Avid BB5 frustration
#1
Senior Member
Thread Starter
Join Date: Jul 2009
Posts: 1,753
Bikes: 1986 KHS Fiero, 1989 Trek 950, 1990 Trek 7000, 1991 Gary Fisher Hoo Koo E Koo, 1992 Trek 1400, 1997 Cannondale CAD2 R300, 1998 Cannondale CAD2 R200, 2002 Marin San Rafael, 2006 Cannondale CAAD8 R1000, 2010 Performance Access XCL9R
Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
Quoted: 284 Post(s)
Liked 385 Times
in
207 Posts
Avid BB5 frustration
Bike is a Performance Access XCL 9r, Sora 3500 9 speed brifters on Woodchipper bars. Pulling Shimano SLX RD, SRAM X5 FD. Brakes are Avid BB5 mechanical disc brakes 180mm front, 160 rear.
Last year the rear brake just didn't seem to grab tight anymore. Before that, I could lock it up on pavement and slide it. I put new pads in, cleaned the rotor of dirt and grease. I can get it to lock up, but it drags. If I loosen it up so it doesn't drag, it barely slows me down. Conversely, the front nearly throws me over the bars, I can lock it in dirt...
My frustration is at the point of feeling unsafe on gravel descents. I'm considering swapping in a 180mm rotor and proper adapter, and getting an Avid BB7 road specific caliper. Any ideas before dropping the bucks for new parts?
Last year the rear brake just didn't seem to grab tight anymore. Before that, I could lock it up on pavement and slide it. I put new pads in, cleaned the rotor of dirt and grease. I can get it to lock up, but it drags. If I loosen it up so it doesn't drag, it barely slows me down. Conversely, the front nearly throws me over the bars, I can lock it in dirt...
My frustration is at the point of feeling unsafe on gravel descents. I'm considering swapping in a 180mm rotor and proper adapter, and getting an Avid BB7 road specific caliper. Any ideas before dropping the bucks for new parts?
#2
Senior Member
Join Date: Feb 2018
Posts: 1,410
Bikes: 2017 Specialized Allez Sprint Comp
Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 850 Post(s)
Liked 344 Times
in
247 Posts
If you mean the “dead” pad, then I’m not sure what to say, really. Is the rubbing intermittent or continuous? If intermittent, try truing your rotor to get the dead pad closer?
Are you using compressionless brake cables? That would be a wise investment for mechanical discs. Also, if you do feel the need to go with a new brake (you shouldn’t, all of a sudden), a lot of people have praised the TRP Spyre as a good modern brake.
Fundamentally, though, if a brake is good enough for your front, it’s good enough for your rear.
Last edited by smashndash; 10-29-19 at 12:24 AM.
#3
Senior Member
Thread Starter
Join Date: Jul 2009
Posts: 1,753
Bikes: 1986 KHS Fiero, 1989 Trek 950, 1990 Trek 7000, 1991 Gary Fisher Hoo Koo E Koo, 1992 Trek 1400, 1997 Cannondale CAD2 R300, 1998 Cannondale CAD2 R200, 2002 Marin San Rafael, 2006 Cannondale CAAD8 R1000, 2010 Performance Access XCL9R
Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
Quoted: 284 Post(s)
Liked 385 Times
in
207 Posts
By “drag” do you mean the pads rub the rotor? If so, you could have a cable issue. Take the cable off and see if the brake arm still snaps back after engagement.
If you mean the “dead” pad, then I’m not sure what to say, really. Is the rubbing intermittent or continuous? If intermittent, try truing your rotor to get the dead pad closer?
Are you using compressionless brake cables? That would be a wise investment for mechanical discs. Also, if you do feel the need to go with a new brake (you shouldn’t, all of a sudden), a lot of people have praised the TRP Spyre as a good modern brake.
Fundamentally, though, if a brake is good enough for your front, it’s good enough for your rear.
If you mean the “dead” pad, then I’m not sure what to say, really. Is the rubbing intermittent or continuous? If intermittent, try truing your rotor to get the dead pad closer?
Are you using compressionless brake cables? That would be a wise investment for mechanical discs. Also, if you do feel the need to go with a new brake (you shouldn’t, all of a sudden), a lot of people have praised the TRP Spyre as a good modern brake.
