Go Back  Bike Forums > Bike Forums > Mountain Biking
Reload this Page >

100mm fork on a bike that came with a 80mm

Notices
Mountain Biking Mountain biking is one of the fastest growing sports in the world. Check out this forum to discuss the latest tips, tricks, gear and equipment in the world of mountain biking.

100mm fork on a bike that came with a 80mm

Old 06-20-02, 07:19 PM
  #1  
gabiker
Senior Member
Thread Starter
 
gabiker's Avatar
 
Join Date: Mar 2002
Location: Rome, GA
Posts: 538

Bikes: Lemond Zurich, Specialized Stump Jumper, Soon to be Litespeed Solano

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
100mm fork on a bike that came with a 80mm

I have read some articles that say you shouldn't put a 100mm fork on a bike that came with a 80mm fork. What are everyones thoughts on this? Also if people have actually done it what was the results?

Thanks for any advice you can give.

By the way it is a 21" frame.
gabiker is offline  
Old 06-20-02, 08:02 PM
  #2  
MTBJeeper
Newbie
 
Join Date: Jun 2002
Location: Chicago 'burbs
Posts: 5
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
A longer fork will change the geometry of the bike by slackening the angle of the headtube back farther than the original fork. On an xc bike, the steering may be more sluggish than before. changing from, 80mm to 100mm may not be too noticeable on some frames, but a fork longer than 100mm will defintely have an effect on handling.
MTBJeeper is offline  
Old 06-20-02, 09:17 PM
  #3  
dirtbikedude
Gravity Is Yer Friend
 
dirtbikedude's Avatar
 
Join Date: May 2002
Location: "Over the Hill" and going down fast in the 805.
Posts: 2,961

Bikes: Scott Gambler, Scott Ransom, Kona Bear, Bianchi 928 Carbon/Chorus, C'Dale Rize4

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
As mentioned above it will slow down the steering of your bike. You might want to take a few easy rides to get a feel for it. I changed out my original fork that had 100mm travel for one with 180mm. There was a drastic change in the way the bike handled, for the better. Since I use the bike for dh, it made it less twitchy at speed.
CHEERS
dirtbikedude is offline  
Old 06-21-02, 06:28 PM
  #4  
urbanking
Life's Too Short
 
urbanking's Avatar
 
Join Date: Mar 2002
Location: Sudbury, Ontario
Posts: 266
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Play around with it abit, and mayeb even adjust the bars a bit until you get maximum performance, but it should work, and teh biek shouldn't loose too much strength. If the actual length of the forks are the same, they should work fine.
urbanking is offline  
Old 06-22-02, 09:46 AM
  #5  
bac
Senior Member
 
bac's Avatar
 
Join Date: Jun 2002
Location: Pennsylvania
Posts: 7,481

Bikes: Too many to list!

Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 3 Times in 3 Posts
Originally posted by gabiker
I have read some articles that say you shouldn't put a 100mm fork on a bike that came with a 80mm fork. What are everyones thoughts on this? Also if people have actually done it what was the results?

Thanks for any advice you can give.

By the way it is a 21" frame.
Like others have stated, it will change the head angle geometry a bit, but you very well may like the change. It should help with a smoother downhill experience, but it will slow down the steering a bit on the technical uphills. However, the difference isn't going to be terribly noticable.

Have fun with it, and let the group know how you rate the change!
bac is offline  
Old 06-22-02, 01:19 PM
  #6  
gabiker
Senior Member
Thread Starter
 
gabiker's Avatar
 
Join Date: Mar 2002
Location: Rome, GA
Posts: 538

Bikes: Lemond Zurich, Specialized Stump Jumper, Soon to be Litespeed Solano

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Thanks for all the feedback. From what I have heard here and a few other places I am going to try it. If it will improve downhill I am all for it and it sounds like it won't make that big of difference steering.

I will keep you posted.

Thanks again.
gabiker is offline  
Old 06-23-02, 05:44 AM
  #7  
threadend
Career Cyclist
 
threadend's Avatar
 
Join Date: Feb 2002
Location: Michigan, USA
Posts: 551
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
What they all said plus...doing this made my front tire seem lighter which took some adjustment on climbs. I ended up changing where I centered myself over the bike to keep the rear tire hooked up and keep the front end down. Overall, the results where favorable IMO.
__________________
2003 Iceman Challenge - 2:34:55 - 897 / 2,000*
2002 Iceman Challenge - 2:39:23 - 1093 / 2,186
2000 Iceman Challenge - 2:49:18 - 1516 / 2,153
*estimated
threadend is offline  
Old 06-23-02, 07:32 AM
  #8  
toolfreak
Ich bin ein Lowlander!
 
toolfreak's Avatar
 
Join Date: Mar 2001
Location: Atlantic Ocean, France
Posts: 583
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
I`ve changed lately from 70 mm to 115 mm, and the handling was what i expected; BETTER

With my old shock the riders weight was pretty much on the front, the handling on downhills was terrible.

