Out of the box- tools?
#1
Senior Member
Thread Starter
Join Date: Jul 2018
Posts: 89
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 50 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Out of the box- tools?
What kind of tools do I need to buy before ordering a bike out of the box? I can't find information on youtube that tells what I need to prepare. Thanks.
#2
Super Moderator
Join Date: Jul 2004
Location: Ffld Cnty Connecticut
Posts: 21,843
Bikes: Old Steelies I made, Old Cannondales
Mentioned: 12 Post(s)
Tagged: 0 Thread(s)
Quoted: 1173 Post(s)
Liked 927 Times
in
612 Posts
Depends on the bike. Most assembly is done.
4,5,6 mm allen wrenches
8,9,10 mm box wrenches.
spoke wrench to properly tension spokes.
15 mm pedal wrench.
4,5,6 mm allen wrenches
8,9,10 mm box wrenches.
spoke wrench to properly tension spokes.
15 mm pedal wrench.
__________________
Bikes: Old steel race bikes, old Cannondale race bikes, less old Cannondale race bike, crappy old mtn bike.
FYI: https://www.bikeforums.net/forum-sugg...ad-please.html
Bikes: Old steel race bikes, old Cannondale race bikes, less old Cannondale race bike, crappy old mtn bike.
FYI: https://www.bikeforums.net/forum-sugg...ad-please.html
#3
Senior Member
Join Date: Aug 2005
Location: Pittsburgh, PA
Posts: 33,656
Bikes: '96 Litespeed Catalyst, '05 Litespeed Firenze, '06 Litespeed Tuscany, '20 Surly Midnight Special, All are 3x10. It is hilly around here!
Mentioned: 39 Post(s)
Tagged: 0 Thread(s)
Quoted: 2026 Post(s)
Likes: 0
Liked 1,096 Times
in
742 Posts
Most important tool: Adequate knowledge as to how to finish assembling and adjusting it. If you are not reasonably familiar with how a bike works, get competent help from either a knowledgable friend or take it to a bike shop and pay to have it done correctly. Your riding enjoyment and, more importantly, your safety depend on it.
#5
Senior Member
Join Date: Oct 2017
Location: Chapel Hill NC
Posts: 1,683
Bikes: 2000 Litespeed Vortex Chorus 10, 1995 DeBernardi Cromor S/S
Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 645 Post(s)
Liked 797 Times
in
446 Posts
Most pedals now use an allen wrench through the back of the spindle - could be as large as 8mm. I think you could do almost everything with a set of metric allen wrenches, a set of metric open-end wrenches, up to maybe 12mm, and a pair of reasonably fine straight- and Philips-head screwdrivers. If there are any carbon parts in your setup, you should consider a low range torque wrench and some small (4-5mm) allen bits, or, if you're not familiar with using a torque wrench, definitely get a knowledgable friend or take it to a shop
#6
Senior Member
#7
Junior Member
Join Date: Sep 2018
Posts: 19
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 2 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
- Box cutter or scissors.
- Hex wrench set (typically 6mm, 5mm and 4mm wrenches are required)
- Pedal wrench.
- Cable cutters.
- Bike grease.
- Bike stand (preferred)
- Bike pump.
- Philips Head screw driver.
#8
Junior Member
#9
Senior Member
Join Date: Jul 2006
Location: San Jose (Willow Glen) Ca
Posts: 9,842
Bikes: Kirk Custom JK Special, '84 Team Miyata,(dura ace old school) 80?? SR Semi-Pro 600 Arabesque
Mentioned: 106 Post(s)
Tagged: 0 Thread(s)
Quoted: 2337 Post(s)
Liked 2,821 Times
in
1,540 Posts
Understand that while many out of the box bikes are OK, the whole bike should be checked..... are hubs, headset, etc greased? are the wheels true? are the brakes working an adjusted correctly? are the gears properly adjusted and working? Bike shops do this for the bike they put together to sell
Some (or in reality a lot of this) will depend on where you are sourcing your bike from..... a company like Canyon which has a high end direct salesmodel, including needed manual, support, tools and torque wrench as an example or Bikes direct that is the super low cost model that does not include a lot
the OP's basic question suggests that the OP does not have a lot of bike wrenching knowledge. Unless are ordering a high end direct sales model bike, strong suggestion is to take the boxed bike to a shop and pay them to assemble. Add that to overall cost when comparing prices.
Some (or in reality a lot of this) will depend on where you are sourcing your bike from..... a company like Canyon which has a high end direct salesmodel, including needed manual, support, tools and torque wrench as an example or Bikes direct that is the super low cost model that does not include a lot
the OP's basic question suggests that the OP does not have a lot of bike wrenching knowledge. Unless are ordering a high end direct sales model bike, strong suggestion is to take the boxed bike to a shop and pay them to assemble. Add that to overall cost when comparing prices.
__________________
Life is too short not to ride the best bike you have, as much as you can
(looking for Torpado Super light frame/fork or for Raleigh International frame fork 58cm)
Life is too short not to ride the best bike you have, as much as you can
(looking for Torpado Super light frame/fork or for Raleigh International frame fork 58cm)
#10
Super Moderator
Join Date: Jul 2004
Location: Ffld Cnty Connecticut
Posts: 21,843
Bikes: Old Steelies I made, Old Cannondales
Mentioned: 12 Post(s)
Tagged: 0 Thread(s)
Quoted: 1173 Post(s)
Liked 927 Times
in
612 Posts
Grease the pedal threads before installing. Left side pedal is left hand thread. Make them snug, but no need to be a gorilla tightening them. Just harder to get off later.
__________________
Bikes: Old steel race bikes, old Cannondale race bikes, less old Cannondale race bike, crappy old mtn bike.
FYI: https://www.bikeforums.net/forum-sugg...ad-please.html
Bikes: Old steel race bikes, old Cannondale race bikes, less old Cannondale race bike, crappy old mtn bike.
FYI: https://www.bikeforums.net/forum-sugg...ad-please.html
#11
Senior Member
Thread Starter
Join Date: Jul 2018
Posts: 89
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 50 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
no lubricant. All purpose grease from auto store will work?
#12
Senior Member
Join Date: Oct 2007
Location: West Yorkshire, United Kingdom
Posts: 5,773
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 453 Post(s)
Liked 104 Times
in
87 Posts
the OP's basic question suggests that the OP does not have a lot of bike wrenching knowledge. Unless are ordering a high end direct sales model bike, strong suggestion is to take the boxed bike to a shop and pay them to assemble. Add that to overall cost when comparing prices.