I got a professional bike fit today
#1
Senior Member
Thread Starter
I got a professional bike fit today
After many people badgered me about how important it was to get a professional bike fit, I finally pulled the trigger and got fitted this morning. Now, I have to say, I've always been the odd duck. I like or am comfortable in positions many aren't comfortable. I say that to preface my valuation of a professional fit. As is always the case, YMMV.
I left the shop feeling quite underwhelmed. The basic conclusion is what I already strongly suspected, that being my crank arms are far too long. Once those are adjusted, most of my original measurements, with only some modest tweaks, are pretty much where they're supposed to be. I had already had planned, even requesting quotes, for shorter arms. It just so happened that the fit was scheduled before I got the shorter crank arms.
Once again, YMMV and if you don't feel at all comfortable on your bike, or maybe it's something that's included with a new purchase, then by all means take advantage of the service. As for me, I'm left with this feeling that I could have just spent that money on getting the shorter cranks like I was already planning and then tinkering with it because I was already pretty darn close.
I left the shop feeling quite underwhelmed. The basic conclusion is what I already strongly suspected, that being my crank arms are far too long. Once those are adjusted, most of my original measurements, with only some modest tweaks, are pretty much where they're supposed to be. I had already had planned, even requesting quotes, for shorter arms. It just so happened that the fit was scheduled before I got the shorter crank arms.
Once again, YMMV and if you don't feel at all comfortable on your bike, or maybe it's something that's included with a new purchase, then by all means take advantage of the service. As for me, I'm left with this feeling that I could have just spent that money on getting the shorter cranks like I was already planning and then tinkering with it because I was already pretty darn close.
Likes For VegasJen:
#2
Senior Member
Join Date: Oct 2008
Location: Portland, OR
Posts: 3,843
Bikes: Trek Domane SL6 Gen 3, Soma Fog Cutter, Focus Mares AL, Detroit Bikes Sparrow FG, Volae Team, Nimbus MUni
Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 896 Post(s)
Liked 2,065 Times
in
1,081 Posts
My experience was similar in that the adjustments were mostly small tweaks. The biggest change was lowering my saddle, which was done in stages to find the height that eliminated back pain.
I guess shortening crank arms is like lowering the saddle at the bottom of the stroke and raising the saddle at the top. Interesting.
The small tweaks made a significant comfort difference on long rides. I would not have come up with that specific set of of small changes on my own.
I guess shortening crank arms is like lowering the saddle at the bottom of the stroke and raising the saddle at the top. Interesting.
The small tweaks made a significant comfort difference on long rides. I would not have come up with that specific set of of small changes on my own.
#3
Method to My Madness
Join Date: Nov 2020
Location: Orange County, California
Posts: 3,663
Bikes: Trek FX 2, Cannondale Synapse, Cannondale CAAD4, Santa Cruz Stigmata GRX
Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 1948 Post(s)
Liked 1,471 Times
in
1,020 Posts
After many people badgered me about how important it was to get a professional bike fit, I finally pulled the trigger and got fitted this morning. Now, I have to say, I've always been the odd duck. I like or am comfortable in positions many aren't comfortable. I say that to preface my valuation of a professional fit. As is always the case, YMMV.
I left the shop feeling quite underwhelmed. The basic conclusion is what I already strongly suspected, that being my crank arms are far too long. Once those are adjusted, most of my original measurements, with only some modest tweaks, are pretty much where they're supposed to be. I had already had planned, even requesting quotes, for shorter arms. It just so happened that the fit was scheduled before I got the shorter crank arms.
Once again, YMMV and if you don't feel at all comfortable on your bike, or maybe it's something that's included with a new purchase, then by all means take advantage of the service. As for me, I'm left with this feeling that I could have just spent that money on getting the shorter cranks like I was already planning and then tinkering with it because I was already pretty darn close.
I left the shop feeling quite underwhelmed. The basic conclusion is what I already strongly suspected, that being my crank arms are far too long. Once those are adjusted, most of my original measurements, with only some modest tweaks, are pretty much where they're supposed to be. I had already had planned, even requesting quotes, for shorter arms. It just so happened that the fit was scheduled before I got the shorter crank arms.