Fundamentally, though, if a brake is good enough for your front, it’s good enough for your rear.
As I didn't assemble this bike in this configuration, I'm not sure if the brake cables are compression less housings are not. I hadn't even considered that.
I agree, good enough for the front should be good enough for the rear.
I will swap brake cables and see if this helps.
Thank you.
#5
Seńor Member
Join Date: Feb 2013
Posts: 5,066
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 649 Post(s)
Liked 292 Times
in
215 Posts
Are these road-compatible BB5s? If they are the MTB 'long pull' version they will be very difficult to get to work acceptably with 'short pull' brake levers. A mm lost in housing compression or to pad wear will throw everything off.
We discovered the same thing in the mid '90s when V brakes first came on the scene - if the stars align correctly you can get a scary powerful brake, but the odds were just as good that they would simultaneously rub and not provide braking power before the levers are squeezed to the bars.
We discovered the same thing in the mid '90s when V brakes first came on the scene - if the stars align correctly you can get a scary powerful brake, but the odds were just as good that they would simultaneously rub and not provide braking power before the levers are squeezed to the bars.
#6
Senior Member
Join Date: Mar 2007
Location: SF Bay Area, East bay
Posts: 7,658
Bikes: Miyata 618 GT, Marinoni, Kestral 200 2002 Trek 5200, KHS Flite, Koga Miyata, Schwinn Spitfire 5, Mondia Special, Univega Alpina, Miyata team Ti, Santa Cruz Highball
Mentioned: 53 Post(s)
Tagged: 0 Thread(s)
Quoted: 1609 Post(s)
Liked 2,590 Times
in
1,224 Posts
#7
Senior Member
Join Date: Feb 2018
Posts: 1,410
Bikes: 2017 Specialized Allez Sprint Comp
Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 850 Post(s)
Liked 344 Times
in
247 Posts
Yes, dragging the rotor. I have tried a number of different adjustments, pad seatings. The arm snaps back readily with the cable off. And the rotor seems quite true.
As I didn't assemble this bike in this configuration, I'm not sure if the brake cables are compression less housings are not. I hadn't even considered that.
I agree, good enough for the front should be good enough for the rear.
I will swap brake cables and see if this helps.
Thank you.
As I didn't assemble this bike in this configuration, I'm not sure if the brake cables are compression less housings are not. I hadn't even considered that.
I agree, good enough for the front should be good enough for the rear.
I will swap brake cables and see if this helps.
Thank you.
I suspect the real issue is just grit and gunk in the rear cable. The rear cable usually has an exposed part running across the frame, and thus has greater opportunity for contamination. It is also longer, so there’s more room for grit to exist.
#8
Senior Member
Join Date: Sep 2010
Location: Roswell, GA
Posts: 8,319
Bikes: '93 Trek 750, '92 Schwinn Crisscross, '93 Mongoose Alta
Mentioned: 30 Post(s)
Tagged: 0 Thread(s)
Quoted: 1438 Post(s)
Liked 1,092 Times
in
723 Posts
If it has worked in the past it should be able to be made to work again. I am betting that new cables (both inner and housing) will be a big improvement. Did you bed-in the new pads per the manufacturer's recommendations?
#9
Senior Member
Thread Starter
Join Date: Jul 2009
Posts: 1,753
Bikes: 1986 KHS Fiero, 1989 Trek 950, 1990 Trek 7000, 1991 Gary Fisher Hoo Koo E Koo, 1992 Trek 1400, 1997 Cannondale CAD2 R300, 1998 Cannondale CAD2 R200, 2002 Marin San Rafael, 2006 Cannondale CAAD8 R1000, 2010 Performance Access XCL9R
Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
Quoted: 284 Post(s)
Liked 385 Times
in
207 Posts
True enough they don't wobble and stop the wheel...
They may be old enough, they were only MTB, but I don't know. This bike was a gift 5 years ago...
I've done that. Most of it at least.
As the bike is a drop bar bike, it was built with cyclocross inline levers on the tops as well. From that point to the rear brake it is all in brake housing. No exposed inner cable till the bottom.
As I don't know what housing was used, and I don't know the history of the bike before me, I see some prudence in changing to a better compressionless set up. I have that on 2 of my roadbikes, and feel like both stop very well.
