Go Back  Bike Forums > Bike Forums > Cyclocross and Gravelbiking (Recreational)
Reload this Page >

Thinking of making a radical drivetrain change

Notices
Cyclocross and Gravelbiking (Recreational) This has to be the most physically intense sport ever invented. It's high speed bicycle racing on a short off road course or riding the off pavement rides on gravel like : "Unbound Gravel". We also have a dedicated Racing forum for the Cyclocross Hard Core Racers.

Thinking of making a radical drivetrain change

Old 06-28-19, 07:40 PM
  #1  
PhoenixBiker 
Senior Member
Thread Starter
 
Join Date: Jul 2018
Location: Huntington, West Virginia, USA
Posts: 110

Bikes: 2001 Waterford RST-22, 2002 Gunnar Sport, 1999 Trek 520 gravel grinder

Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 35 Post(s)
Likes: 0
Liked 5 Times in 3 Posts
Thinking of making a radical drivetrain change

This is a road-bike question, but I'm posting it in the Cyclocross/Gravelbiking forum because it involves cross/gravel gearing.

For close to 20 years, I've run old-fashioned road triples on both my road bikes (one Waterford, one Gunnar) On both, I run Ultegra 52/42/26 setups with 13-36 cassettes. At age 64, after back surgery and two bouts with cancer, I can no longer push big gears. I'm thinking of changing the gears on one of the bikes to more of a cyclocross/gravel setup. I'm looking at replacing the current triple crankset with a White Industries VBC (variable bolt circle) double crankset that combines a 44T big ring with at 24T small ring. I'd couple that with 11-speed SRAM shifters / derailleurs and an 11-42T cassette.

Does anyone see any potential pitfalls in such a setup? It won't be cheap ($1k or thereabouts), but I think it will give me the low gearing I need to climb the short-but-steep hills I ride here in West Virginia. Your thoughts? Thanks!
PhoenixBiker is offline  
Old 06-28-19, 08:26 PM
  #2  
PhoenixBiker 
Senior Member
Thread Starter
 
Join Date: Jul 2018
Location: Huntington, West Virginia, USA
Posts: 110

Bikes: 2001 Waterford RST-22, 2002 Gunnar Sport, 1999 Trek 520 gravel grinder

Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 35 Post(s)
Likes: 0
Liked 5 Times in 3 Posts
Originally Posted by Spoonrobot
You want to use a SRAM front derailleur to shift a 20 tooth front gap?
I'm not sure it could. That's why I'm asking for input from people with experience in such things. The White Ind. website says the cranks are capable of 20T jumps, but I wasn't sure the FD could. Worst case, I could go 40/24. That's a 16T jump, which should be doable. My current setup makes the 42-26 jump with ease.
PhoenixBiker is offline  
Old 06-28-19, 10:34 PM
  #3  
tyrion
Senior Member
 
tyrion's Avatar
 
Join Date: Oct 2015
Location: San Diego, California
Posts: 4,077

Bikes: Velo Orange Piolet

Mentioned: 28 Post(s)
Tagged: 0 Thread(s)
Quoted: 2228 Post(s)
Liked 2,011 Times in 972 Posts
Originally Posted by PhoenixBiker
...44T big ring with at 24T small ring. I'd couple that with 11-speed SRAM shifters / derailleurs and an 11-42T cassette.
I don't think any RD can suck up enough chain to handle that. If the chain is long enough to handle 44t chainring and 42t cog, then it will be dangling in the 24t chainring and 11t cog (not catastrophic, just sloppy).

If you can fit a 44-32-22 mountain crank, with a 36t cassette (very common, unexotic setup), that gets almost as low as a 24t chainring and 42t cog.
tyrion is offline  
Old 06-28-19, 11:22 PM
  #4  
Rvav8r
Senior Member
 
Join Date: May 2012
Location: Bandon, Oregon
Posts: 106

Bikes: 2019 Ibis Hakka MX, 2011 Giant Defy 3 Composite, 2012 Specialized Hardrock

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 11 Post(s)
Liked 1 Time in 1 Post
I just got my Hakka MX 1x11 bike today. I was a little skeptical about only having a single chain ring but I can tell you I love it. I have a 40t front and a 11-42 cassette in the back. I was able to spin up to 23 mph on the flat and climb an 18% hill that I use to have to "paperboy" up. This time I was able to stay in the saddle. I'm 70 and while I can push a big gear I just don't have the cadence ability anymore. I'm a diesel, not a turbo.
Rvav8r is offline  
Old 06-28-19, 11:43 PM
  #5  
Cyclist0108
Occam's Rotor
 
Join Date: Jul 2013
Posts: 7,248
Mentioned: 61 Post(s)
Tagged: 0 Thread(s)
Quoted: 2366 Post(s)
Liked 2,331 Times in 1,164 Posts
I have a 46/30T White Industries crank with my Shimano (Di2) derailleur, and an 11-36T cassette on one of my wheel-sets. Shimano's derailleurs can handle this. My limited experiences with SRAM leads me to suggest avoiding it. They introduced the 1X because they never quite got the front derailleur thing right.