Once again, YMMV and if you don't feel at all comfortable on your bike, or maybe it's something that's included with a new purchase, then by all means take advantage of the service. As for me, I'm left with this feeling that I could have just spent that money on getting the shorter cranks like I was already planning and then tinkering with it because I was already pretty darn close.
Don't feel underwhelmed just because your fitter only made "modest tweaks"; those tweaks may represent optimizations that you only realize later after you have become more used to your new settings. Even if your new settings are not better than your old, the bike fit may still be worth it for someone knowledgeable to confirm that your prior settings were "already pretty darn close," especially since you are an "odd duck." Given your riding history, it would be more unexpected for the fitter to have made drastic changes to every touch point.
Likes For SoSmellyAir:
#4
Senior Member
I've never tried a pro fit, but have viewed numerous videos on bike fit. Some helped, most did not. I found tweaking everything after the first several rides from saddle height/lateral position, handle bar stems, handlebar position, so on. It's a long process but I get a good fit in the end,
And unfortunately, I had to change out some parts, but in the end it worked out and now have a fine collection of stems, saddles, seat posts, handlebars.
And unfortunately, I had to change out some parts, but in the end it worked out and now have a fine collection of stems, saddles, seat posts, handlebars.
Likes For MarcusT:
#7
Senior Member
Join Date: Jan 2005
Location: Baltimore, MD
Posts: 5,375
Mentioned: 15 Post(s)
Tagged: 0 Thread(s)
Quoted: 2484 Post(s)
Liked 2,956 Times
in
1,679 Posts
"Doctor, you're charging me that much for what? Just to tell me I'm healthy? For that kind of money, I demand that you operate. Take something out or put something in."
Just pointing out that having a pro confirm that you've done a good job at setting up your bike isn't a bad thing.
Just pointing out that having a pro confirm that you've done a good job at setting up your bike isn't a bad thing.
Last edited by Trakhak; 03-28-24 at 02:01 AM.
Likes For Trakhak:
#8
Senior Member
Join Date: Oct 2016
Posts: 728
Mentioned: 6 Post(s)
Tagged: 0 Thread(s)
Quoted: 365 Post(s)
Liked 419 Times
in
248 Posts
If someone has been more than an occasional, casual cyclist for a while (as you have), I suspect that one would have been motivated to get the various touch points "pretty darn close"; otherwise, one would be noticeably uncomfortable, especially over longer distances or at greater intensity.
(Note: I don't think they were just trying to get me out of there, because this is my LBS and I've been with them for more than 20 years. I've purchased several bikes, brought my many bikes in for various issues, bought consumables and clothes, accessories (lights, computers, etc.) and so on. I know the fitter who fitted me on my new bike, we've had many conversations about bikes and cycling, and we had a lot of discussions during the purchase of my latest bike.)
Likes For noimagination:
#9
Senior Member
Join Date: May 2021
Posts: 8,450
Mentioned: 12 Post(s)
Tagged: 0 Thread(s)
Quoted: 4415 Post(s)
Liked 4,867 Times
in
3,012 Posts
A professional bike fit is only important if you can’t figure it out for yourself or if you have specific problems that you have failed to resolve. It seems like you had already figured it out.
If you went to see 10 different bike fitters, you would also get 10 different fits to choose from and they might all have pros and cons. It’s really not an exact science.
I’m a DIY fitter myself, but being an engineer I’m quite analytical. There are also some great online resources. MyVeloFit is very good if you are tech savvy and this pro fitter offers a really comprehensive DIY guide for just a few dollars.
https://bikedynamics.co.uk/shop.htm
Likes For PeteHski:
#10
Senior Member
Join Date: Jan 2010
Posts: 39,249
Mentioned: 211 Post(s)
Tagged: 1 Thread(s)
Quoted: 18420 Post(s)
Liked 15,568 Times
in
7,334 Posts
Likes For indyfabz:
#11
Full Member
Join Date: Mar 2022
Location: SW WI
Posts: 219
Bikes: Cannondale Topstone, Trek Dual Sport, State Bicycle Klunker
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 87 Post(s)
Liked 132 Times
in
69 Posts
Pretty sure it makes a difference, but not sure if it would be noticeable by most. Tons of videos out there to get you close, then it time, trial & error, and throwing $ at parts to get you closer. Probably the biggest advantage I see is it could save you some cash in parts swapping and time…….
again I’ve never experienced a fitting, but I wouldn’t think it would be a huge difference. Once you get the initial bike size right, seat right(height, angle, for and aft) most everything else makes minimal difference to me.
again I’ve never experienced a fitting, but I wouldn’t think it would be a huge difference. Once you get the initial bike size right, seat right(height, angle, for and aft) most everything else makes minimal difference to me.
