deluxe Racer (sold)

Mentioned: 10 Post(s)
Tagged: 0 Thread(s)
Quoted: 1739 Post(s)
Liked 1,014 Times in 696 Posts
Agree

Originally Posted by pdlamb
I think the only time I take a derailer apart, the jockey wheel and nut stay on the table while I'm greasing the bearing. (Ditto Campy shifter parts during a rebuild.) Bottom line, I don't have parts for my parts lying around, and things like brake pads or cleats can stay in the box or bag they came in until I'm ready to use them.

Common things like M5 bolts live in zip-lock plastic bags. Since I don't have to look for one very often, I don't mind digging.
+1 on this. If I can't finish the job, I'll reassemble off the bike by just a few turns off the bolt or screw. If it needs to sit in degreaser or evaporust, each component will have its own #5 PP takeout container while they finish the bath.

I only work on one bike at a time though.
Unca_Sam is offline  
Old 07-31-19, 09:30 AM
  #4  
himespau 
Senior Member
 
himespau's Avatar
 
Join Date: Jun 2008
Location: Louisville, KY
Posts: 13,553
Mentioned: 33 Post(s)
Tagged: 0 Thread(s)
Quoted: 4196 Post(s)
Liked 2,913 Times in 1,781 Posts
I do need to get some sort of container for my common-sized nuts and bolts. My dad has these boxes with pull out clear drawers (maybe 2"x2"x8") that I've been jealous of for a long time. Need to find some like those.
himespau is offline  
Old 07-31-19, 09:58 AM
  #5  
WizardOfBoz
Generally bewildered
 
WizardOfBoz's Avatar
 
Join Date: Aug 2015
Location: Eastern PA, USA
Posts: 3,036

Bikes: 2014 Trek Domane 6.9, 1999 LeMond Zurich, 1978 Schwinn Superior

Mentioned: 20 Post(s)
Tagged: 0 Thread(s)
Quoted: 1152 Post(s)
Liked 340 Times in 250 Posts
There are magnetic cups for putting small parts in. Alternately, get a 2 gallon zip-lock plastic bag and do disassembly of small parts inside the bag. This prevents a small spring from going ballistic and embedding invisibly in the carpet 10 feet away.

WizardOfBoz is offline  
Old 07-31-19, 10:05 AM
  #6  
Alexbn921
Junior Member
 
Alexbn921's Avatar
 
Join Date: Jul 2019
Posts: 9
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 1 Time in 1 Post
I use zip lock bags and plastic cups from a parts holder. On my work stand I use the feedback tray and a magnetic tray mounted to the top of the stand.
Alexbn921 is offline  
Old 07-31-19, 10:19 AM
  #7  
RGMN
Senior Member
 
Join Date: Feb 2018
Posts: 565
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 241 Post(s)
Liked 231 Times in 152 Posts
I use a bunch of Ikea kid's plates to hold parts and assemblies. They are cheap, something like 4 for $2, large enough to hold a brake or derailleur, unbreakable, and cheap enough that if I damage one I don't feel to bad about tossing it. I also have a few divided plates for separating the parts when working on something. (The ones I have are actually square, not circular.)
RGMN is offline  
Old 07-31-19, 10:24 AM
  #8  
Clyde1820
Senior Member
 
Join Date: May 2014
Location: USA
Posts: 1,944

Bikes: 1996 Trek 970 ZX Single Track 2x11

Mentioned: 8 Post(s)
Tagged: 0 Thread(s)
Quoted: 610 Post(s)
Liked 558 Times in 423 Posts
A handful of dinky Tupperware-like containers work fairly well. One for all nuts/bolts/parts related to the derailleur. Another for hub parts. Etc. Can be closes with the lid, labeled and stored for easy visual identification later, if postponing re-use of those parts. Larger tube for larger assemblies.