The geometry changed with the new shock, and the weight is more on the back now, wich improves handling on high speed decents.

And yes, the climbing skills are worse than before, but i can take that

I think you will notice some difference, but not so radical as you thought.
__________________
Mark







Dancevalley 2th of august 2003 -> JXL, Laidback luke, Sasha, John Digweed, Monica Krusse.....and on!
toolfreak is offline  
Old 06-23-02, 07:35 AM
  #9  
urbanking
Life's Too Short
 
urbanking's Avatar
 
Join Date: Mar 2002
Location: Sudbury, Ontario
Posts: 266
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Wow, thats a big change toolfreak, is the changed geometry not going to weaken the bike in the long run? Thats my biggest concern.
urbanking is offline  
Old 06-23-02, 07:42 AM
  #10  
toolfreak
Ich bin ein Lowlander!
 
toolfreak's Avatar
 
Join Date: Mar 2001
Location: Atlantic Ocean, France
Posts: 583
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Urbanking, in what way do you think it will weaken the bike?

Just curious,
__________________
Mark







Dancevalley 2th of august 2003 -> JXL, Laidback luke, Sasha, John Digweed, Monica Krusse.....and on!
toolfreak is offline  
Old 06-23-02, 08:12 AM
  #11  
gabiker
Senior Member
Thread Starter
 
gabiker's Avatar
 
Join Date: Mar 2002
Location: Rome, GA
Posts: 538

Bikes: Lemond Zurich, Specialized Stump Jumper, Soon to be Litespeed Solano

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Threadend,

Did you go from an 80 to 100? Also what size frame are you on?

Thanks...
gabiker is offline  
Old 06-23-02, 09:02 AM
  #12  
threadend
Career Cyclist
 
threadend's Avatar
 
Join Date: Feb 2002
Location: Michigan, USA
Posts: 551
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Swapped an entry level Rockshox Indy? w/ 80 mm travel for an upgrade to Judy XC w/100 mm travel. There wasn't a big difference in weight between the two, if memory serves me (which isn't a garrantee of accuracy) I think the Judy XC is actually a bit heavier than the Indy was.

The frame is a 19.5" Giant Sedonna SE
__________________
2003 Iceman Challenge - 2:34:55 - 897 / 2,000*
2002 Iceman Challenge - 2:39:23 - 1093 / 2,186
2000 Iceman Challenge - 2:49:18 - 1516 / 2,153
*estimated
threadend is offline  
Old 06-23-02, 05:18 PM
  #13  
gabiker
Senior Member
Thread Starter
 
gabiker's Avatar
 
Join Date: Mar 2002
Location: Rome, GA
Posts: 538

Bikes: Lemond Zurich, Specialized Stump Jumper, Soon to be Litespeed Solano

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
I am going from a Judy TT to a Duke C and if I am not mistaking I can change the Duke to a 80 if I have to. I really think the 100 will be fine though. It should be a tremendous difference in the ride as well.
gabiker is offline  
Old 06-25-02, 10:34 AM
  #14  
stumpjumper
Lagomorph Demonicus
 
stumpjumper's Avatar
 
Join Date: Sep 2001
Location: Dayton, Ohio, USA
Posts: 795
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 2 Post(s)
Likes: 0
Liked 2 Times in 2 Posts
Went from an 80mm Manitou on my 20 inch Specialized frame to a 100mm Marizocci's. Yes, the front end is a bit lighter and requires a change in style, but all in all, I like it much better.
stumpjumper is offline  
Old 06-26-02, 04:05 PM
  #15  
Friggertool
Junior Member
 
Join Date: Jun 2002
Location: Newcastle, England
Posts: 8
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
I was going to change the 65mm rockshox that came on my Specialised hardrock to an 80mm Marzocchi fork (MXC air) . I checked the FAQs on Speccy's website and they said it would be OK. However, when the forks arrived they'd sent the 100mm version with ECC, which was nice of them. This meant a change from 65 to 100mm. The bike rides just fine. I must have done about 1000 miles since the switch and have not had any issues regarding steering or head angle.
Friggertool is offline  
Old 07-01-02, 06:53 PM
  #16  
gabiker
Senior Member
Thread Starter
 
gabiker's Avatar
 
Join Date: Mar 2002
Location: Rome, GA
Posts: 538

Bikes: Lemond Zurich, Specialized Stump Jumper, Soon to be Litespeed Solano

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Well I had my first ride tonight with the 100mm shock and I must say I am more than pleased. The only thing I noticed in the geometry was the front was a little higher, but there is no problem stearing or anything else. As far as going down hill and a smooth ride it is a 1000 times better than what I had.

The only unfortunate thing was I really didn't have the oportunity to do a real good downhill but when I do I am going to love it.

Thanks for all of your advice. It was well worth the investment and to make it even better I already sold my old shock so this one only cost me $90. WooHoo...
gabiker is offline  
Old 07-01-02, 07:06 PM
  #17  
WorldIRC
Canadian eh?
 