#12
Senior Member
Join Date: Oct 2008
Location: Right where I'm supposed to be
Posts: 1,634
Bikes: Franklin Frames Custom, Rivendell Bombadil
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 117 Post(s)
Liked 209 Times
in
127 Posts
The inherent issue with a "fitting" is that every fitter has their own ideas of what a proper fit is. It's not like there is a Universally-applicale-to-all formula, which is implied in every "you should see a bike fitter". Which one, based on what theories ? While shorter crank arms for Jen was obvious to many, that's only one small aspect of fitting oneself, of finding the path of "least resistance" in propelling yourself forward on a bicycle. From my experience, the inherent intuition within us all, that "still small voice", knows everything one could possibly ever need to know. IT's the only Trust worthy of the word Trust. Nobody knows One better than the Inherent Trust of which One Exists As
.
![Love](images/smilies/1luvu.gif)
Likes For Garthr:
#13
Senior Member
Obviously, the fit calculations are based on studies and averages, but I wonder if age is factored in. I am not nearly as flexible now as I was 50 years ago and riding on the drops is more uncomfortable every year.
That said, after buying my new bike a few years ago, I rode with an allen wrench for a while and did some minor tweaks. I think that there is an acceptable range of "fit" and not one precise measurement or location.
That said, after buying my new bike a few years ago, I rode with an allen wrench for a while and did some minor tweaks. I think that there is an acceptable range of "fit" and not one precise measurement or location.
Likes For bblair:
#14
Senior Member
Join Date: Sep 2017
Posts: 7,887
Mentioned: 38 Post(s)
Tagged: 0 Thread(s)
Quoted: 6972 Post(s)
Liked 10,968 Times
in
4,692 Posts
What did the bike fitter think about your seatpost? I'm genuinely curious.
![](https://cimg8.ibsrv.net/gimg/www.corvetteforum.com-vbulletin/800x592/80-block8_c5b7d389ddeb0f7264350c6fd3c11bba61e90608.jpg)
Likes For Koyote:
#15
Full Member
Join Date: Mar 2022
Location: SW WI
Posts: 219
Bikes: Cannondale Topstone, Trek Dual Sport, State Bicycle Klunker
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 87 Post(s)
Liked 132 Times
in
69 Posts
The inherent issue with a "fitting" is that every fitter has their own ideas of what a proper fit is. It's not like there is a Universally-applicale-to-all formula, which is implied in every "you should see a bike fitter". Which one, based on what theories ? While shorter crank arms for Jen was obvious to many, that's only one small aspect of fitting oneself, of finding the path of "least resistance" in propelling yourself forward on a bicycle. From my experience, the inherent intuition within us all, that "still small voice", knows everything one could possibly ever need to know. IT's the only Trust worthy of the word Trust. Nobody knows One better than the Inherent Trust of which One Exists As
.
![Love](images/smilies/1luvu.gif)
![](https://cimg7.ibsrv.net/gimg/bikeforums.net-vbulletin/346x527/img_0419_3abc2845249234e505b7fe264875290a19025814.png)
#16
Senior Member
Join Date: May 2021
Posts: 8,450
Mentioned: 12 Post(s)
Tagged: 0 Thread(s)
Quoted: 4415 Post(s)
Liked 4,867 Times
in
3,012 Posts
Obviously, the fit calculations are based on studies and averages, but I wonder if age is factored in. I am not nearly as flexible now as I was 50 years ago and riding on the drops is more uncomfortable every year.