Get Shimano Di2 Ultegra. You won't regret it.
Cyclist0108 is offline  
Old 06-29-19, 07:30 AM
  #6  
DrIsotope
Non omnino gravis
 
DrIsotope's Avatar
 
Join Date: Feb 2015
Location: SoCal, USA!
Posts: 8,553

Bikes: Nekobasu, Pandicorn, Lakitu

Mentioned: 119 Post(s)
Tagged: 0 Thread(s)
Quoted: 4905 Post(s)
Liked 1,731 Times in 958 Posts
I know the hills might be steep, but 24/42 @ 75rpm is 3.5mph. That is decidedly "get off and walk" pace. I would split the difference and just go 1x11 with a 38T or a 40T in the front and call it a day. Wouldn't even need to change the crankset.
__________________
DrIsotope is offline  
Old 06-29-19, 10:58 AM
  #7  
fronesis
Senior Member
 
Join Date: Aug 2013
Posts: 141
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 45 Post(s)
Liked 8 Times in 6 Posts
Originally Posted by DrIsotope
I know the hills might be steep, but 24/42 @ 75rpm is 3.5mph. That is decidedly "get off and walk" pace. I would split the difference and just go 1x11 with a 38T or a 40T in the front and call it a day. Wouldn't even need to change the crankset.
This is EXACTLY my recommendation too. If this bike is for the road, and not gravel, then even on super steep hills, a low gear of 38/42 is plenty low. Yes, that doesn’t give you a ton of top end, but you won’t spin out the 38/11 until you are up above 30mph. And given what you say about your riding, that doesn’t seem like a big problem. In return, you get a MUCH simpler setup.
fronesis is offline  
Old 06-29-19, 11:43 AM
  #8  
BluesDawg
just keep riding
 
BluesDawg's Avatar
 
Join Date: Feb 2005
Location: Milledgeville, Georgia
Posts: 13,560

Bikes: 2018 Black Mountain Cycles MCD,2017 Advocate Cycles Seldom Seen Drop Bar, 2017 Niner Jet 9 Alloy, 2015 Zukas custom road, 2003 KHS Milano Tandem, 1986 Nishiki Cadence rigid MTB, 1980ish Fuji S-12S

Mentioned: 15 Post(s)
Tagged: 0 Thread(s)
Quoted: 173 Post(s)
Liked 33 Times in 22 Posts
Originally Posted by wgscott
I have a 46/30T White Industries crank with my Shimano (Di2) derailleur, and an 11-36T cassette on one of my wheel-sets. Shimano's derailleurs can handle this. My limited experiences with SRAM leads me to suggest avoiding it. They introduced the 1X because they never quite got the front derailleur thing right.

Get Shimano Di2 Ultegra. You won't regret it.
My 46/30 Sugino crank with SRAM Rival 22 and 11-36 cassette works without a hitch. Following the setup instructions for the yaw FD is critical as it is slightly different from what you may be used to doing with other derailleurs.

With the White crank, you might try 26/42 rings and experiment with cassettes to see what your RD will manage. 11-42 would be close to what you wanted on the low end, but even if you had to go with 11-40 or 11-36 you would be in better shape than with the 1x setups suggested.

Last edited by BluesDawg; 06-29-19 at 11:58 AM.
BluesDawg is offline  
Old 06-29-19, 06:40 PM
  #9  
PhoenixBiker 
Senior Member
Thread Starter
 
Join Date: Jul 2018
Location: Huntington, West Virginia, USA
Posts: 110

Bikes: 2001 Waterford RST-22, 2002 Gunnar Sport, 1999 Trek 520 gravel grinder

Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 35 Post(s)
Likes: 0
Liked 5 Times in 3 Posts
Thanks for your input, everyone! I appreciate it; and I'll let you know what I decide.
PhoenixBiker is offline  
Old 06-29-19, 09:34 PM
  #10  
jan nikolajsen 
Mostly Mischief
 
jan nikolajsen's Avatar
 
Join Date: Apr 2008
Location: Moab, Utah
Posts: 1,500
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 37 Post(s)
Liked 58 Times in 24 Posts
Guys, 1x is not the solution for every situation! Especially true when addressing riders loosing power due to age or other circumstances.