As it has worked fine in the past, it should now. As for bedding the pads, I don't think they did bed well as I couldn't stop as strong as I wanted. Which I originally thought was worn pads. I may order new pads again just to rule them out.
I have toyed with a front to rear swap to see if it is a caliper issue. But I will what new cables and pads offer first.
I don’t mean that the reason for the issue is that you don’t have compressionless housing. I just mentioned that because, if you are getting a new cable housing, it will help quite a bit.
I suspect the real issue is just grit and gunk in the rear cable. The rear cable usually has an exposed part running across the frame, and thus has greater opportunity for contamination. It is also longer, so there’s more room for grit to exist.
I suspect the real issue is just grit and gunk in the rear cable. The rear cable usually has an exposed part running across the frame, and thus has greater opportunity for contamination. It is also longer, so there’s more room for grit to exist.
As I don't know what housing was used, and I don't know the history of the bike before me, I see some prudence in changing to a better compressionless set up. I have that on 2 of my roadbikes, and feel like both stop very well.
I have toyed with a front to rear swap to see if it is a caliper issue. But I will what new cables and pads offer first.
#10
Senior Member
Thread Starter
Join Date: Jul 2009
Posts: 1,753
Bikes: 1986 KHS Fiero, 1989 Trek 950, 1990 Trek 7000, 1991 Gary Fisher Hoo Koo E Koo, 1992 Trek 1400, 1997 Cannondale CAD2 R300, 1998 Cannondale CAD2 R200, 2002 Marin San Rafael, 2006 Cannondale CAAD8 R1000, 2010 Performance Access XCL9R
Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
Quoted: 284 Post(s)
Liked 385 Times
in
207 Posts
Figure, Might as well show the bike...
#11
Senior Member
Join Date: Aug 2006
Posts: 1,895
Mentioned: 8 Post(s)
Tagged: 0 Thread(s)
Quoted: 184 Post(s)
Likes: 0
Liked 67 Times
in
53 Posts
You're using a mountain brake with a road lever.
Mountain BB5: https://www.sram.com/en/sram/models/db-blbg-5m-a1
Road BB5: https://www.sram.com/en/sram/models/db-blbg-5r-a1
Mountain BB5: https://www.sram.com/en/sram/models/db-blbg-5m-a1
Road BB5: https://www.sram.com/en/sram/models/db-blbg-5r-a1
#12
Senior Member
Join Date: Feb 2007
Posts: 1,437
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 624 Post(s)
Likes: 0
Liked 396 Times
in
274 Posts
If cobba is correct I would go with the BB7 road verson for replacement and put the Yokozuna Reaction Brake Cable System on it. All other compressionless housing is weak and will compress. Yokozuna is the only trually compressionless housing sold.
#13
Senior Member
Join Date: Aug 2006
Posts: 1,895
Mentioned: 8 Post(s)
Tagged: 0 Thread(s)
Quoted: 184 Post(s)
Likes: 0
Liked 67 Times
in
53 Posts
I'd get a pair and replace the front caliper too, even if the front brake seems to be working ok at the moment.
https://www.ebay.com/itm/2QTY-SRAM-B...W/333221201946
With the current setup, the levers are only pulling half as much cable as what's needed, as the pads wear down on the mountain calipers, you won't have as much pad adjustment as you would with a road caliper.
https://www.ebay.com/itm/2QTY-SRAM-B...W/333221201946
With the current setup, the levers are only pulling half as much cable as what's needed, as the pads wear down on the mountain calipers, you won't have as much pad adjustment as you would with a road caliper.
#14
Advanced Slacker
Join Date: Feb 2017
Posts: 6,210
Bikes: Soma Fog Cutter, Surly Wednesday, Canfielld Tilt
Mentioned: 26 Post(s)
Tagged: 0 Thread(s)
Quoted: 2762 Post(s)
Liked 2,537 Times
in
1,433 Posts
If it is the case that you have the MTB version of the BB5 on there, that would go a long way to explain why the brakes were super powerful when they work, but are extremely hard to set up not to drag.
The road levers pull less cable, so the caliper can’t move as far as it needs to.
replacing with road version should take care of that.
Also, as others have suggested, compression-less brake housing makes a big difference, especially on the rear.
