front canti brake sqeal
#1
Senior Member
Thread Starter
Join Date: Dec 2007
Location: NWNJ
Posts: 3,704
Bikes: Road bike is a Carbon Bianchi C2C & Grandis (1980's), Gary Fisher Mt Bike, Trek Tandem & Mongoose SS MTB circa 1992.
Mentioned: 9 Post(s)
Tagged: 0 Thread(s)
Quoted: 722 Post(s)
Liked 353 Times
in
226 Posts
front canti brake sqeal
cantis on front make horrible sqealing noise.
what is fix.
pads relatively new.
just switched out wheels.
what is fix.
pads relatively new.
just switched out wheels.
#3
Senior Member
Join Date: Sep 2010
Location: Roswell, GA
Posts: 8,319
Bikes: '93 Trek 750, '92 Schwinn Crisscross, '93 Mongoose Alta
Mentioned: 30 Post(s)
Tagged: 0 Thread(s)
Quoted: 1438 Post(s)
Liked 1,092 Times
in
723 Posts
Use a fork crown-mounted cable stop to remove the root cause of canti brake squeal/shudder.
#4
Zip tie Karen
Join Date: Aug 2009
Location: Fair Oaks Ranch, TX
Posts: 7,004
Bikes: '13 Motobecane Fantom29 HT, '16 Motobecane Turino Pro Disc, '18 Velobuild VB-R-022, '21 Tsunami SNM-100
Mentioned: 26 Post(s)
Tagged: 0 Thread(s)
Quoted: 1465 Post(s)
Liked 1,542 Times
in
806 Posts
Normally, brake pad toe-in is the solution to this.
Likes For Phil_gretz:
#5
Senior Member
Join Date: Feb 2014
Location: SD
Posts: 2,745
Bikes: Handsome Fredward, Trek 1.1
Mentioned: 15 Post(s)
Tagged: 0 Thread(s)
Quoted: 481 Post(s)
Liked 131 Times
in
47 Posts
Lots of good points here.
Pad toe-in is key. Additionally, pay attention to make sure the pivot-to-pad distances are as identical as possible so both arms are equidistant to the rim and the face of the pads are the hitting the rim at the same angle.
New pads on new rims can be really grabby and will get better as they wear-in in my experience.
Pad toe-in is key. Additionally, pay attention to make sure the pivot-to-pad distances are as identical as possible so both arms are equidistant to the rim and the face of the pads are the hitting the rim at the same angle.
New pads on new rims can be really grabby and will get better as they wear-in in my experience.
#6
Full Member
Join Date: Oct 2019
Location: Foothills of West Central Maine
Posts: 410
Bikes: 2007 Motobecane Fantom Cross Expert, 2020 Motobecane Omni Strada Pro Disc (700c gravel bike), 2021 Motobecane Elite Adventure with Bafang 500W rear hub drive
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 174 Post(s)
Likes: 0
Liked 143 Times
in
94 Posts
When I got new wheels for my CX bike, the cantilever brakes squealed and shuddered. I changed out Kool Stop black and salmon for Red Kool Stops, and the problem was solved. Red are softer, I believe.
#7
The dropped
Join Date: Oct 2018
Location: Columbus, OH
Posts: 2,144
Bikes: Pake C'Mute Touring/Commuter Build, 1989 Kona Cinder Cone, 1995 Trek 5200, 1973 Raleigh Super Course FG, 1960/61 Montgomery Ward Hawthorne "thrift" 3 speed, by Hercules (sold) : 1966 Schwinn Deluxe Racer (sold)
Mentioned: 10 Post(s)
Tagged: 0 Thread(s)
Quoted: 1739 Post(s)
Liked 1,014 Times
in
696 Posts
Last tip!
Sometimes the pads can pick up a lot of new particles on new rims, or get contaminated by grease or lubes (it doesn't take much). Once you're done fiddling with pad setup, grab some isopropyl alcohol and wipe the pads' braking surface and the brake track to pull off any grease and brake dust.
Sometimes the pads can pick up a lot of new particles on new rims, or get contaminated by grease or lubes (it doesn't take much). Once you're done fiddling with pad setup, grab some isopropyl alcohol and wipe the pads' braking surface and the brake track to pull off any grease and brake dust.
#8
Senior Member
Thread Starter
Join Date: Dec 2007
Location: NWNJ
Posts: 3,704
Bikes: Road bike is a Carbon Bianchi C2C & Grandis (1980's), Gary Fisher Mt Bike, Trek Tandem & Mongoose SS MTB circa 1992.
Mentioned: 9 Post(s)
Tagged: 0 Thread(s)
Quoted: 722 Post(s)
Liked 353 Times
in
226 Posts
Last tip!
Sometimes the pads can pick up a lot of new particles on new rims, or get contaminated by grease or lubes (it doesn't take much). Once you're done fiddling with pad setup, grab some isopropyl alcohol and wipe the pads' braking surface and the brake track to pull off any grease and brake dust.
Sometimes the pads can pick up a lot of new particles on new rims, or get contaminated by grease or lubes (it doesn't take much). Once you're done fiddling with pad setup, grab some isopropyl alcohol and wipe the pads' braking surface and the brake track to pull off any grease and brake dust.
thank you.
this is what i have
Likes For thehammerdog:
#9
The dropped
Join Date: Oct 2018
Location: Columbus, OH
Posts: 2,144
Bikes: Pake C'Mute Touring/Commuter Build, 1989 Kona Cinder Cone, 1995 Trek 5200, 1973 Raleigh Super Course FG, 1960/61 Montgomery Ward Hawthorne "thrift" 3 speed, by Hercules (sold) : 1966 Schwinn Deluxe Racer (sold)
Mentioned: 10 Post(s)
Tagged: 0 Thread(s)
Quoted: 1739 Post(s)
Liked 1,014 Times
in
696 Posts
#10
Senior Member
Join Date: May 2005
Location: SFBay
Posts: 2,334
Bikes: n, I would like n+1
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 127 Post(s)
Likes: 0
Liked 133 Times
in
108 Posts
Just to throw something else into the mix, check your wheel bearings. You mentioned new wheels, if these are factory new you’re probably fine. If these are new-to-you used wheels I’d check them. I’ve made brake squeal go away by correcting loose hub bearings several times.