He currently runs 26-36 (roughly 19 gear inches) and is asking for a combo giving him something lower. The 1x advice presented above is 23.8 gear inches. Huh? Just get off and walk?

The way forward from here is finding a long cage rear derailleur capable of the most chain wrap. Once that number is established start looking at the cassette/chainring combo that gives both a deep gear and reasonable top end speed.
jan nikolajsen is offline  
Old 07-01-19, 08:00 AM
  #11  
Caliper
Senior Member
 
Join Date: May 2014
Location: Michigan
Posts: 990

Bikes: Many

Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 385 Post(s)
Liked 58 Times in 43 Posts
Originally Posted by jan nikolajsen
Guys, 1x is not the solution for every situation!
Heck, it's not really a great solution for most situations. More a specialized solution for certain situations with limited use cases (CX only, singletrack only, etc). 1x is a compromise situation everywhere else, IMO.


Anyways, for the OP when you say you can't push big gears anymore, are you referring to just the 52T or do you ALSO need lower low end? Your current 26x36 low gear is too much? Reason being that there are MTB doubles with a 26T small ring which could be paired with a 11-36 to keep your same low gearing and actually not lost too much top end due to the 11T. If you really do need the lower gears, I can attest that a 42/28 crank with 11-42 cassette DOES work with a long cage RD. All SRAM parts, but it is "only" 10sp.
Caliper is offline  
Old 07-01-19, 08:09 AM
  #12  
HarborBandS
HarborBandS
 
Join Date: Jun 2018
Location: Chicago Western Suburbs
Posts: 477
Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 266 Post(s)
Liked 104 Times in 57 Posts
I would look at the gears you spend the most time with now and note the ratios. Then make sure whatever you switch to has these in its range and then some.

2x11 should give you plenty of low gear climbing options if you use a compact crank and put a larger cassette on the back. I feel like triple chain rings are a hold over from the days of 53t chain rings and smaller cassettes.
HarborBandS is offline  
Old 07-01-19, 09:54 AM
  #13  
wsteve464
Senior Member
 
Join Date: Jul 2016
Posts: 561
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 161 Post(s)
Liked 71 Times in 62 Posts
If you have the budget and are somewhat mechanical, think about going Shimano mtb Di2 I did and don't want to use anything else. You can use climbing shifters so no need for new brakes. You can use a Sram 10 spd crank 42/26 with an 11-42 cassette. Shopping around between ebay and the online vendors it should come in under $1500.
wsteve464 is offline  
Old 07-01-19, 08:38 PM
  #14  
HTupolev
Senior Member
 
Join Date: Apr 2015
Location: Seattle
Posts: 4,261
Mentioned: 41 Post(s)
Tagged: 0 Thread(s)
Quoted: 1971 Post(s)
Liked 1,297 Times in 629 Posts
Originally Posted by DrIsotope
I know the hills might be steep, but 24/42 @ 75rpm is 3.5mph. That is decidedly "get off and walk" pace. I would split the difference and just go 1x11 with a 38T or a 40T in the front and call it a day. Wouldn't even need to change the crankset.
If you've got the gears, pedaling is nearly always easier and more efficient than walking. Even at 3.5mph. A hill that slows you down that much isn't going to be a joy to push a bike up; 3.5mph is a brisk walking pace unburdened on flat ground, it's extremely intense on a steep gradient with a bike in hand.
HTupolev is offline  
Likes For HTupolev:
Old 07-01-19, 08:59 PM
  #15  
DrIsotope
Non omnino gravis
 
DrIsotope's Avatar
 
Join Date: Feb 2015
Location: SoCal, USA!
Posts: 8,553

Bikes: Nekobasu, Pandicorn, Lakitu

Mentioned: 119 Post(s)
Tagged: 0 Thread(s)
Quoted: 4905 Post(s)
Liked 1,731 Times in 958 Posts
Having walked up my fair share of dirt hills I found too steep to pedal up, no amount of gearing could have prevented it. I'm not on a mountain bike. At some point, frame geometry and the limitations of the tires become an issue, usually long before the gearing does.