The road levers pull less cable, so the caliper can’t move as far as it needs to.
replacing with road version should take care of that.
Also, as others have suggested, compression-less brake housing makes a big difference, especially on the rear.
#15
Advanced Slacker
Join Date: Feb 2017
Posts: 6,210
Bikes: Soma Fog Cutter, Surly Wednesday, Canfielld Tilt
Mentioned: 26 Post(s)
Tagged: 0 Thread(s)
Quoted: 2762 Post(s)
Liked 2,537 Times
in
1,433 Posts
You're using a mountain brake with a road lever.
Mountain BB5: https://www.sram.com/en/sram/models/db-blbg-5m-a1
Road BB5: https://www.sram.com/en/sram/models/db-blbg-5r-a1
Mountain BB5: https://www.sram.com/en/sram/models/db-blbg-5m-a1
Road BB5: https://www.sram.com/en/sram/models/db-blbg-5r-a1
#17
Senior Member
Thread Starter
Join Date: Jul 2009
Posts: 1,753
Bikes: 1986 KHS Fiero, 1989 Trek 950, 1990 Trek 7000, 1991 Gary Fisher Hoo Koo E Koo, 1992 Trek 1400, 1997 Cannondale CAD2 R300, 1998 Cannondale CAD2 R200, 2002 Marin San Rafael, 2006 Cannondale CAAD8 R1000, 2010 Performance Access XCL9R
Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
Quoted: 284 Post(s)
Liked 385 Times
in
207 Posts
Not knowing anything of disc brakes, how long has the BB 5 been offered in road and MTB? I know this bike was built with what my friend had on hand at the time...
#18
Advanced Slacker
Join Date: Feb 2017
Posts: 6,210
Bikes: Soma Fog Cutter, Surly Wednesday, Canfielld Tilt
Mentioned: 26 Post(s)
Tagged: 0 Thread(s)
Quoted: 2762 Post(s)
Liked 2,537 Times
in
1,433 Posts
K
How do you know that?
If you look under “specs” for the BB5 road it lists back as a color option (Gloss Black, Platinum, Silver). And here is one for sale:
https://www.rei.com/product/847061/a...sc-brake-160mm
In any event I assume there is a model number somewhere in the caliper.
If you look under “specs” for the BB5 road it lists back as a color option (Gloss Black, Platinum, Silver). And here is one for sale:
https://www.rei.com/product/847061/a...sc-brake-160mm
In any event I assume there is a model number somewhere in the caliper.
Last edited by Kapusta; 10-30-19 at 08:01 AM.
#19
Senior Member
Join Date: Aug 2006
Posts: 1,895
Mentioned: 8 Post(s)
Tagged: 0 Thread(s)
Quoted: 184 Post(s)
Likes: 0
Liked 67 Times
in
53 Posts
Just had a look at some old archived SRAM pages from a couple of years ago on the web archive, they only list Platinum as the color for Road BB5's, maybe those extra colors on the current page are something new.
#20
Senior Member
Join Date: Feb 2017
Location: Northern Shenandoah Valley
Posts: 4,141
Bikes: More bikes than riders
Mentioned: 36 Post(s)
Tagged: 0 Thread(s)
Quoted: 1446 Post(s)
Liked 762 Times
in
570 Posts
Nice bike, and nice scenery!
Your rear caliper looks to be adjusted at near its full cable travel. That's generally going to result in a pretty heavy brake, and doesn't really have any advantages (that I'm aware of). If you replace the cable and housing, I would adjust it so your caliper is mounted so the outboard pad (the one closest to the outside of the bike) is JUST BARELY clearing the brake rotor (no rub), and then thread the backer for the inboard pad (the one closest to the hub of the bike) in so that it, too, is JUST BARELY clearing the brake rotor (no rub). The activation arm should be all the way relaxed in this position, and the cable completely slack. At that point, you have the least amount of preload on the internal spring in the caliper, and your brake lever pull will be the lightest.
That is, of course, assuming that you have compatible pull ratios on the caliper and lever.
