V-brake rubs on one side, then the other
#1
Member
Thread Starter
Join Date: Oct 2018
Posts: 32
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 19 Post(s)
Liked 0 Times
in
0 Posts
V-brake rubs on one side, then the other
I adjust my v-brake so that neither side rubs. The next day it starts rubbing on one side, so I adjust it so that it stops rubbing. Then the day after that it starts rubbing on the other side. So I adjust it again and then a day later it starts rubbing again on the side it rubbed on two days before. And so it goes on in an endless loop. How do I fix this?
#2
Senior Member
Join Date: Oct 2015
Location: San Diego, California
Posts: 4,077
Bikes: Velo Orange Piolet
Mentioned: 28 Post(s)
Tagged: 0 Thread(s)
Quoted: 2228 Post(s)
Liked 2,011 Times
in
972 Posts
Maybe take the brake arms off the posts, clean the bearing surfaces up, regrease, and reassemble. It's fairly easy.
Likes For tyrion:
#3
Senior Member
Join Date: Aug 2005
Location: Las Vegas, NV
Posts: 932
Bikes: '04 LeMond Buenos Aires, '82 Bianchi Nuova Racing, De Rosa SLX, Bridgestone MB-1, Guerciotti TSX, Torpado Aelle, LeMond Tourmalet 853, Bridgestone Radac
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 101 Post(s)
Liked 46 Times
in
36 Posts
I like V-brakes but they can change their mind quickly. It seems that whenever I undo them to remove a wheel, they never center the same and I have to mess with the springs.
#4
SE Wis
Join Date: Apr 2005
Location: Milwaukee, WI
Posts: 10,501
Bikes: '68 Raleigh Sprite, '02 Raleigh C500, '84 Raleigh Gran Prix, '91 Trek 400, 2013 Novara Randonee, 1990 Trek 970
Mentioned: 40 Post(s)
Tagged: 0 Thread(s)
Quoted: 2742 Post(s)
Liked 3,389 Times
in
2,052 Posts
Any time I adjust them I squeeze the brakes a bunch of times before I call it good.
#5
Member
Thread Starter
Join Date: Oct 2018
Posts: 32
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 19 Post(s)
Liked 0 Times
in
0 Posts
#7
Really Old Senior Member
Petroleum jelly.
It probably won't last as long as a "dedicated grease", but it's not like an axle constantly rotating.
It's good enough to see if lubrication is the problem.
Last edited by Bill Kapaun; 07-19-19 at 02:24 PM.
#8
aka Tom Reingold
Join Date: Jan 2009
Location: New York, NY, and High Falls, NY, USA
Posts: 40,498
Bikes: 1962 Rudge Sports, 1971 Raleigh Super Course, 1971 Raleigh Pro Track, 1974 Raleigh International, 1975 Viscount Fixie, 1982 McLean, 1996 Lemond (Ti), 2002 Burley Zydeco tandem
Mentioned: 511 Post(s)
Tagged: 0 Thread(s)
Quoted: 7346 Post(s)
Liked 2,453 Times
in
1,430 Posts
You might try disconnecting the springs from the arms, bending them out so they push out harder, then putting them back. You'll need some trial and error to get the spring tensions approximately equal. I've done this, and it works. But yeah, V-brakes are annoying in this way.
__________________
Tom Reingold, tom@noglider.com
New York City and High Falls, NY
Blogs: The Experienced Cyclist; noglider's ride blog
“When man invented the bicycle he reached the peak of his attainments.” — Elizabeth West, US author
Please email me rather than PM'ing me. Thanks.
Tom Reingold, tom@noglider.com
New York City and High Falls, NY
Blogs: The Experienced Cyclist; noglider's ride blog
“When man invented the bicycle he reached the peak of his attainments.” — Elizabeth West, US author
Please email me rather than PM'ing me. Thanks.
Likes For noglider:
#9
Really Old Senior Member
Does it "switch sides" depending on how quickly you release the lever?
#10
Senior Member
Join Date: Jun 2008
Location: Shawnee, KS
Posts: 273
Bikes: Bike Friday NWT, Rans Stratus, Cannondale R500, trek 720 multitrack, Rockhopper
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 35 Post(s)
Liked 36 Times
in
22 Posts
A problem I had with v brakes once was that, as they wear they are moving in an arc, this makes them move slowly downward on the rim as the wear progresses, after a while a portion of the pad is no longer in contact with the rim and develops a lip. This lip can catch on the rim causing them not to release properly. This and has been mentioned brake posts with no lube and cabling have caused most of my v brake issues.
#11
Droid on a mission
Join Date: May 2018
Location: Palm Coast, FL
Posts: 1,005
Bikes: Diamondback Wildwood Classic
Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 317 Post(s)
Liked 280 Times
in
195 Posts
I use fine steel wool on the bosses and a .38 caliber brass gun barrel brush inside. Once all nice and shiny, lube and reassemble, work's like new
__________________
JoeTBM (The Bike Man) - I'm a black & white type of guy, the only gray in my life is the hair on my head
www.TheBikeMenOfFlaglerCounty.com
JoeTBM (The Bike Man) - I'm a black & white type of guy, the only gray in my life is the hair on my head
www.TheBikeMenOfFlaglerCounty.com
#12
Steel is real
Usually if i need to tighten an adjust screw - i'll loosen the other side. (depends)
#13
Senior Member
Join Date: Nov 2014
Location: Eastern Iowa
Posts: 631
Bikes: 2014 Trek Allant drop bar conversion, modified Schwinn MTN commuter, 2015 Trek 520, Soma ES, Salsa Journeyman, 1980 Trek 414
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 178 Post(s)
Liked 355 Times
in
166 Posts
Are you sure that the locknut and cone on your wheel hub has not worked loose? Make sure there is no play in the hub when the wheel is affixed in the dropout, as this can make it seem like the brakes are coming out of adjustment when the wheel 'wobbles' back and forth due to the play in the hub bearings.
#14
Senior Member
Join Date: Jun 2005
Location: Kentucky
Posts: 2,599
Bikes: 06 Lemond Reno, 98 GT Timberline mtn.bike
Mentioned: 8 Post(s)
Tagged: 0 Thread(s)
Quoted: 426 Post(s)
Liked 699 Times
in
436 Posts
The bending of the spring is one way to increase tension, and if that doesn't do it, assuming your frame has different holes on the brake mounting post, change the hole position to increase tension.