I've never met a paved incline I couldn't manage with a 1 : 1 final. Even that time Google Maps tried to kill me in San Francisco, when it took 300W to do 4mph.
__________________
DrIsotope is offline  
Old 07-02-19, 06:34 AM
  #16  
Hmmm
Full Member
 
Hmmm's Avatar
 
Join Date: Nov 2014
Location: Paris, France
Posts: 399

Bikes: TCX & CAAD3 SAECO

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 147 Post(s)
Liked 118 Times in 66 Posts
Originally Posted by Caliper
Heck, it's not really a great solution for most situations. More a specialized solution for certain situations with limited use cases (CX only, singletrack only, etc). 1x is a compromise situation everywhere else, IMO.
I disagree. 40t with 11-42 is great on road, gravel, single track and CX.
Hmmm is offline  
Old 07-02-19, 06:56 AM
  #17  
Koyote
Senior Member
 
Join Date: Sep 2017
Posts: 7,767
Mentioned: 37 Post(s)
Tagged: 0 Thread(s)
Quoted: 6882 Post(s)
Liked 10,873 Times in 4,637 Posts
Originally Posted by DrIsotope
I know the hills might be steep, but 24/42 @ 75rpm is 3.5mph. That is decidedly "get off and walk" pace. I would split the difference and just go 1x11 with a 38T or a 40T in the front and call it a day. Wouldn't even need to change the crankset.
This. I'm not sure that a 24/42 is usable.


Originally Posted by DrIsotope
Having walked up my fair share of dirt hills I found too steep to pedal up, no amount of gearing could have prevented it. I'm not on a mountain bike. At some point, frame geometry and the limitations of the tires become an issue, usually long before the gearing does.

I've never met a paved incline I couldn't manage with a 1 : 1 final. Even that time Google Maps tried to kill me in San Francisco, when it took 300W to do 4mph.
Ever been to Pittsburgh?
Koyote is offline  
Old 07-02-19, 12:59 PM
  #18  
Caliper
Senior Member
 
Join Date: May 2014
Location: Michigan
Posts: 990

Bikes: Many

Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 385 Post(s)
Liked 58 Times in 43 Posts
Originally Posted by Hmmm
I disagree. 40t with 11-42 is great on road, gravel, single track and CX.

"Great" on road to singletrack? That's a really tall order even if you have flat terrain. I honestly think even a 2x can only be *great* on half that (ie: road and gravel OR gravel and singletrack) but can be good if you are willing to accept some compromise on either end. 1x will compromise on both.


First, you're lacking top end. 40x11 @ 110 rpm on 700x44's = 33mph. So I'm spinning out early on gravel and really early on road. This is a huge dealbreaker to me.


Second 40x42 is 26.5 gear inches on the same tires. This is actually a lower low end than I usually run for gravel but a pretty high gear on a number of the hills on my local singletrack (hey, you claimed singletrack also). Especially when they are covered in pine needles and you need to apply the power smoothly, anything short of a fatbike tire will spin the tires loose with this gearing since you'll be mashing. My current gearing for offroad is about 20 inches on the low end.


Sorry, I've ridden 1x a bit and spent a lot of time on rides with other guys who have it. There isn't a single ride where the 1x riders aren't either spinning out on the downhills or running out of gearing on uphills. I mean, if you're comparing 1x to 2x7 or something then sure, 1x can cover the same range with similar steps, but a 2x with the same number of cogs in the cassette will always have better options than a 1x.
Caliper is offline  
Old 07-02-19, 02:11 PM
  #19  
shoota 
Senior Member
 
shoota's Avatar
 
Join Date: Jun 2012
Location: Stillwater, OK
Posts: 8,128
Mentioned: 33 Post(s)
Tagged: 0 Thread(s)
Quoted: 1871 Post(s)
Liked 689 Times in 467 Posts
Suggesting 1X to OP is crazy talk.
__________________
2014 Cannondale SuperSix EVO 2
2019 Salsa Warbird
shoota is offline  
Old 07-02-19, 08:13 PM
  #20  
DrIsotope
Non omnino gravis
 
DrIsotope's Avatar
 
Join Date: Feb 2015
Location: SoCal, USA!
Posts: 8,553

Bikes: Nekobasu, Pandicorn, Lakitu

Mentioned: 119 Post(s)
Tagged: 0 Thread(s)
Quoted: 4905 Post(s)
Liked 1,731 Times in 958 Posts
As a guy with 15k+ miles with a 1X drivetrain, the armchair pontification about spinning out, not enough gearing range, etc... is hilarious.