Join Date: May 2002
Location: Toronto
Posts: 2,135

Bikes: 2020 Specialized Roubaix Expert

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 131 Post(s)
Liked 96 Times in 54 Posts
glad your happy with it..
WorldIRC is offline  
Old 07-02-02, 03:28 AM
  #18  
Mashimaro
Senior Member
 
Join Date: Jun 2002
Location: Vancouver
Posts: 104
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
I decided to put a 4" travel fork on my bike as well. I used to run a first gen ('98) SID w/ almost 2.5" of travel. I liked how light it was but decided to change it to a SID 100. I found that my steering slowed down a bit, but overall, it wasn't that big of a change (probably cuz it sags 1" when i'm on it, and the older SID was made for XC racing w/ minimal sag). I like the way it feels now, but i doubt i'll go to 5".

And for the guy that was wondering why it would weaken your frame: i believe longer travel single crown (and double crowns) put far more stress at the head tube/down tube junction than a shorter travel fork.
Mashimaro is offline  
Old 07-02-02, 04:29 AM
  #19  
gabiker
Senior Member
Thread Starter
 
gabiker's Avatar
 
Join Date: Mar 2002
Location: Rome, GA
Posts: 538

Bikes: Lemond Zurich, Specialized Stump Jumper, Soon to be Litespeed Solano

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
I agree I wouldn't put a 5" on, but I am happy with the plush ride of the 4". I also went from a very low end fork to a pretty good one so that made a huge difference also.
gabiker is offline  
Old 07-05-02, 06:33 PM
  #20  
bike_man_15
Member
 
Join Date: Jun 2002
Posts: 47
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
i just went from 80 to 125 and i love it the steering is a little slower, but i like more that way, if i was you i would not worry about it
bike_man_15 is offline  
Old 07-09-02, 02:05 AM
  #21  
Mancini
Newbie
 
Join Date: Jul 2002
Location: Vancouver
Posts: 2
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Hi, this is my first time here (referred from an automotive board), so sorry in advance if there is a better forum in which to post this question. I just got back into mountain biking and my girlfriend is buying a Kona Cinder Cone or Caldera tomorrow. Can't wait.

I have a question about installing a suspension fork. I have a 1995 Stumpjumper M2 with an OLD Rock Shox Mag 21 that was installed by a bike shop way back when. I just got a great deal on a new 2001 Judy XC w/80mm (3 inches) of travel.

Question: I have to cut the steerer tube. How much do I cut? I could copy my other fork, but I'm not sure if the shop did it right in the first place. I could copy the rigid fork that came with the bike, but do I have to compensate for a certain amount of sag? Any help pointing me in the right direction would be greatly appreciated. Thank you.
Mancini is offline  
Old 07-09-02, 03:25 AM
  #22  
Mashimaro
Senior Member
 
Join Date: Jun 2002
Location: Vancouver
Posts: 104
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Welcome to bike forums buddy!

As for your question,
you'll have to take off the old headset lower race, and then install the new fork for bit to see how much you'll have to cut off. place on the stem (don't tighten anything) and then make sure you have some headset spacers. Once you have the spacers and the stem on..you should cut a little below the stem (approx 3mm.) that way, you can actually tighten the top cap down. You'll need a new cable, housing, starfangled nut when you install the new fork. It's not too hard...the only thing is make sure you don't damage the lower race when you take it off the old fork. you'll need a rubber mallet to help you out. When installing the new starfangled nut (AFTER you cut the steerer tube), screw the top cap flush w/ the nut and hammer it in almost 1cm. The rest is pretty simple. Hope it makes sense, good luck.

PS. you came from Revscene rite? welcome to a better forum.
Mashimaro is offline  
Old 07-09-02, 12:07 PM
  #23  
akmtnbiker
Junior Member
 
Join Date: Jun 2002
Posts: 10
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
My bike came with a 80mm fork and I was concerned about the geometry too. But my headangle being at 72.5 allowed for more travel and I went with a Manitou X-Vert with 105mm of travel and found that as my sweetspot. Feels much better than the 80mm and my steering hasn't changed noticably.

akmtnbiker
akmtnbiker is offline  
Old 07-09-02, 06:58 PM
  #24  
Cdude
Senior Member
 
Join Date: Jul 2002
Posts: 113
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Alls I can say is just take the bike to the shop and have them install the fork.

Installing a fork on your own is not worth it.
Cdude is offline  
Old 07-09-02, 07:15 PM
  #25  
gabiker
Senior Member
Thread Starter
 
gabiker's Avatar
 
Join Date: Mar 2002
Location: Rome, GA
Posts: 538

Bikes: Lemond Zurich, Specialized Stump Jumper, Soon to be Litespeed Solano

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
That is what I did and it only cost $15. I don't think it is worth getting my hands dirty for $15.
gabiker is offline  

Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.