That said, after buying my new bike a few years ago, I rode with an allen wrench for a while and did some minor tweaks. I think that there is an acceptable range of "fit" and not one precise measurement or location.
That said, after buying my new bike a few years ago, I rode with an allen wrench for a while and did some minor tweaks. I think that there is an acceptable range of "fit" and not one precise measurement or location.
I agree about providing an acceptable range of fit. That’s how MyVeloFit and most other methods work. They give you a range defined by min and max values for parameters like saddle height and joint angles.
#17
Senior Member
Join Date: Aug 2009
Posts: 1,814
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 501 Post(s)
Liked 631 Times
in
373 Posts
Obviously, the fit calculations are based on studies and averages, but I wonder if age is factored in. I am not nearly as flexible now as I was 50 years ago and riding on the drops is more uncomfortable every year.
That said, after buying my new bike a few years ago, I rode with an allen wrench for a while and did some minor tweaks. I think that there is an acceptable range of "fit" and not one precise measurement or location.
That said, after buying my new bike a few years ago, I rode with an allen wrench for a while and did some minor tweaks. I think that there is an acceptable range of "fit" and not one precise measurement or location.
#18
Senior Member
I felt the same way when I got fitted. Never again and that’s with one pro fit and 2 others from different bike shops.
__________________
George
George
#19
Senior Member
Join Date: Dec 2010
Location: northern Deep South
Posts: 8,904
Bikes: Fuji Touring, Novara Randonee
Mentioned: 36 Post(s)
Tagged: 0 Thread(s)
Quoted: 2604 Post(s)
Liked 1,933 Times
in
1,213 Posts
VegasJen I'd take that as a confirmation that you're intelligent enough and willing to consider enough variations that you've already done everything a pro fitter can do.
Except the cranks, which you'd figured out but hadn't implemented.
Now cut back on the analysis and kibbitzing, get back out there and enjoy riding the bike!
Except the cranks, which you'd figured out but hadn't implemented.
Now cut back on the analysis and kibbitzing, get back out there and enjoy riding the bike!
![Big Grin](images/smilies/biggrin.gif)
#20
I'm good to go!
Join Date: Jul 2017
Location: Mississippi
Posts: 14,992
Bikes: Tarmac Disc Comp Di2 - 2020
Mentioned: 51 Post(s)
Tagged: 0 Thread(s)
Quoted: 6196 Post(s)
Liked 4,810 Times
in
3,318 Posts
I've always fit myself to my bikes and apparently it works well enough. However I'm not against going to a fitter just to see if there is anything they suggest that might help. Particularly if one is having issues they can't figure out. Some cyclist are just poor at realizing what's the real cause of the body issues they are having and what if anything on the bike is causing that.
Of course that's going to cost big bucks. But it's useful knowledge even if all they do is confirm you are doing it right already. Though I do have to say that I don't agree with the way some fitters go about fitting. But that's another story much like all the different diet fads.
Of course that's going to cost big bucks. But it's useful knowledge even if all they do is confirm you are doing it right already. Though I do have to say that I don't agree with the way some fitters go about fitting. But that's another story much like all the different diet fads.
Likes For prj71:
#22
Senior Member
Join Date: Feb 2015
Location: Mission Viejo
Posts: 5,806
Bikes: 1986 Cannondale SR400 (Flat bar commuter), 1988 Cannondale Criterium XTR, 1992 Serotta T-Max, 1995 Trek 970
Mentioned: 20 Post(s)
Tagged: 0 Thread(s)
Quoted: 1944 Post(s)
Liked 2,164 Times
in
1,323 Posts
I think bikes are designed to fit into a range for the majority of riders so a fit on an existing bike will always be some amount of tweaking. You already have the bike, the geometry isn’t changing.
Ideally there is a goal of getting a good balance of weight that also puts the rider in a comfortable riding position. Anyone who has ridden a crank forward bike can quickly understand the effects of poor weight distribution. The rider to bike weight ratio is so significant that where it is located impacts how a bike reacts.
The curveball is when a rider experiences pain, or has physical limitations, especially with age. I’m not a fitter, but making on the fly adjustments while on a ride should be part of it. Teaching someone the how and why, even if is not absolute, will be valuable an hour or two into a ride. Obviously swapping a crank mid-century is not a viable option.