Your rear caliper looks to be adjusted at near its full cable travel. That's generally going to result in a pretty heavy brake, and doesn't really have any advantages (that I'm aware of). If you replace the cable and housing, I would adjust it so your caliper is mounted so the outboard pad (the one closest to the outside of the bike) is JUST BARELY clearing the brake rotor (no rub), and then thread the backer for the inboard pad (the one closest to the hub of the bike) in so that it, too, is JUST BARELY clearing the brake rotor (no rub). The activation arm should be all the way relaxed in this position, and the cable completely slack. At that point, you have the least amount of preload on the internal spring in the caliper, and your brake lever pull will be the lightest.
That is, of course, assuming that you have compatible pull ratios on the caliper and lever.
#21
Senior Member
Join Date: Aug 2006
Posts: 1,895
Mentioned: 8 Post(s)
Tagged: 0 Thread(s)
Quoted: 184 Post(s)
Likes: 0
Liked 67 Times
in
53 Posts
If you can, ask your friend if the brakes were the original ones that came on the bike when it had flat handlebars.
#22
Advanced Slacker
Join Date: Feb 2017
Posts: 6,210
Bikes: Soma Fog Cutter, Surly Wednesday, Canfielld Tilt
Mentioned: 26 Post(s)
Tagged: 0 Thread(s)
Quoted: 2762 Post(s)
Liked 2,537 Times
in
1,433 Posts
I’m with cobba in suspecting that you have a MTB version, but extra verification would help.
BB7s are a bit easier to get set up right... but even those take some practice. I’ve used BB7s for almost 18 years, and it took a while to get the art and science down for good setup.
Last edited by Kapusta; 10-30-19 at 09:58 AM.
#23
Senior Member
Join Date: Apr 2010
Location: Elevation 666m Edmonton Canada
Posts: 2,482
Bikes: 2013 Custom SA5w / Rohloff Tourster
Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
Quoted: 1237 Post(s)
Liked 321 Times
in
248 Posts
Yes throw that POS crap in the GARBAGE, I had them for too long also. Road<>MTB ?? WTF is the diff ??
Get a TRP Spyre caliper with both side moving pads. Keep using the softer resin pads that grip better and don't squeal. They don't seem to care what the gap is either, I like more so they can't rub.
I've had them on my tour bike Rohloff 203 disc, they can lock instantly. Only will need adjustment after 1 or 2 thousand miles. I have long pull SA levers on comfort bars. The LBS pro said I had the wrong ones, so obviously it doesn't fricking matter.
Now I don't have to worry about getting off, just pull the lever and I get thrown off. LOL
I have a DIY welded on plate with a homemade Alu bracket for extra adjustment slots.
The BB7 is way clunkier than the Spyre also, I made the mistake of trying it first.
And these are the same levers I use with SA drum brakes.
Get a TRP Spyre caliper with both side moving pads. Keep using the softer resin pads that grip better and don't squeal. They don't seem to care what the gap is either, I like more so they can't rub.
I've had them on my tour bike Rohloff 203 disc, they can lock instantly. Only will need adjustment after 1 or 2 thousand miles. I have long pull SA levers on comfort bars. The LBS pro said I had the wrong ones, so obviously it doesn't fricking matter.
Now I don't have to worry about getting off, just pull the lever and I get thrown off. LOL
I have a DIY welded on plate with a homemade Alu bracket for extra adjustment slots.
The BB7 is way clunkier than the Spyre also, I made the mistake of trying it first.
And these are the same levers I use with SA drum brakes.
Last edited by GamblerGORD53; 10-30-19 at 12:47 PM.
#24
Senior Member
Join Date: Feb 2017
Location: Northern Shenandoah Valley
Posts: 4,141
Bikes: More bikes than riders
Mentioned: 36 Post(s)
Tagged: 0 Thread(s)
Quoted: 1446 Post(s)
Liked 762 Times
in
570 Posts
TRP has both road and MTB versions of their brakes, too. Spyre is the road, or short-pull, version and Spyke is the MTB, or long-pull, version.
Last edited by hokiefyd; 10-30-19 at 12:55 PM.
#25
Full Member
Actually, get five or six TRP Spyre calipers (at least!) and try them all, one after another until you find one that works. QA and manufacturing tolerances on TRP Spyre are so crappy that buying just one caliper for each wheel will almost surely turn into an extremely frustrating experience, waste of time and waste of money.
BB5 and BB7 are much better made and offer exactly the same braking performance as TRP Spyre. No difference whatsoever.