Originally Posted by Koyote
Ever been to Pittsburgh?
There's a local stretch of access road that pretty much goes up the side of a hill to get to a reservoir. The climb portion is 0.19 miles long, and gains 190ft of elevation. It averages just over 18% for the whole length, and kicks up to 31% just before the end. It's too steep. It's one of those things you only ride up so you can say that you rode up it. It makes no earthly sense otherwise.
__________________
DrIsotope is offline  
Old 07-02-19, 08:56 PM
  #21  
pinholecam
Senior Member
 
Join Date: Jan 2016
Posts: 627
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 228 Post(s)
Liked 145 Times in 95 Posts
Sram x9 crankset with a Sram Apex 10sp might be viable since you are located in the US and these might still be available.
I wanted to try this option for a recent build, but the local distributor in Singapore does bring in X9 (or other 10sp MTB stuff) .

The X9 crank has a 42/28T option
pinholecam is offline  
Old 07-03-19, 01:23 AM
  #22  
Hmmm
Full Member
 
Hmmm's Avatar
 
Join Date: Nov 2014
Location: Paris, France
Posts: 399

Bikes: TCX & CAAD3 SAECO

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 147 Post(s)
Liked 118 Times in 66 Posts
Originally Posted by Caliper
"Great" on road to singletrack? That's a really tall order even if you have flat terrain. I honestly think even a 2x can only be *great* on half that (ie: road and gravel OR gravel and singletrack) but can be good if you are willing to accept some compromise on either end. 1x will compromise on both.


First, you're lacking top end. 40x11 @ 110 rpm on 700x44's = 33mph. So I'm spinning out early on gravel and really early on road. This is a huge dealbreaker to me.


Second 40x42 is 26.5 gear inches on the same tires. This is actually a lower low end than I usually run for gravel but a pretty high gear on a number of the hills on my local singletrack (hey, you claimed singletrack also). Especially when they are covered in pine needles and you need to apply the power smoothly, anything short of a fatbike tire will spin the tires loose with this gearing since you'll be mashing. My current gearing for offroad is about 20 inches on the low end.


Sorry, I've ridden 1x a bit and spent a lot of time on rides with other guys who have it. There isn't a single ride where the 1x riders aren't either spinning out on the downhills or running out of gearing on uphills. I mean, if you're comparing 1x to 2x7 or something then sure, 1x can cover the same range with similar steps, but a 2x with the same number of cogs in the cassette will always have better options than a 1x.
Hmmm is offline  
Old 07-03-19, 06:06 AM
  #23  
Koyote
Senior Member
 
Join Date: Sep 2017
Posts: 7,767
Mentioned: 37 Post(s)
Tagged: 0 Thread(s)
Quoted: 6882 Post(s)
Liked 10,873 Times in 4,637 Posts
Originally Posted by DrIsotope
As a guy with 15k+ miles with a 1X drivetrain, the armchair pontification about spinning out, not enough gearing range, etc... is hilarious.
As a guy who routinely has his ass handed to him by riders on single-speed bikes, I do agree with this. But it is also somewhat dependent on the rider and terrain -- some people can spin and mash better than others.
Koyote is offline  
Old 07-03-19, 06:20 AM
  #24  
Caliper
Senior Member
 
Join Date: May 2014
Location: Michigan
Posts: 990

Bikes: Many

Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 385 Post(s)
Liked 58 Times in 43 Posts
Originally Posted by Hmmm
Don't worry, I'll wait for you at the bottom of the hill.
Caliper is offline  
Old 07-04-19, 12:20 AM
  #25  
HTupolev
Senior Member
 
Join Date: Apr 2015
Location: Seattle
Posts: 4,261
Mentioned: 41 Post(s)
Tagged: 0 Thread(s)
Quoted: 1971 Post(s)
Liked 1,297 Times in 629 Posts
Originally Posted by DrIsotope
Having walked up my fair share of dirt hills I found too steep to pedal up, no amount of gearing could have prevented it. I'm not on a mountain bike. At some point, frame geometry and the limitations of the tires become an issue, usually long before the gearing does.
3.5mph, though? I drop into that range all the time without severe problems with tires or geometry, even though my gravel bike runs slicks and uses an aggressive road posture and has absurdly long chainstays (475mm) that make it hard to control rear wheel weighting. And if that's happening to me in a 24-28, and I'm often feeling mildly bottomed out when it's happening, and knowing that there are people who climb much slower than me (on the same gradients, so the tire and geometry issues are no different)... I'm not seeing how 24-42 is necessarily a ridiculous combination.

I've never met a paved incline I couldn't manage with a 1 : 1 final.
What does "manage" mean? I basically never have to get off and walk, but I don't consider gearing to be very adequate if it's costing me loads of performance and fatigue on prolonged climbing efforts.
HTupolev is offline  

Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.