Haven't needed much else, over the years.
Clyde1820 is offline  
Old 07-31-19, 10:31 AM
  #9  
Digger Goreman
Quidam Bike Super Hero
 
Digger Goreman's Avatar
 
Join Date: Jan 2019
Location: Stone Mountain, GA (Metro Atlanta, East)
Posts: 1,150

Bikes: 1995 Trek 800 Sport, aka, "CamelTrek"

Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 331 Post(s)
Liked 415 Times in 282 Posts
Anything at hand, though cardboard egg cartons would certainly absorb the grease and oily fluids....
Digger Goreman is offline  
Old 07-31-19, 11:05 AM
  #10  
pdlamb
Senior Member
 
Join Date: Dec 2010
Location: northern Deep South
Posts: 8,847

Bikes: Fuji Touring, Novara Randonee

Mentioned: 36 Post(s)
Tagged: 0 Thread(s)
Quoted: 2577 Post(s)
Liked 1,900 Times in 1,192 Posts
Originally Posted by WizardOfBoz
Alternately, get a 2 gallon zip-lock plastic bag and do disassembly of small parts inside the bag. This prevents a small spring from going ballistic and embedding invisibly in the carpet 10 feet away.
That's a brilliant idea!
pdlamb is offline  
Old 07-31-19, 11:06 AM
  #11  
himespau 
Senior Member
 
himespau's Avatar
 
Join Date: Jun 2008
Location: Louisville, KY
Posts: 13,553
Mentioned: 33 Post(s)
Tagged: 0 Thread(s)
Quoted: 4196 Post(s)
Liked 2,913 Times in 1,781 Posts
Originally Posted by WizardOfBoz
There are magnetic cups for putting small parts in. Alternately, get a 2 gallon zip-lock plastic bag and do disassembly of small parts inside the bag. This prevents a small spring from going ballistic and embedding invisibly in the carpet 10 feet away.
Yeah, I have a park one of those on my stand for immediately used stuff. By no means is the Park one necessary (or even better than others), it was just available when I needed a new one..
himespau is offline  
Old 07-31-19, 11:17 AM
  #12  
Phil_gretz
Zip tie Karen
 
Phil_gretz's Avatar
 
Join Date: Aug 2009
Location: Fair Oaks Ranch, TX
Posts: 7,006

Bikes: '13 Motobecane Fantom29 HT, '16 Motobecane Turino Pro Disc, '18 Velobuild VB-R-022, '21 Tsunami SNM-100

Mentioned: 26 Post(s)
Tagged: 0 Thread(s)
Quoted: 1465 Post(s)
Liked 1,542 Times in 806 Posts
During a re-build, I get out a fresh copier paper box and set it within its inverted lid. Then individual components go into the box. Disassembled or loose parts go within Ziploc baggies and then into the box (headsets, bottom bracket bearings, loose downtube shifters). Then any new cables, chains, bar tape, whatever go into the box. I then can start on the frame without any loose things bouncing about.

For long-term storage of loose and sundry items, I have a stack of compartmentalized lidded trays that hold everything: One for bearings, another for cable housing parts and brake parts, another for larger items like replacement derailleur pulleys, spacers, lockrings, pump pegs and the like, and one more for fasteners.

All long-term component storage is in individually labeled shoe boxes by component type: derailleurs, cranksets/bb, brake, cable housing, pedals, handlebar tape/plugs, shifters. This system is patterned after Marie Condo's method, and it really works well. It's simple to find anything in seconds.
Phil_gretz is offline  
Old 07-31-19, 11:20 AM
  #13  
AnkleWork
Senior Member
 
Join Date: Jan 2013
Location: Llano Estacado
Posts: 3,702

Bikes: old clunker

Mentioned: 13 Post(s)
Tagged: 0 Thread(s)
Quoted: 684 Post(s)
Likes: 0
Liked 104 Times in 82 Posts
Suckers.
AnkleWork is offline  
Old 07-31-19, 12:09 PM
  #14  
WizardOfBoz
Generally bewildered
 
WizardOfBoz's Avatar
 
Join Date: Aug 2015
Location: Eastern PA, USA
Posts: 3,036

Bikes: 2014 Trek Domane 6.9, 1999 LeMond Zurich, 1978 Schwinn Superior

Mentioned: 20 Post(s)
Tagged: 0 Thread(s)
Quoted: 1152 Post(s)
Liked 340 Times in 250 Posts
Originally Posted by pdlamb
That's a brilliant idea!
I think it's been used by a lot of folks. I first read about it in "Repair of Mechanical Dial Indicators and Calipers", by Michael Yamamoto.
WizardOfBoz is offline  
Old 07-31-19, 12:15 PM
  #15  
Brocephus
Professional amateur
 
Brocephus's Avatar
 
Join Date: May 2018
Location: Ga.
Posts: 665

Bikes: Does a Big Wheel count ?

Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 295 Post(s)
Liked 133 Times in 89 Posts
Yep, the big bag thing is a good idea,(it's also commonly used when working on firearm parts that have tiny springs), but another good idea is to have a big retrieval magnet on hand, that you can wave over a wide area or carpet or flooring, and pick up tiny steel parts. They're not very expensive, but can be real handy.
Mine looks a lot like this one.....https://www.sportsmansguide.com/prod...agnet?a=679952
(I actually got turned onto these things while crewing on boats, they're used to rescue tools and other stuff that may have fallen into the silty bottom from the pier or boat.)

Last edited by Brocephus; 07-31-19 at 12:19 PM.
Brocephus is offline  
Old 08-01-19, 05:59 AM
  #16  
HillRider
Senior Member
 
Join Date: Aug 2005
Location: Pittsburgh, PA
Posts: 33,656

Bikes: '96 Litespeed Catalyst, '05 Litespeed Firenze, '06 Litespeed Tuscany, '20 Surly Midnight Special, All are 3x10. It is hilly around here!

Mentioned: 39 Post(s)
Tagged: 0 Thread(s)
Quoted: 2026 Post(s)
Likes: 0
Liked 1,095 Times in 741 Posts
For organized storage of small parts like nuts, bolts, washers, bearing balls, etc. a multi drawer small cabinet is extremely useful. Here is an example: https://www.homedepot.com/p/Stalwart...7422/205190694

This one is a bit large for just bicycle items but I use a similar one to organize all of my SAE and Metric fasteners, bearing balls and miscellaneous small hardware items. There are smaller versions with fewer drawers at lower cost.
HillRider is offline  
Old 08-01-19, 06:59 AM
  #17  
robert schlatte
Senior Member
 
robert schlatte's Avatar
 
Join Date: Dec 2007
Location: columbus, ohio
Posts: 895

Bikes: Soma Saga, 1980 Schwinn Voyageur 11.8, New Albion Privateer

Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 76 Post(s)
Likes: 0
Liked 9 Times in 7 Posts
I have a multi drawer cabinet as well which I store small parts in. Very useful. When I am working on a bike and want to keep small parts in one place I use the lids off old peanut butter jars as holders.
robert schlatte is offline  
Old 08-01-19, 07:19 AM
  #18  
Litespud
Senior Member
 
Join Date: Oct 2017
Location: Chapel Hill NC
Posts: 1,683

Bikes: 2000 Litespeed Vortex Chorus 10, 1995 DeBernardi Cromor S/S

Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 645 Post(s)
Liked 797 Times in 446 Posts
Harbor freight usually has a bunch of small parts storage solutions for less $ than the big box hardware stores
Litespud is offline  
Old 08-02-19, 02:57 AM
  #19  
JoeTBM 
Droid on a mission
 
JoeTBM's Avatar
 
Join Date: May 2018
Location: Palm Coast, FL
Posts: 1,002

Bikes: Diamondback Wildwood Classic

Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 315 Post(s)
Liked 276 Times in 191 Posts
Originally Posted by Litespud
Harbor freight usually has a bunch of small parts storage solutions for less $ than the big box hardware stores
We use these for for the smaller parts when we do a portable bike repair run

https://www.harborfreight.com/materi...ase-93928.html

You can get them for about $6 when they run their coupon special
__________________
JoeTBM (The Bike Man) - I'm a black & white type of guy, the only gray in my life is the hair on my head
www.TheBikeMenOfFlaglerCounty.com




JoeTBM is offline  
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
frndlyfire
Classic & Vintage
7
08-11-19 12:26 PM
SB739
Bicycle Mechanics
16
04-19-17 04:36 PM
jimmuller
Classic & Vintage
12
12-16-10 06:35 AM
buldogge
Classic & Vintage
0
03-25-10 10:07 PM
chico1st
Bicycle Mechanics
14
01-11-10 10:25 PM

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.