John
Ideally there is a goal of getting a good balance of weight that also puts the rider in a comfortable riding position. Anyone who has ridden a crank forward bike can quickly understand the effects of poor weight distribution. The rider to bike weight ratio is so significant that where it is located impacts how a bike reacts.
The curveball is when a rider experiences pain, or has physical limitations, especially with age. I’m not a fitter, but making on the fly adjustments while on a ride should be part of it. Teaching someone the how and why, even if is not absolute, will be valuable an hour or two into a ride. Obviously swapping a crank mid-century is not a viable option.
John
#23
Clark W. Griswold
Join Date: Mar 2014
Location: ,location, location
Posts: 13,525
Bikes: Foundry Chilkoot Ti W/Ultegra Di2, Salsa Timberjack Ti, Cinelli Mash Work RandoCross Fun Time Machine, 1x9 XT Parts Hybrid, Co-Motion Cascadia, Specialized Langster, Phil Wood Apple VeloXS Frame (w/DA 7400), R+M Supercharger2 Rohloff, Habanero Ti 26
Mentioned: 54 Post(s)
Tagged: 0 Thread(s)
Quoted: 4357 Post(s)
Liked 3,995 Times
in
2,666 Posts
What it seems nobody has mentioned or asked is what kind of fit you got VegasJen a static fit is generally pretty bad sort of like going to a Subway and saying subs are bad. A static fit could help some but a dynamic fit is going to be the way to go think something like Retül or similar. It also may not be huge tweaks either not everyone needs huge tweaks but having someone point out the tweaks maybe confirm things you had been thinking is not a bad thing. Not everything requires the massive adjustable wrench sometimes a 2.5 hex wrench is all that you need and it may seem more silly to pay money to get that but it can help. Plus most fitters will have a test ride period and then you come back to make additional adjustments as needed or follow up in some way.
Likes For veganbikes:
#24
Senior Member
Join Date: Jul 2006
Location: San Jose (Willow Glen) Ca
Posts: 9,847
Bikes: Kirk Custom JK Special, '84 Team Miyata,(dura ace old school) 80?? SR Semi-Pro 600 Arabesque
Mentioned: 106 Post(s)
Tagged: 0 Thread(s)
Quoted: 2338 Post(s)
Liked 2,827 Times
in
1,543 Posts
I would look at this a confirmation the basics are good, so elimination of wondering about that may have some value to the OP
It is also not a bad thing as I would not be surprised if a lot of people ride with a close fit, but not optimum fit......
I found out my seat height was too low when i had a custom frame built and leg length did not match seat height....raised 2 cm and made a huge difference
It is also not a bad thing as I would not be surprised if a lot of people ride with a close fit, but not optimum fit......
I found out my seat height was too low when i had a custom frame built and leg length did not match seat height....raised 2 cm and made a huge difference
__________________
Life is too short not to ride the best bike you have, as much as you can
(looking for Torpado Super light frame/fork or for Raleigh International frame fork 58cm)
Life is too short not to ride the best bike you have, as much as you can
(looking for Torpado Super light frame/fork or for Raleigh International frame fork 58cm)
#25
Senior Member
Join Date: Mar 2020
Location: Nevada County, California
Posts: 790
Bikes: Subject to change at any given moment but currently is...... Colnago Mapei, Colnago C40, Wilier Triestina Carbon, Wilier Triestina Ramato, Follis 472, Peugeot PX60, Razesa, Orbea Terra, Soma Pescadero and 1/2 owner of a Santana tandem.
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 336 Post(s)
Liked 782 Times
in
264 Posts
I suspect many of us achieved our “fit” by years of riding and then making adjustments as needed. Undoubtedly a much longer way of doing it but I’ve found a fit I wouldn’t alter no matter who gave contrary advice.
Shorter crank arms was my last major change after spending considerable time on aero bars, it felt like I was nearly kneeing myself in the chest every pedal stroke.
Shorter crank arms was my last major change after spending considerable time on aero bars, it felt like I was nearly kneeing myself in the chest every pedal stroke.
Likes For Tomm Willians: